2019 Hyundai Santa FE Technical Service Bulletins

185 technical service bulletins (TSBs) are on record for the 2019 Hyundai Santa FE. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10170511Dec 17, 2019Equipment, Transmission and drivetrain. If you are servicing a vehicle with a transmission slipping concern, follow the Service Procedure shown below and perform a stall test. This TSB provides a procedure to test each clutch in the transmission. If the vehicle fails the stall test, replace the transmission. ? PASS: Stall speed is between 1700~2900 rpm (See shop manual for stall speed). ? FAIL: Engine revs to redline limit (6,000~6,500 rpm). If so…
• 10169380Nov 15, 2019Electrical system. If you are servicing a vehicle with the DTC or symptoms listed below, refer to the Service Procedure to diagnose the condition. ? Diagnostic trouble codes: ?P0705 - Range switch sensor circuit ?P0706 - Range switch range/performance ?P0707 - Range switch - open circuit ?P0708 - Range switch - short circuit or multiple inputs ? Symptoms: ?Malfunction Indicator Light (MIL) illuminated ?4th gear fail-safe ?No gear…
• 10169370Nov 4, 2019Back-over prevention (rear camera), Lane departure. The Blind Spot Detection (BSD) or Blind-Spot Collision Warning (BCW) is a system that measures the speed of and distance from the following vehicles by using two magnetic wave radar sensors attached in the rear bumper. The BSD/BCW detects vehicles within the blind spot zone and gives off an alarm (visual and audible). The two magnetic radar sensors provide these functions for BSD/BCW: ? Senses other vehicles in the…
• 10167769Oct 28, 2019Engine, Equipment. The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
• 10167768Oct 28, 2019Electrical system, Equipment. Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.
• 10167767Oct 28, 2019Engine, Electrical system. Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to…
• 10167765Oct 28, 2019Engine, Equipment, Electrical system. Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure.
• 10167764Oct 28, 2019Engine, Equipment, Electrical system. Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P132600.
• 10167269Oct 28, 2019Engine cooling. The warranty coverage for the engine long block has been extended to 10 years or 120,000 miles from the date of original retail delivery or date of first use, whichever occurs first, and is valid for original and subsequent owners.
• 10167268Oct 28, 2019Engine cooling. Applicable vehicles with 2.0L Turbo and 2.4L GDI engines may experience the Check Engine warning lamp illuminated with DTC P1326. Follow the procedure to inspect the vehicle and install a wire harness extension and/or replacement engine based on the inspection results.
• 10167267Oct 28, 2019Engine cooling. Hyundai is conducting a product improvement campaign to enhance the knock sensor software to detect abnormal engine bearing noise before potentially severe engine damage occurs. If abnormal engine bearing noise is detected, the Malfunction Indicator Lamp (MIL) will blink continuously, a chime will sound on certain vehicles, and the vehicle will be placed in Engine Protection Mode allowing the customer to drive to…
• 10167260Oct 28, 2019Engine cooling. Hyundai has developed a new engine monitoring technology called a Knock Sensor Detection System (KSDS). The technology uses software innovations and leverages existing engine sensors to continuously monitor for symptoms that may precede an engine failure.
• 10167258Oct 28, 2019Engine cooling. Hyundai has launched a Service Campaign for applicable vehicles with 2.0L Turbo and 2.4L GDI engines that may experience the Check Engine warning lamp illuminated with DTC P132600.
• 10167760Oct 14, 2019Equipment. This bulletin provides instructions on the replacement of a cup holder with retaining tabs which cannot stabilize a cup due to inner O-ring displacement.
• 10167254Oct 14, 2019Equipment. This bulletin provides instructions on the replacement of a cup holder with retaining tabs which cannot stabilize a cup due to inner O-ring displacement.
• 10167253Oct 14, 2019Equipment. This bulletin provides instruction detailing the proper methodology for scanning and uploading captured GDS data files to the Techline Repository. Compliance with this bulletin ensures that the GDS data files are correctly transferred and matched with a Techline Case number.
• 10167733Oct 7, 2019Engine. This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines.
• 10167235Oct 7, 2019Transmission and drivetrain. This bulletin provides information regarding the changes in the timing chain and the crankshaft sprockets on certain Azera (HG), Santa Fe/Santa Fe XL (NC), Genesis (BH/DH), Genesis Coupe (BK), and G90 (HI) vehicles equipped with Lambda 3.3L / 3.8L GDI engines.
• 10165466Aug 19, 2019Electrical system, Equipment, Engine. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related oil pressure harness with integrated oil temperature sensor.
• 10165463Aug 15, 2019Equipment, Transmission and drivetrain. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related input/output speed sensor and oil pressure harness.
• 10165462Aug 15, 2019Engine cooling, Electrical system. If you are servicing an applicable vehicle with a ?Check Engine? light on and one or more of the DTC listed below, follow the repair procedure and replace the related solenoid and oil pressure harness.
• 10163866Jul 23, 2019Brakes. This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
• 10163862Jul 3, 2019Transmission and drivetrain. If you are servicing a 2019 Santa Fe (2.0T) with a harsh 2-3 or 3-4 upshift when cold, follow the Service Procedure below.
• 10163288Jun 20, 2019Brakes, Wheels. This bulletin provides information on the rear wheel speed sensor for Santa Fe (CM), Santa Fe / XL (NC), Santa Fe Sport (AN), and Veracruz (EN) vehicles equipped with front wheel drive (FWD). The rear wheel speed sensor is available as a separate service part from the rear wheel hub assembly. When appropriate, it is recommended to replace only the rear wheel speed sensor instead of the full assembly.
• 10163279Jun 4, 2019Transmission and drivetrain. This TSB provides a procedure to diagnose and repair a transaxle for the following Incorrect Ratio DTC (transaxle clutch slipping more than 200 rpm in gear).
• 10161684May 2, 2019Lane departure, Electrical system, Forward collision avoidance. This bulletin provides information for replacement of the Blind-Spot Collision Warning (BCW) module. Whenever the left or right side BCW module is being replaced, it is required to perform the variant coding procedure. If the variant coding procedure is not performed, a DTC C1743 (S/W mismatch) will be triggered.
• 10160106Apr 22, 2019Steering. This bulletin provides information regarding replacement of the column-mounted Motor Driven Power Steering (MDPS) system as separate components.
• 10160098Apr 15, 2019Electrical system, Transmission and drivetrain. This bulletin provides the procedure to write the Vehicle Identification Number (VIN) during the replacement of the Engine Control Module (ECM) or Powertrain Control Module (PCM). Once the VIN has been programmed to the ECM/PCM, it cannot be removed or overwritten.
• 10158803Mar 13, 2019Visibility (wipers, defrost, mirrors). This bulletin provides information on the serviceable parts for the outside mirror assembly. When diagnosing and repairing the outside mirror, do not replace the entire assembly. Refer to page 2 of this TSB for replacement of individual parts.
• 10158796Mar 6, 2019Electrical system. This bulletin describes the Santa Fe (TM) Idle Stop and Go (ISG) system operations and battery sensor recalibration procedure. Refer to applicable Work Shop Manual and Owner?s Manual for additional information
• 10154683Feb 18, 2019Fuel system. In a gasoline direct injection (GDI) engine, highly pressurized gasoline is injected via a common rail fuel line and injectors that deliver fuel directly into the combustion chamber of each cylinder. In comparison, in a conventional multi-point fuel injection (MPI) engine, relatively low pressure gasoline is injected into the intake port of each cylinder. Due to high fuel pressures in a GDI system, servicing the…
• 10152863Dec 17, 2018Electrical system. This bulletin provides information related to the Engine Control Module (ECM) and Electronic Stability Control (ESC) software updates for certain 2019MY Santa Fe (TM) equipped with 2.4L engine. The ECM update is revised for starting performance and Idle Stop & Go (ISG) control logic. In addition, the ESC update is revised for hold timing of Hill-start Assist Control (HAC) function to optimized ISG operation.
• 10152862Dec 17, 2018Electrical system. Hyundai Motor America is conducting a Service Campaign to update the ECM & ESC on certain 2019 model year Santa Fe 2.4L vehicles. Service Campaign T3M provides a service procedure to update the ECM & ESC software.
• 10151894Nov 2, 2018Transmission and drivetrain. The vehicles listed below are equipped with an 8-speed front-wheel drive transmission. Do not replace the transmission for any of the solenoid DTC listed below. Instead, follow the Service Procedure on Page 2 and replace the related part.
• 10151893Nov 2, 2018Transmission and drivetrain. This bulletin provides a procedure to transfer pressure data to the TCU using GDS Mobile. This procedure is necessary to reduce the transmission learning time and improve the shift quality.

← All problems reported for the 2019 Hyundai Santa FE