2016 GMC Sierra 1500Service bulletins

2016 GMC Sierra 1500 Technical Service Bulletins

1,214 technical service bulletins (TSBs) are on record for the 2016 GMC Sierra 1500. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

10143439Jun 12, 2018Electrical system. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector…
10143438Jun 12, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
10143434Jun 12, 2018Steering. This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
10143433Jun 12, 2018Air bags, Steering, Transmission and drivetrain, Suspension, Other or unknown…. This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the…
10143430Jun 12, 2018Suspension, Body and structure. This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
10143424Jun 6, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
10141380May 30, 2018Equipment. This Preliminary information communicates information to have dealers contact TCSC for programming assistance with new amplifier part numbers until all the new amplifier numbers are setup correctly for programming.
10141379May 30, 2018Seats, Equipment. This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
10141372May 24, 2018Brakes, Electrical system. This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct…
10141367May 22, 2018Electrical system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake…
10141365May 18, 2018Engine cooling, Equipment. This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
10141364May 18, 2018Engine cooling, Equipment. This Preliminary information communicates to the dealer an issue where the vehicle's engine may crank over unprompted and not start afterward. This is the result of hooking up the Active Fuel Injector Tool incorrectly on vehicles equipped with a direct fuel injection system. This Preliminary information instructs the dealer ofa repair kit they received that will prevent this issue when installed correctly.
10141362May 17, 2018Electrical system, Equipment. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
10137530Apr 30, 2018Engine cooling, Electrical system. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the hybrid/EV battery Pack, Hybrid/EV Powertrain Control Module (HPCM2), High Voltage Battery Interface Control Module 1 and 2, Drive Motor Generator Battery Cooling Blower. The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
10137526Apr 27, 2018Exterior lighting. This Preliminary Information communicates to techniciansthat the Daytime Running Lamps (DRL's) or the auto headlamps will not shut off when using the daytime running lamp disable switch (Which is part of the headlamp switch), if the vehicles was built for Canada (RPO Z49). These vehicles were built with different software that doesn't allow the DRL's or Auto headlamp to be shut off. Canada law prohibits…
10137522Apr 27, 2018Electrical system. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for theGenerator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
10137521Apr 27, 2018Engine cooling, Transmission and drivetrain, Fuel system, Electrical system. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find…
10137209Mar 28, 2018Engine. This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
10137207Mar 27, 2018Back-over prevention (rear camera). This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct…
10137203Mar 27, 2018Fuel system, Engine. This Preliminary Information communication provides information to the technician about vehicles that have extended or long crank time during cold ambient air temperatures. Direct Injection systems run at higher pressures, and the mechanical pump on the engine must build up the required pressure before the first injection event occurs. Direct Injection engines may have slightly longer cold crank times than that of…
10137202Mar 27, 2018Electrical system. This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
10137201Mar 26, 2018Electrical system. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer…
10137199Mar 26, 2018Wheels. This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
10137197Mar 22, 2018Engine cooling. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
10137188Mar 15, 2018Engine. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and…
10137182Mar 12, 2018Engine cooling. This Preliminary Information communication provides information to the technician of a complaint of a sag or hesitation when accelerating. The concern is present when coasting at low speeds of less than 15 miles per hour and then aggressively applying the throttle, or after making a hard stop followed by an aggressive throttle.
10137167Mar 1, 2018Electrical system. This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
10137378Feb 26, 2018Equipment, Electrical system. This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
10137350Feb 13, 2018Exterior lighting. This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Both Front Low Beam, High Beam, Day Time Running Lamps (DRL) and Turn Signals Inoperative.
10129881Feb 9, 2018Back-over prevention (rear camera). This Preliminary information communicates repair information for therear vision camera or surround vision camera image being: - Yellow - Blurry -Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
10129880Feb 9, 2018Equipment. This Preliminary information communicatesOperational Tips/Support For GM Accessory Three Camera Trailering System Package By EchoMaster.
10129879Feb 9, 2018Equipment. This Preliminary Information communication advises the technician that some vehicles may have a dim Driver Information Center when the interior of the vehicle is hot from a sun load or extended heater operation. The Driver Information Center is designed to dim with high temperature exposure. This is done to protect the Driver Information Center from damage.
10129878Feb 9, 2018Suspension. This Preliminary Information communication provides information to the technician on the steps to help diagnose and repair vehicles with a rattle, squeak, clunk, thump, or bump. If published Service Information diagnostics do not lead to a repair for the concern. Technician should inspect the opposite side shock/strut for the cause of the concern.
10129877Feb 9, 2018Suspension, Electrical system. This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole.
10129873Feb 8, 2018Fuel system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have rattle or ticking noise that is louder inside the vehicle than outside. The noise may also sound like a lifter tick. If the noise is heard best at the fuel line and the sound will be real loud with a stethoscope. The fuel line will need to be replaced.
10129868Feb 7, 2018Engine. This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
10129857Feb 5, 2018Electrical system. This Preliminary Information communication provides information to the technician about a no start or another concern after swapping an Engine Control Module or other modules from one vehicle to another. The Global Architecture electrical system associated with these vehicles does not allow controller swaps between vehicles.
10129106Jan 31, 2018Electrical system. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the A15, Starter Generator (MGU). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance.
10129102Jan 30, 2018Electrical system. This Preliminary Information communication provides information to the technician about vehicles that the voice recognition is inoperative. Technician will need to toggle through all languages then back to the desired language.
10129101Jan 26, 2018Electrical system. This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start,or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the…
10129093Jan 24, 2018Exterior lighting. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308.
10129091Jan 24, 2018Engine cooling. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
10129088Jan 23, 2018Brakes. This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn.
10129084Jan 19, 2018Equipment. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have intermittent and hard to duplicate Rear Camera blank, distorted, or fuzzy. Also no radio, OnStar, or speech audio and the volume is unable to be adjusted from the integrated center stack or the steering wheel controls. The driver information center will show “No…
10129082Jan 19, 2018Fuel system, Steering, Lane departure, Transmission and drivetrain, Electronic…. This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that…
10129080Jan 19, 2018Steering, Seat belts, Electrical system, Wheels, Brakes. This Preliminary Information communication provides information to the technician about vehicles that may have hard or unable to rotate ignition key concern. When the concern is present the steering wheel will need to be rotated in either direction to alleviate the pressure between the steering column lock pin and lock plate. Please communicate to the customer this condition is a normal operating characteristic of…
10129077Jan 19, 2018Body and structure, Exterior lighting. This Preliminary Information communication provides information to the technician about vehicles that have either the truck or the snowplow's headlights are flickering or inoperative. There may be a diagnostic trouble code B2575 and or a B2699 set in the body control module. Technician will need to contact the snowplow manufacturer for additional information on their headlight changeover system.
10129075Jan 18, 2018Back-over prevention (rear camera). This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
10129071Jan 16, 2018Engine cooling. This Preliminary Information communication provides information to the technician about vehicles that have a coolant loss and/or coolant odor after driving the vehicle. Technician will need to test the cooling system looking for leaks at the outer head bolts. If coolant is found replace the head the concern is present on.
10129067Jan 16, 2018Fuel system, Back-over prevention (rear camera), Transmission and drivetrain. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a no crank concern. Technician will need to check the valve train for movement when the engine is cranked. If the valve train is not moving while the crankshaft is moving the front cover will need to be removed to inspect for a sheared cam sprocket locator pin. If the cam…

← All problems reported for the 2016 GMC Sierra 1500

About this data. Data from NHTSA (ODI) complaints, recalls, TSBs and investigations, updated Nov 1, 2026. Complaints are unverified consumer reports and may be duplicated or inaccurate.