2007 Mazda B-Series Truck Technical Service Bulletins

80 technical service bulletins (TSBs) are on record for the 2007 Mazda B-Series Truck. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10134930Mar 26, 2018Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10134929Mar 26, 2018Electrical system. The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10134928Mar 26, 2018Electrical system. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10134703Mar 26, 2018Equipment. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is…
• 10134702Mar 22, 2018Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10118753Sep 12, 2017Air bags. STOPPER PLATES FOR AIR BAG MODULE CONNECTORS HAVE BEEN ESTABLISHED AS NEW SERVICE PARTS. When removing the connector (1) to the air bag module (2), make sure to first lift the stopper plate (3) carefully using a flathead screwdriver (but do not remove it), and then pull out the connector.
• 10118467Aug 7, 2017Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10111036Jul 12, 2017Electrical system. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is© 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.
• 10213430Feb 26, 2016Electrical system. Excessive condensation or water within the headlamp assembly caustion
• 10213422Feb 2, 2016Equipment. Proper usage of driver's floor mat.
• 10100890Jan 25, 2016Equipment. Always be sure to use the correct automatic transmission fluid when replacing atf. Using the wrong atf may cause shift quality complaints or may even damage the transmission.note:• atf m-v (type m5) is not the same fluid as mercon®v or mercon®lv atf.• atf m-v (type m5) has a greater viscosity than mercon®v and mercon®lv atf in low temperatures.• atf m-v (type m5) has a greater anti-judder specification than…
• 10098367Aug 15, 2014Equipment. In accordance with federal regulations, follow the procedure listed below when replacing a speedometer.note:•mazda vehicles are manufactured with tamper-proof speedometers.•when a speedometer is replaced, the new speedometer will read zero (0) miles.•this procedure is extremely important to accurately represent actual vehicle mileage.•prior to speedometer removal, complete the information required on the…
• 10098282Jun 10, 2014Equipment. This service bulletin provides information regarding the proper use of the driver’s floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. • floor mat moves forward due to improper installation. • inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. • floor mat is…
• 10098245Jun 10, 2014Equipment. Mazda north american operations received many requests from our dealers asking us to approve additional on-car brake lathes as an option for mnao authorized equipment. Due to your feedback and after evaluating a few on-car brake lathes, we are pleased to announce that we have added the pro cut on-car brake lathe to mnao authorized equipment program. The accu-turn is still an approved brake lathe but it is no longer…
• 10097375Apr 17, 2013Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner’s manual. Services performed outside of mazda’s factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10097348Mar 11, 2013Transmission and drivetrain. Always be sure to use the correct automatic transmission fluid when replacing atf. Using the wrong atf may cause shift quality complaints or may even damage the transmission.note:•atf m-v (type m5) is not the same fluid as mercon®v or mercon®lv atf.•atf m-v (type m5) has a greater viscosity than mercon®v and mercon®lv atf in low temperatures.
• 10097343Mar 11, 2013Equipment. This service bulletin provides information regarding the proper use of the driver’s floor mat to avoid any poten-tial interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.•floor mat moves forward due to improper installation.•inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used.•floor mat is…
• 10052155Mar 11, 2013Equipment. Mazda: on some vehicles, to avoid potential interference of foot placed on pedals, information is provided regarding proper use, and placement, of driver's floor mat. Various models and model years.
• 10097367Mar 4, 2013Transmission and drivetrain. Always be sure to use the correct automatic transmission fluid when replacing atf. Using the wrong atf may cause shift quality complaints or may even damage the transmission.note:•atf m-v (type m5) is not the same fluid as mercon®v or mercon®lv atf.•atf m-v (type m5) has a greater viscosity than mercon®v and mercon®lv atf in low temperatures. •atf m-v (type m5) has a greater anti-judder specification than mercon®v…
• 10097295Jan 15, 2013Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner’s manual. Services performed outside of mazda’s factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10097300Jan 14, 2013Equipment. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10097942Dec 19, 2012Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner’s manual. Services performed outside of mazda’s factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10024586Apr 28, 2008Steering. Pop/click/clunk noise from front end when turning at slow speeds. *nj updated 5/30/08.
• 10023313Sep 7, 2007Suspension. Front crankshaft bolt service warning.
• 10021610Apr 18, 2007Other or unknown. Availability of non-required tools.
• 10021564Apr 5, 2007Engine cooling. No start/loss of engine timings/scraping noise at crankshaft pulley/possible engine damage.
• 10021563Apr 3, 2007Engine cooling. Mil comes on with dtc p0607.
• 10021215Feb 8, 2007Engine cooling. Mil (malfunction indicator lamp) comes on with dtc (diagnostic trouble code) p0401.
• 10019978Dec 12, 2006Tires. Tire pressure monitoring system (tpms) indicator light on - tire pressure sensor training procedure.
• 10021000Oct 4, 2006Air bags. Non genuine accessories affect air bag operation.

← All problems reported for the 2007 Mazda B-Series Truck