2018 Mazda CX-3 Technical Service Bulletins

477 technical service bulletins (TSBs) are on record for the 2018 Mazda CX-3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10153294Dec 7, 2018Equipment. Some customers may complain about SIRIUSXM satellite radio does not show album art, artist biographies or station logos in the center display. This is a normal condition. Album art and artist biographies are not provided by SiriusXM Satellite Radio, a blank white square frame is shown in place of the album art. Note: This information is also available at www.mazdahandsfree.com>FAQ>ENTERTAINMENT - SIRIUSXM®. STATION…
• 10154138Dec 5, 2018Electrical system, Equipment. Some customers may complain about improper operation of the MAZDA CONNECT system when streaming music with audio source aha/Pandora/Stitcher/Bluetooth® and the same device is also connected to the USB port for charging.
• 10153293Dec 5, 2018Electrical system. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTC is stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. The combination of warning lights mentioned by the customer may include: SCBS/SBS, LAS/LDWS, HBC, Master Warning Light.
• 10153289Dec 5, 2018Equipment. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin.Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.100A or later).
• 10153301Nov 27, 2018Equipment. SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.
• 10153300Nov 27, 2018Electrical system. Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery…
• 10152372Nov 27, 2018Electrical system. SMS (Short Message Service) messages received by paired phones (Android and iPhone 5 iOS 7.0 or higher) can be downloaded, displayed, and played (text to voice) on vehicles equipped with MAZDA CONNECT. When parked, new messages can be displayed or read by the system. When driving, new messages can be read to the vehicle occupants.
• 10152371Nov 27, 2018Electrical system, Tires. Some vehicles (with MAZDA CONNECT) may exhibit a condition where DTC U0323(PCM) / U0423(ABS) /U3000(IC) CANNOT be deleted when the TPMS warning light flashes and/or the TCS/DSC indicator lights are illuminated. This can happen if the ignition is turned OFF within 20 seconds after the ignition is turned ON in one of the following two situations. 1. The ?ROOM? fuse (Engine compartment) is NOT installed when battery…
• 10153299Nov 20, 2018Engine cooling. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION…
• 10152370Nov 20, 2018Engine cooling. If an oil pressure inspection is needed on a SKYACTIV-G engine, use the Special Service Tool (SST) set shown below and refer to the instructions on MGSS online: CX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), MX-3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0] ), Mazda6: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.5] ), Mazda3: (OIL PRESSURE INSPECTION [SKYACTIV-G 2.0, SKYACTIV-G 2.5] ), CX-5: (OIL PRESSURE INSPECTION…
• 10152379Nov 13, 2018Exterior lighting, Body and structure. Some customers may notice water entry into the front combination lights. This is due to poor sealing where rain or other water can enter inside the light. To eliminate this concern, the shape of the front combination light has been changed to improve sealing ability.
• 10152381Nov 9, 2018Lane departure. Some customers may experience a Blind Spot Monitoring (BSM) system that does not detect a vehicle in the BSM alert area. The BSM indicator light on the outer door mirror glass will not illuminate and no DTC's are stored. The BSM system may operate when switching the ignition switch OFF, then ON. This may be caused by low battery voltage that stops its operation during the drive cycle, even if the voltage recovers.
• 10152382Nov 6, 2018Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
• 10148073Oct 25, 2018Engine, Electrical system. Some vehicles equipped with MAZDA CONNECT may exhibit the following oil maintenance monitor concerns on the center display: The wrench light (Oil Change Due message) cannot be cleared using MAZDA CONNECT/Applications/Vehicle Status Monitor/Maintenance reset menu. The wrench light (Oil Change Due message) is displayed before the oil change is due.
• 10148072Oct 10, 2018Vehicle speed control, Equipment. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10148071Oct 10, 2018Equipment, Body and structure. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may becaused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.
• 10148070Oct 10, 2018Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following…
• 10148069Oct 10, 2018Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
• 10148068Oct 10, 2018Equipment, Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
• 10148003Oct 10, 2018Brakes, Equipment. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims…
• 10148002Oct 10, 2018Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10145252Sep 14, 2018Electrical system. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
• 10145251Sep 14, 2018Steering, Wheels. Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel to the left. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for steering shaft has been modified.
• 10145239Sep 14, 2018Electrical system, Engine. Some customers may complain about: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator, light flashing, Battery discharge, Electrical relay buzzing noise.This may be caused by: A key in a purse near a cell phone. The cell phone radio waves may interrupt the immobilizer system. An aftermarket cell phone charger. The charger may produce…
• 10145238Sep 14, 2018Electrical system. Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger, GPS tracker...) may create excessive electrical noise. The noise may interrupt some of the vehicle electrical systems. Below are a few examples of an aftermarket cell phone charger and…
• 10145237Sep 14, 2018Equipment, Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10145242Sep 6, 2018Engine cooling. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is…
• 10145248Sep 5, 2018Transmission and drivetrain. Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the drive shaft. To correct this issue, the thickness of the dust cover has been…
• 10145245Sep 4, 2018Suspension. Some vehicles may experience a creaking noise from the front shock absorber when going over bumps. Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. It may be found during maintenance or service opportunity without customer complaints. Mud and sand caught between the coil spring and the lower spring seat causes paint damage on the coil spring, resulting in…
• 10144333Aug 31, 2018Vehicle speed control. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10144332Aug 17, 2018Electrical system. Some customers may experience the active driving display (auto flip-up type) does not flip up and no DTC is stored. Due to improper assembly, a deformed bracket may cause a loose mesh between internal gears. To correct this issue, the active driving display has been changed.
• 10144327Aug 17, 2018Transmission and drivetrain. Some vehicles may exhibit a squeak noise from the right front driveshaft at the transaxle when driving. This concern is likely to occur when driving at speeds between 37-50 mph (60-80 km/h) with the ATF at normal operating temperature. The noise is caused by stick/slip between the oil seal at the transaxle and the dust cover of the driveshaft. To correct this issue, the thickness of the dust cover has been increased.
• 10144334Aug 15, 2018Transmission and drivetrain. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
• 10144322Aug 13, 2018Equipment. Dealer Rework (DRW) 13 - Mazda Connect Navigation Concern. As you may know, DRW13 was launched in March of 2018. This notice is to advise all dealers that DRW13 will be ending August 16th 2018 and all claims must be submitted by this date.
• 10144324Aug 10, 2018Lane departure. In support of the new Mazda MX-5 and CX-3, Mazda will make available for loan on a "as-needed" basis, a Special Service Tool (SST) to allow for the radar aiming of the blind spot monitoring (BSM) system. The(BSM) radar aiming is performed whenever the (BSM) control module, the (BSM) bracket or the rear bumper is replaced. The tool is available for loan by contacting DAG.
• 10143982Jul 30, 2018Electrical system. MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Inform the customer that all they need to do is update the MMS APP to the latest version to get rid of the error message.
• 10144013Jul 20, 2018Equipment, Engine. ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.
• 10144012Jul 20, 2018Electrical system, Engine, Visibility (wipers, defrost, mirrors). ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle…
• 10144010Jul 20, 2018Equipment, Electrical system. ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of…
• 10143980Jul 16, 2018Equipment. Mazda connect system frequently asked questions (faq)
• 10143974Jul 13, 2018Suspension. Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. The shape and material of the dust boot has been changed to improve its resistance to cold.
• 10143976Jul 10, 2018Transmission and drivetrain. Some customers who drive at elevations higher than 3,300 ft (1,000 m) may complain of a shift shock felt when shifting into 3rd, 5th and/or Reverse with no AT related DTCs stored. The symptom can be temporarily repaired using the AT initial learning procedure, but may recur after multiple driving cycles. Applicable situations: Shifting up: 2-3 or 4-5 Shifting down: 4-3 or 6-5 NOTE: Shifting from 2-3 or 4-3 is more…
• 10143978Jul 6, 2018Electrical system, Forward collision avoidance. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTC is stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. The combination of warning lights mentioned by the customer may include: SCBS/SBS LAS/LDWS HBC Master Warning Light Instrument Cluster Multi-Information Display (if equipped)…
• 10143957Jun 27, 2018Equipment. When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Refer to MGSS (RADAR UNIT INSPECTION) for proper diagnosing.
• 10143965Jun 20, 2018Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following…
• 10143964Jun 6, 2018Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10143955Jun 6, 2018Engine cooling. IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the…
• 10142534May 23, 2018Seat belts, Air bags. Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.
• 10142527May 11, 2018Equipment. Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement.
• 10142517May 11, 2018Engine cooling. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.

← All problems reported for the 2018 Mazda CX-3