2018 Mazda MAZDA3 Technical Service Bulletins

462 technical service bulletins (TSBs) are on record for the 2018 Mazda MAZDA3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11007029Aug 26, 2024Electrical system. For improvement of electrical diagnosis, the SKYACTIV® Wiring Terminal Test Kits has been delivered all the dealers. The terminal test kit enables you: To check pin fit drag of all PCM terminals used in SKYACTIV® vehicles and compare suspect terminal drag with a known good terminal. To measure the voltage/resistance avoiding any terminal damage.
• 11007009Aug 21, 2024Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11007022Aug 15, 2024Body and structure. Some vehicles may experience exterior trim heat damage such (melted, separating, etc.) when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 11007019Aug 15, 2024Other or unknown, Electrical system, Engine. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 11007018Aug 13, 2024Body and structure. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply…
• 11007013Aug 12, 2024Other or unknown. Auxiliary key blank cutting procedure. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 11006987Aug 8, 2024Other or unknown, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 11007010Aug 7, 2024Transmission and drivetrain, Engine. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a repair, or just to clean the area and monitor it at the next service.
• 11006917Aug 6, 2024Other or unknown, Body and structure, Electrical system. Some customers may complain that their liftgate does not open. This can mean a range of things, from the liftgate not unlatching to the power liftgate (PLG) not opening automatically. If you confirm that the customer's concern is that the liftgate does not unlatch correctly, follow the repair information below.
• 11006998Aug 5, 2024Other or unknown, Electrical system. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 11005671Jul 29, 2024Other or unknown. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003351Jun 12, 2024Engine. Some customers may experience a check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: Engine takes longer to warm up. Engine temperature gauge fluctuates. Low coolant temperature indicator (blue) light stays on longer or turns on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable to this service…
• 11003398Jun 7, 2024Other or unknown. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 11003397Jun 7, 2024Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 11003396Jun 7, 2024Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 11000775Jun 1, 2024Engine. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 11000772Jun 1, 2024Other or unknown. Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 11000785May 22, 2024Electrical system. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code. NOTE: A Warranty Code is required for warranty claim submission
• 10254187Apr 26, 2024Other or unknown, Equipment. Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
• 10254188Apr 22, 2024Other or unknown, Electrical system. Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10 °C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced at the supplier.
• 10254191Apr 10, 2024Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 10252508Mar 8, 2024Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10252507Mar 6, 2024Transmission and drivetrain. Due to limitations, certain vehicles from 2016 to current models might display an inaccurate transmission part number in the Global Electronic Parts Catalog (GEPC). To provide support in such cases, a temporary lookup guide has been developed for assistance.
• 10251387Feb 12, 2024Brakes, Steering, Transmission and drivetrain, Wheels, Tires, Engine cooling. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10251368Feb 6, 2024Equipment, Electrical system. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10248392Dec 5, 2023Engine cooling. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Alert is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10246121Nov 7, 2023Electrical system, Equipment. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10244679Oct 11, 2023Equipment, Electrical system, Engine cooling. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 10243551Sep 22, 2023Back-over prevention (rear camera), Equipment. Service bulletin 09-031/20 issued on 09/21/20 is no longer valid. It is superceded by recall 6023g (ã¢â€âœ2014-2018 mazda3 and 2016-2021 cx-3 - rearview image may not display properlyã¢â€â).
• 10243568Sep 15, 2023Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10243569Sep 13, 2023Visibility (wipers, defrost, mirrors), Body and structure. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 10241637Aug 28, 2023Electrical system. Some customers may complain about scratches on the instrument cluster lens.
• 10240431Jul 27, 2023Visibility (wipers, defrost, mirrors), Equipment. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
• 10240427Jul 19, 2023Equipment, Visibility (wipers, defrost, mirrors). Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
• 10240496Jul 6, 2023Body and structure. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 10238697Jun 5, 2023Equipment, Body and structure. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply…
• 10238663Jun 5, 2023Engine cooling. Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
• 10238695Jun 1, 2023Engine cooling. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10237217May 24, 2023Electrical system. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10237216May 24, 2023Engine cooling, Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
• 10237215May 17, 2023Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 10237199May 17, 2023Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738).
• 10237197May 9, 2023Electrical system. The Mazda DCA-8000 is required for all warranty battery testing. If the Mazda DCA-8000 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10235414Apr 3, 2023Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10233669Mar 21, 2023Equipment. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
• 10233704Mar 1, 2023Visibility (wipers, defrost, mirrors). Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
• 10232299Feb 28, 2023Electrical system. Speedometer replacement procedure
• 10232304Feb 9, 2023Electrical system, Exterior lighting, Engine cooling, Brakes, Visibility…. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.
• 10232305Feb 6, 2023Body and structure. Due to a supplier change in Dec 2022, bonnet part number BHY0-52-31XA (with seam sealer) will be discontinued and replaced by new part number BAY0-52-31X which does not contain seam sealer. Seam sealer will need to be applied when the hood is being replaced at a collision center/service center.
• 10232300Feb 1, 2023Electrical system. Some customers may complain that the ambient temperature on the instrument cluster is displayed more than 50 °F (10°C) lower than the actual temperature, resulting in insufficient performance of the air conditioning. This is caused by inappropriate soldering in the ambient temperature sensor. To eliminate this concern, the soldering process has been enhanced since December 2021 at the supplier.

← All problems reported for the 2018 Mazda MAZDA3