2016 Chevrolet Tahoe Technical Service Bulletins

1,769 technical service bulletins (TSBs) are on record for the 2016 Chevrolet Tahoe. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10149058Oct 29, 2018Fuel system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
• 10149057Oct 29, 2018Visibility (wipers, defrost, mirrors). This Preliminary Information communication provides the technician with steps to resolve the issue of an oily substance that may be found on the inside windshield surface, and appears to be leaking from the rear view mirror area. Technician will remove the moisture sensor and clean the glass and mounting bracket with alcohol wipe. If the gel separates from the sensor the sensor will need to be replaced.
• 10149054Oct 29, 2018Seats. This Preliminary information communicates that an inoperative third row folding seat back may not fold down or up. This information advises dealers on how the seat functions and also a common area where an open circuit may be found between the third row seat module and the seat position sensor.
• 10149053Oct 29, 2018Electrical system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a click, rattle or a squeak nose coming from the dash. Technician will use Service Information to locate the Accessory AC and DC Power Control Module located to the right of the steering column. Remove the power inverter module and apply two sided tape to the module bracket to insulate…
• 10149051Oct 29, 2018Electrical system, Engine. This Preliminary Information communication provides information to the technician about vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on and Diagnostic Trouble Code P0300 - P0308 may set. Technician will inspect for lose sparkplug wire. If a spark plug wire is found lose check for a missing ?C? clip on the wire end for the ignition coil. If the clip is missing replace the wire.
• 10147401Oct 23, 2018Equipment. This Preliminary information communicates
• 10147382Oct 16, 2018Engine cooling. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308.
• 10147367Oct 10, 2018Equipment. This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
• 10147362Oct 9, 2018Electrical system, Body and structure. This Preliminary information communicates to the technician when diagnosing intermittent circuit concerns to look at the connector for missing weather pack seals that could allow water intrusion into the connector and lead to corrosion on the terminals.
• 10147348Oct 3, 2018Fuel system. This Preliminary information communicates that when removing the fuel line jumper hose care should be taken to be sure the line is reinstalled correctly to avoid a no/low fuel pressure situation.
• 10147342Oct 1, 2018Body and structure. This Preliminary information communicates if the liftglass will not open using keyless entry to verify Valet Mode is not enabled.
• 10145501Sep 19, 2018Transmission and drivetrain. This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
• 10145500Sep 19, 2018Electronic stability control. This Preliminary Information communication provides information to the technician about vehicles that have an unwanted Stability Activation and/or a Service Stability message on the Driver Information Center. Technician may find a Diagnostic Trouble Code C0710. Technician should inspect for vehicles modifications before any in-depth diagnostics are performed.
• 10145486Sep 14, 2018Suspension. This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer…
• 10145483Sep 14, 2018Body and structure. This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.
• 10145479Sep 13, 2018Brakes. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line…
• 10145470Sep 10, 2018Engine cooling. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
• 10145469Sep 10, 2018Other or unknown. This Preliminary Information communication provides information to the technician about customers that may request the factory Integrated Trailer Brake Controller Regular Production Option Code (JL1) be installed on their Full-Size Pickup or SUV when the vehicle was not ordered with the option. Dealer should advise the customer it cannot be added to the vehicle.
• 10144476Aug 28, 2018Equipment. This Preliminary Information communication provides information to the technician that General Motors Technical Assistance Center may ask for Global Diagnostic System 2 Session Log. Technician will need use Global Diagnostic System 2 to send the session logs to General Motors Technical Assistance Center for further assistance on the vehicle in question.
• 10144464Aug 20, 2018Lane departure. This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that…
• 10144458Aug 14, 2018Electrical system, Equipment. This Preliminary Information communication provides information to the technician about vehicles that have a “Service 4WD Message” displayed in the Driver Information Center. Technician may find Diagnostic Trouble Codes C0392 or C0396. Technician should check the terminal tension on the Transfer Case Control Module X1 connector. Technician should repair any terminal that have poor terminal tension.
• 10187431Aug 8, 2018Equipment. This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
• 10186122Aug 8, 2018Equipment. This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
• 10145171Aug 8, 2018Equipment. 17336 04 - Special Coverage (Warranty Information Revised). On some vehicles, may have a condition where thermal cycling on the combination transmission fluid/oil and AC condenser cooler creates a crack that may allow refrigerant to escape. This condition consequently may deactivate the AC system which may cause potential customer annoyance. Dealers are to inspect the air conditioning condenser and replace if…
• 10144451Aug 8, 2018Engine. This Preliminary Information communication provides information to the technician about engine block of possible cylinder bore damage, scoring or out of round as the possible cause of engine oil consumption, misfire, cylinder leakage or blow by. Technician will need to inspect the engine for Cylinder damage or scoring, An out of round cylinder bore, Dirt intrusion, and Catalytic Converter failure.
• 10143777Jul 23, 2018Seats. This Preliminary information communicates a diagnostic tip for an issues with the heated and/or vented seats turning off and setting DTCU1524 because of a loss of voltage to the Seat Heating Control Module.
• 10143758Jul 9, 2018Equipment. This Preliminary Information communication provides information to the technician on how to tell the difference between the integrated center stack, the radio, the human machine interface, and the vehicle communication interface module. There are pictures of all the individual modules for identification purposes.
• 10143757Jul 9, 2018Transmission and drivetrain. This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low…
• 10143756Jul 6, 2018Lane departure. This Preliminary Information communication provides information to the technician about vehicles thatmay have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view…
• 10143752Jul 3, 2018Visibility (wipers, defrost, mirrors). This Preliminary Information communication advises the technician the steps on diagnosing the concern. Customer's sunroof operation intermittent, bind, noise, auto-reverse, and/or water leaks.
• 10143459Jun 27, 2018Equipment, Engine. This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
• 10143456Jun 26, 2018Equipment, Electrical system. This Preliminary Information communication provides information to the technician the steps to diagnose and repair the concern of the display is showing 32° F (0° C) after a battery or reprogramming a module. The outside temperature will begin to update if driven above 20 mph for at least 5 minutes. If the vehicle speed drops below 20 mph, the timer will reset and the display will stop updating.
• 10143455Jun 26, 2018Body and structure, Visibility (wipers, defrost, mirrors). This Preliminary Information communication provides information to the technician on a concern of wind buffeting noise and/or water leak.Technician is to follow the steps to apply vibration control material between the sunroof roof bow and the roof sheet metal.
• 10143449Jun 20, 2018Equipment. This Preliminary Information communication provides information to the technician about vehicles that the Heater-Vent-Air Conditioning blows warm air. Before calling General Motors Technical Assistance Center technician will need to have high and low pressures, outside temperature, humidity, and vent temperature.
• 10143443Jun 14, 2018Equipment. This Preliminary Information communication provides information to the technician about vehicles that may have an issue when using Bluetooth voice recognition with an iPhone. Technician should work with the customer to insure the phone contacts to not have any Emojis loaded to any contact.
• 10143439Jun 12, 2018Electrical system. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector…
• 10143438Jun 12, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
• 10143434Jun 12, 2018Steering. This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
• 10143433Jun 12, 2018Air bags, Steering, Transmission and drivetrain, Suspension, Other or unknown…. This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the…
• 10143432Jun 12, 2018Equipment. This Preliminary information communicates instructions dealer to inspect for a broken or damaged side objector sensor/module bracket if there is a "Side Detection System Unavailable" message displayed at startup.
• 10143430Jun 12, 2018Suspension, Body and structure. This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
• 10143429Jun 11, 2018Engine, Electrical system. This Preliminary Information communication provides the technician with steps on how to program an Engine Control Module when getting a Service Programming System error code E4491 or E4423. In some cases Techline Customer Support Center may need to be contacted to resolve the issue.
• 10143428Jun 11, 2018Body and structure. This Preliminary information communicates and issue with an itch, rattle, flutter, squeak, tick, and/or chirp type noise coming from the left I/Por A-pillar area caused by contact between the drivers fender and A pillar.
• 10143424Jun 6, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
• 10141379May 30, 2018Seats, Equipment. This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
• 10141372May 24, 2018Brakes, Electrical system. This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct…
• 10141371May 23, 2018Equipment, Electrical system. This Preliminary Information communication provides information to the technician about connectivity concerns when connecting an Apple device via USB cord. Technician should insure the customer is using an original equipment manufacturer Apple USB cable.
• 10141367May 22, 2018Electrical system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake…
• 10141365May 18, 2018Engine cooling, Equipment. This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
• 10141364May 18, 2018Engine cooling, Equipment. This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.

← All problems reported for the 2016 Chevrolet Tahoe