2016 Mazda MAZDA3 Technical Service Bulletins

667 technical service bulletins (TSBs) are on record for the 2016 Mazda MAZDA3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10105523Oct 7, 2015Electrical system, Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10105519Oct 7, 2015Brakes. Some vehicles may exhibit a squeak noise when applying the brakes and/or groove marks (a) on the front disc plates. This is caused by abrasive metal from the front disc plate sticking to the brake pad, which damages the disc plate over time. To correct the problem, a modified brake pad is being used.
• 10101459Sep 28, 2015Equipment, Engine. Some vehicles may experience a rough idle with the mil on and dtc p0015 / p0524 stored in memory. • p0015:00 - exhaust cmp timing over-retarded • p0524:00 - engine oil pressure too low this is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or ocv. The temporary entry of the foreign object triggers a mil illumination, but rough idle will not be…
• 10101464Sep 22, 2015Equipment. Some vehicles may experience a fuzzy appearance (tiny cracks) around the edge of the active driving display. Replace the active driving display.
• 10101465Sep 16, 2015Brakes. Some vehicles may experience a squeaking/grinding noise from the rear brake even after the brake pedal is released. Upon inspection, the caliper mounting support is corroded and the disc pad is abnormally worn out (a). This is caused by vehicle usage in an area using road salt. The surface of the mounting support may swell from corrosion causing premature disc pad wear and brake noise.to correct the problem, an…
• 10105467Aug 10, 2015Electrical system, Equipment. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (version 55.00.753 or later). • turn -by-turn navigation guidance does not display on on the active driving display (for vehicles with 55.00.750). • every time the navigation is turned on, the vehicle position starts from the location (dealer) where the cmu was updated from version 55.00.650 to 55.00.750. •…
• 10105481Aug 7, 2015Equipment. Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to dag exchange central (mxconnect>parts and accessories>parts>programs>exchange central) for component availability, source of technical support and prior authorization requirement.
• 10105501Aug 6, 2015Engine, Equipment. Some vehicles may experience the check engine light on with dtc p2610 and p2507 stored in memory after engine start and room fuse 15a (a) removed. • p2610:00: instrument cluster internal engine off timer performance problem • p2507:00: pcm battery voltage low input as a past malfunction, the customer will not notice it (no warning light illuminated), but the dtc may be found during a vehicle service. P2507 in this…
• 10099415Jul 24, 2015Equipment. Some vehicles may exhibit a warped rear mudguard with the surface edge (a) visible from outside the vehicle, causing a poor appearance. In the worst case, it could touch the tire and cause a rubbing noise. The deformation is due to product variation.
• 10099417Jul 21, 2015Equipment. Some vehicles using an auxiliary heater (block heater) may experience the check engine light on with dtc p0116:00 or p011a when starting in cold weather below 32 °f (0 °c). • p0116:00: ect sensor no.1 circuit range/performance problem • p011a:00: ect sensor no.1/no.2 performance problem. This is caused by error detection logic of the pcm. To correct the problem, the control logic of the pcm has been changed.
• 10105432May 27, 2015Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10105445May 18, 2015Body and structure. Some vehicles may experience a rattle noise from the front door glass when driving with the window open approx. 1/2 to 4 inches (1 - 10 cm). The rattle noise may be caused by insufficient holding force of the glass run channel. To increase the holding force, the shape of glass run channel has been changed and non-woven pads have been attached to the glass run channel.
• 10099801Apr 24, 2015Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10099684Mar 30, 2015Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10099685Mar 26, 2015Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10099692Mar 10, 2015Equipment. Some vehicles may experience the check engine light and automatic transaxle warning light on with one or more of these dtcs stored in the tcm memory (p0842, p0847, p0872, p0877, p0780). • p0842:00 - oil pressure switch no. 1 (oil pressure switch b) stuck on • p0847:00 - oil pressure switch no. 2 (oil pressure switch a) stuck on • p0872:00 - oil pressure switch no. 3 (oil pressure switch a) stuck on • p0877:00 - oil…
• 10098863Oct 17, 2014Equipment. Some vehicles may experience mil illumination with dtc p2610 (instrument cluster internal engine off timer performance problem) stored in memory after engine start and room fuse 15a (a) removed. Note:the odometer will display “f0-002” during transport mode (room fuse 15a removed). Transport mode is canceled when room fuse 15a is installed or the vehicle odometer is more than 12.4mi (20km).

← All problems reported for the 2016 Mazda MAZDA3