2015 Mazda MAZDA3 Technical Service Bulletins

744 technical service bulletins (TSBs) are on record for the 2015 Mazda MAZDA3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10194887May 18, 2021Forward collision avoidance, Equipment, Exterior lighting, Lane departure. Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March…
• 10194891May 13, 2021Equipment. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.
• 10194714May 11, 2021Transmission and drivetrain. There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
• 10194659May 7, 2021Electrical system, Equipment, Engine cooling. When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.
• 10194657May 5, 2021Equipment, Electrical system, Engine cooling. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
• 10194762May 4, 2021Equipment. Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method
• 10191538Apr 26, 2021Equipment. APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay™ / Android Auto™, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions
• 10190954Apr 16, 2021Equipment, Electrical system. This service information provides basic Q-85/T-110 battery handling procedures. Complete service information can be found in MGSS online or Workshop Manual (section 13-17).
• 10190971Apr 8, 2021Equipment. MAZDA CONNECT Symptom Troubleshooting (6th Generation Vehicles). Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10213453Mar 16, 2021Visibility (wipers, defrost, mirrors). Mazda connect "no signal" message in reverse
• 10213447Mar 16, 2021Back-over prevention (rear camera), Fuel system, Brakes. MIL ON WITH DTC PO451 AND/OR PO12A Some customer s may complain about a MIL ON with DTC P0451 (Fuel tank pressure sensorL sensor characteristic malfunction) and/or P013A (HO2S: Slow response (during transition from rich to lean)) Recall 8615J repair procedure may correct this concern
• 10189797Mar 15, 2021Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
• 10189816Mar 12, 2021Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10189952Mar 1, 2021Equipment. Service reactivation and owner loyalty program (csp10) - expires april 30, 2021
• 10188086Feb 10, 2021Engine cooling, Wheels. Service reactivation and owner loyalty program (csp10) - expires april 30, 2021
• 10188016Feb 8, 2021Electrical system. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10188015Feb 8, 2021Electrical system. The Mazda DCA-8000PM is required for all warranty battery testing. If the Mazda DCA-8000PM is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10186701Jan 26, 2021Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is…
• 10186699Jan 26, 2021Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road.
• 10186696Jan 26, 2021Engine cooling, Electrical system, Equipment. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem. P2507:00: PCM battery voltage low input
• 10186703Jan 21, 2021Electrical system, Vehicle speed control, Equipment. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
• 10186698Jan 21, 2021Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10186693Jan 21, 2021Steering, Transmission and drivetrain, Wheels, Engine cooling. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10185181Dec 14, 2020Equipment. In order to ensure key code security, MNAO has restricted key code access for the new auxiliary key. This Service Alert provides information on how to obtain the 10-digit key code needed for cutting a new auxiliary key blank if all auxiliary keys are lost.
• 10185049Dec 3, 2020Steering, Equipment. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10183607Nov 18, 2020Equipment, Electrical system. Some customers may complain about the following MAZDA CONNECT™ Temperature Warning message:  Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT™ screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
• 10183601Nov 17, 2020Equipment, Electrical system. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.
• 10183604Nov 10, 2020Engine cooling. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after…
• 10183592Nov 3, 2020Transmission and drivetrain. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise:  Depends on the vehicle’s speed only (the more speed, the more noise)  Occurs with all types of driving (acceleration, deceleration, steady speed)  Does not depend on rpm, gear, or ATF temperature
• 10182123Oct 28, 2020Equipment, Engine cooling. Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H
• 10182130Oct 21, 2020Equipment. MAZDA CONNECT TOUCH SCREEN CONCERN WARRANTY EXTENSION SPECIAL SERVICE PROGRAM: Mazda Motor Corporation is extending the warranty coverage for a specific concern regarding the Mazda Connect Center Display on certain 2014-2016 Mazda3 vehicles produced from June 11, 2013 through September 3, 2016. Please refer to the Parts and Warranty page for specific production date ranges for MC and MMVO produced vehicles as they…
• 10182122Oct 15, 2020Equipment, Electrical system. APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions
• 10180668Sep 21, 2020Visibility (wipers, defrost, mirrors), Equipment, Back-over prevention (rear…. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
• 10180667Sep 15, 2020Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later).
• 10179079Aug 21, 2020Engine cooling. Some customers may complain about an unusual noise coming from the engine compartment for about 20 seconds after a cold engine start. This noise is a normal engine operation for improved exhaust gas emissions. The noise does not indicate a malfunction. ACCELERATED WARM-UP SYSTEM (AWS): All SKYACTIV-G engines adopt AWS to reduce exhaust gas emissions immediately after a cold engine start.
• 10179315Aug 18, 2020Electrical system. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
• 10179228Aug 3, 2020Wheels, Tires. New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
• 10177850Jul 28, 2020Visibility (wipers, defrost, mirrors), Electrical system. Some customer's may complain that the front power window(s) do not operate after the vehicle has been parked outside during freezing temperatures. This may be caused by water that infiltrates into the power window regulator and freezes in the drum groove for the cable. Then when the power window is operated, the cable slips out from the ice-filled groove and tangles, blocking further window operations.
• 10177847Jul 20, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10177844Jul 17, 2020Transmission and drivetrain. Some vehicles may exhibit one of the following concerns:  Sometimes the shifter may jump out of 3rd gear over a road bump when accelerating after deceleration at 25-40 mph (40-65 km/h)  Hard to shift into 3rd, 4th, 5th, and/or 6th gear  Shift lever vibrates when driving in 3rd or 4th gear. This is caused by inappropriate transmission internal parts.
• 10177853Jul 15, 2020Equipment, Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10177843Jul 9, 2020Engine, Equipment, Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been…
• 10177005Jun 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10177012Jun 10, 2020Transmission and drivetrain. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order…
• 10176977Jun 3, 2020Equipment, Electrical system. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the…
• 10174583Apr 17, 2020Electrical system, Equipment. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the…
• 10174650Apr 8, 2020Equipment. Some customers may complain about a rear view monitor display that is:  Blank (or may have backup camera warning message) Distorted Blurry Fuzzy  Split screen (see attached video) Grainy. The icons and text are normally displayed.
• 10174570Apr 1, 2020Steering. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of…
• 10173097Mar 12, 2020Transmission and drivetrain, Equipment, Brakes, Engine cooling. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10173253Mar 11, 2020Equipment, Electrical system. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.

← All problems reported for the 2015 Mazda MAZDA3