2020 Can-AM Ryker Technical Service Bulletins

18 technical service bulletins (TSBs) are on record for the 2020 Can-AM Ryker. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11019368Jun 6, 2025Other or unknown. Upon installation of the 2-UP passenger seat, difficulty to install might result in the breakage of the latch.
• 11003267Jun 21, 2024Suspension, Transmission and drivetrain, Electrical system. RYKER YAW Rate - SAS Sensor Faults These 3 faults (C0063 and/or C0051 and *C006C) can be triggered if the front suspension has excessive play or the front wheel alignment is out of specification
• 10254110Apr 2, 2024Engine cooling. Rykers 900 engines that may have the incorrect camshaft timing. Ryker Equipped with the 900 engine may start well when cold but then can have a rough idle or even dies at idle when the engine is warmed up.
• 10229607Dec 12, 2022Brakes, Electronic stability control, Suspension, Electrical system. Yaw rate sensor faults might be triggered due to loose front suspension components.
• 10226794Nov 30, 2022Vehicle speed control, Equipment. This TST includes solution for the noise that can be heard or felt under deceleration at high speed.
• 10226796Nov 16, 2022Electrical system. This bulletin is the detailed repair procedure if the position light and flasher electrical harness in the front fenders have rubbed on the tires wearing the insulating sheath.
• 10213476May 4, 2022Wheels. Message and alert to all dealer RYKER mandatory certification form The front wheel installation is a critical operation and must be performed as explained in the PDI bulletin.
• 10194662May 12, 2021Fuel system. Fuel Pump can be noisy especially when low fuel levels and warm temperatures.
• 10191570Apr 13, 2021Exterior lighting. Repair Procedure Revision- Brake Light Switch Adjustment Vehicle may indicate brake light switch failure, rear brake light stays ON or flashes intermittently.
• 10183375Nov 20, 2020Equipment, Engine cooling. We have some report that some 602 and 903 engines have been produced with the wrong camshaft. This document will help you to identify the correct one. If the wrong camshaft is installed the unit can have the following symptoms poor, idle, engine performance, O2 fault, engine misfire.
• 10181946Oct 27, 2020Suspension. YAW rate sensor faults might be triggered due to loose front suspension components.
• 10181962Oct 15, 2020Wheels. Safety Campaign- Possible Front Wheel Loss. The front wheel assembly may not have been performed properly (torque application and installation of the red locking clip).
• 10181959Oct 15, 2020Wheels. Safety Campaign Revision- Wheel nut may crack. One or more wheel nuts may crack resulting in a reduced clamping force. New VINs added in the warranty campaign and new steps in the procedure.
• 10176805Jun 20, 2020Electrical system, Brakes. Vehicle may indicate brake light switch failure. One of the probable cause is the adjustment of the brake light switch/low pressure switch.
• 10170875Feb 3, 2020Equipment, Engine cooling. This technical service tips is to show how to fix some leaks coming from the coolant cap area.
• 10170877Dec 2, 2019Engine cooling. Possible contact between the exhaust pipe and frame. Here are some ways to increase the distance between the exhaust pipe and the frame. The minimal distance between the exhaust pipe and the frame should be 5mm. Symptoms Excessive engine vibration felt, exhaust manifold bolts loose, engine rattle noise.
• 10166934Oct 3, 2019Equipment, Wheels. One or more wheel nuts may crack resulting in a reduced clamping force. This could eventually affect the integrity of the wheel assembly and the vehicle's behavior. This may increase the risk of a crash.
• 10171794Oct 2, 2019Suspension. Ryker 2020 Low Torque on FDU The bolts that holds the FDU to the swing arm are not torqued as specification for these vehicles.

← All problems reported for the 2020 Can-AM Ryker