2013 Nissan Altima Technical Service Bulletins

370 technical service bulletins (TSBs) are on record for the 2013 Nissan Altima. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10075094Dec 22, 2015Electrical system. Summary to be provided on a future date.
• 10074573Dec 22, 2015Exterior lighting. Summary to be provided on a future date.
• 10192707Dec 17, 2015Electrical system. SERVICE INFORMATION The Intelligent Keys used on the various Nissan vehicles may not be interchangeable between models and years. See this bulletin for further detail.
• 10192687Nov 20, 2015Electrical system. SERVICE INFORMATION Design and process changes have been made to improve battery voltage at dealer receipt. Our goal is to deliver vehicles to customers with a 12 volt battery in excellent condition. Proper dealership storage and maintenance of vehicle 12 volt batteries is essential to insuring good battery operating life and customer satisfaction. Dealers are responsible for maintaining vehicles in their inventory.
• 10192679Nov 16, 2015Visibility (wipers, defrost, mirrors). SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be…
• 10192677Nov 16, 2015Visibility (wipers, defrost, mirrors). SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
• 10074569Nov 11, 2015Equipment. Summary to be provided on a future date.
• 10192663Oct 30, 2015Seat belts, Brakes, Vehicle speed control. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter).
• 10192661Oct 27, 2015Equipment. SERVICE INFORMATION: The Navigation (NAVI) SD Map Data Cards are not interchangeable between the two versions of NAVI units offered in Nissan vehicles that use this type of map data. * If the wrong SD Map Data Card is used, the NAVI will display an update screen (Figures 1 and 2, reference only) and will only accept Cancel. * If this screen is displayed, install the correct SD Map Data Card, found in table A on…
• 10192650Oct 8, 2015Electrical system, Equipment. IF YOU CONFIRM The customer states HomeLink will not operate or has improper operation. ACTIONS 1. To significantly reduce unnecessary repairs, make sure: a. The vehicle is not in "Transit Mode" (if equipped). - Not in Transit Mode: With the turn signal switch is in the OFF (center) position, turn the ignition from OFF to ON. If the turn signal indicators stay OFF (do not illuminate), the vehicle is not in Transit…
• 10192645Sep 23, 2015Transmission and drivetrain. IF YOU CONFIRM: The customer reports a transmission judder (shake, shudder, single or multiple bumps or vibration). NOTE: A new diagnostic logic has been established to enhance the diagnostic process by storing diagnostic trouble codes (DTCs) on applied vehicles. These new DTC?s are: P17F1 (CVT_JUDDER (C/U INSPECTION)) P17F0 (CVT_JUDDER (T/M INSPECTION)) ACTION: 1. Refer to step 6 and TABLE A on page 4 in the…
• 10192643Sep 18, 2015Electrical system. IF YOU CONFIRM All of the following - The engine will not start (no crank; starter will not engage) when pushing the ignition switch, and I-Key Error message is displayed in the combination meter, and DTC B2604 (PNP/Clutch Switch) is stored, past or present. ACTION Perform adjustment of the shift control cable per the Service Procedure in this bulletin. See this bulletin for further detail.
• 10192638Sep 15, 2015Brakes, Lane departure, Back-over prevention (rear camera), Wheels. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with…
• 10192615Aug 6, 2015Transmission and drivetrain. SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair.
• 10192614Aug 6, 2015Equipment. SERVICE INFORMATION If the AV Control Unit needs to be replaced on an Applied Vehicle for any reason, follow the steps in the Service Procedure to configure the Multi AV system. NOTE - The original AV Control Unit must be installed in the vehicle while performing part of this procedure. DO NOT remove the original AV Control Unit until instructed. See this bulletin for further detail.
• 10192608Jul 21, 2015Equipment. SERVICE INFORMATION For the Applied Vehicles in this bulletin, when an ABS Actuator and Electric Unit (ABS control unit) is replaced for any reason, Configuration of the ABS Control Unit must be performed. If Configuration is not performed, DTC C1170 (VARIANT CODING) will be stored. The Service Procedure in this bulletin contains the steps for performing ABS Control Unit Manual Configuration. See this bulletin for…
• 10057133Jul 21, 2015Brakes. Nissan: 2013-2015 altima, murano, rogue(t32). Configuration must be performed on the selected vehicles when an abs control unit is being replaced. *lj updated 9/10/15.
• 10192605Jul 10, 2015Wheels, Equipment, Transmission and drivetrain, Back-over prevention (rear…. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and…
• 10192597Jul 6, 2015Steering, Brakes, Back-over prevention (rear camera), Wheels, Equipment. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
• 10192591Jun 24, 2015Engine cooling. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for…
• 10192574May 7, 2015Wheels. SERVICE INFORMATION The appearance of painted alloy wheels can be damaged if acidic cleaners are used. DO NOT use Chrome Wheel Cleaner on Painted Wheels. Many chrome wheel cleaners have acidic ingredients. Make sure to follow all instruction in the Appearance and Care Section of the Owner?s Manual. Damage to wheel appearance due to the use of inappropriate chemicals or cleaning products is not covered under…
• 10192552Apr 2, 2015Electronic stability control, Suspension, Wheels. SERVICE INFORMATION Some of the wheel alignment specifications listed in the Front Suspension (FSU) and Rear Suspension (RSU) sections of the 2013-2015 Altima Sedan Electronic Service Manuals are incorrect. Updated Electronic Service Manuals will be distributed to the field as quickly as possible. Until the updated ESMs are made available, please use the updated service information hyperlinked in this bulletin.
• 10192542Mar 16, 2015Wheels. SERVICE INFORMATION For vehicles delivered to the dealers with wheel protector covers - Do not remove the wheel protector covers during Pre-Delivery Inspection (PDI) - Wheel protector covers help prevent cosmetic rotor corrosion. See this bulletin for further detail.
• 10192532Mar 11, 2015Equipment. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle.
• 10192524Feb 6, 2015Steering, Transmission and drivetrain. SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
• 10192520Jan 29, 2015Back-over prevention (rear camera). IF YOU CONFIRM The MIL is ON with DTC P0101 for Mass Air Flow sensor (MAF) stored in the ECM, AND there are no drivability concerns. ACTION 1. Refer to step 6 in the SERVICE PROCEDURE to confirm this bulletin applies to the vehicle you are working on. 2. If this bulletin applies, reprogram the ECM. See this bulletin for further detail.
• 10192513Jan 16, 2015Equipment, Air bags, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192508Jan 15, 2015Equipment. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the…
• 10192491Dec 15, 2014Body and structure. SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ----- Page 2 - Two (2) Intelligent Keys Are Lost ----- Page 3 See this bulletin for further detail.
• 10192486Dec 2, 2014Electrical system, Air bags, Equipment. SERVICE INFORMATION The OCS (Occupant Classification System) sensors for the Applied Vehicles are now available as service parts. See this bulletin for further detail.
• 10192478Nov 25, 2014Electrical system, Engine. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM).
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10192471Nov 19, 2014Body and structure, Engine. SERVICE INFORMATION A two-piece design front engine mount is currently being used for the applied vehicles listed. A single thunk noise may be heard on the first acceleration of the day from this type of mount and is considered normal operation. The mount has also been designed with built in free-play that is normal. Under normal driving conditions: * A "thunk" noise may be heard on the first acceleration of the…
• 10192464Nov 7, 2014Engine, Engine cooling. Nissan is conducting an inventory inspection on 105,290 specific MY2013-15 Nissan ALT, PTH, LEF, MUR, NV2, NVT, SEN, and VER NOTE vehicles to inspect the software on the OCS ECU.
• 10192436Sep 4, 2014Equipment, Body and structure, Visibility (wipers, defrost, mirrors). IF YOU CONFIRM A squeaking/ticking noise is coming from the Headliner between the Moonroof and B-pillar area shown in Figure A. * Can occur on rough roads or during conditions that cause body flex such as when entering or exiting a sloped driveway. ACTION Remove Moonroof brackets and apply UHMW tape, from Squeak and Rattle kit J-50397 (part # J-50397-15), to the bracket. Please see this bulletin for further details.
• 10056181Aug 29, 2014Equipment. Nissan: regarding some vehicles using two stain gauge occupant classification system (ocs) operation, and the pressures necessary due to different response of occupant seating posture. Model 2013-2015 altima, sentra, pathfinder, leaf, nv200, nv200 taxi, rogue.
• 10192422Aug 18, 2014Equipment, Transmission and drivetrain. SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: NISSAN recommends using Genuine NISSAN NS-3 CVT…
• 10192421Aug 18, 2014Equipment, Transmission and drivetrain. SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service…
• 10192394Jun 24, 2014Electrical system, Equipment. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10192378May 30, 2014Brakes, Equipment. IF YOU CONFIRM A squeal/squeak noise is coming from the rear brakes: - When the brakes are either hot (after 10-15 minutes of driving) or cold (after vehicle has not been driven for 2-3 hours), - while moving forward or in reverse, - at speeds less than 10 MPH, - while traveling straight, AND - with light to moderate brake application (pedal pressure).
• 10192377May 30, 2014Equipment, Electrical system. IF YOU CONFIRM: The customer states the following: - While driving, the audio setting in the Vehicle Information Display (VID) is blank while displaying normally in the audio unit. - All other items in the VID display normally i.e. temperature, MPG, etc. - Items above and below the VID display normally i.e. DTE, gear selection, etc. - The issue occurs with the ignition ON or the engine running. - The audio setting…
• 10192372May 21, 2014Steering, Electrical system, Transmission and drivetrain. IF YOU CONFIRM: The customer is experiencing a noise coming from the passenger side engine compartment and The source of the noise is confirmed to be the Hydraulic Electric Power Steering (H-EPS) and The noise is louder than the normal operational noise of the H-EPS. Notes: - Some operational noise from the front of the vehicle generated by the H-EPS is normal when the steering wheel is operated.
• 10192370May 19, 2014Body and structure, Equipment. SERVICE INFORMATION - The Applied Vehicles are equipped with a hood ledge finisher on the passenger (RH) side only. - Do not submit a claim for a "missing" hood ledge finisher on driver's (LH) side. See this bulletin for further detail.
• 10192361May 6, 2014Equipment, Electrical system. SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s…
• 10192354Apr 29, 2014Electrical system. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
• 10192340Mar 27, 2014Equipment, Engine cooling. SERVICE INFORMATION The base model of the 2013-2014 Altima 2.5 Sedan is not equipped with an engine cover. Base model 2013 Altima 2.5 Sedan vehicles built before the VINs and dates shown below are not equipped with exhaust finishers. 1N4AL3AP(*)DC 227196 // March 13, 2013 1N4AL3AP(*)DN 530748 // March 8, 2013 The base model can be identified by the model designation on the trunk lid.
• 10192328Feb 25, 2014Engine, Transmission and drivetrain. IF YOU CONFIRM: When slowly raising the engine RPM, a hissing, whining, and/or air leak type noise of an applied vehicle is heard coming from the driver side lower instrument panel area. - The noise is verified while the vehicle is parked and the transmission is in the Park (P) position. NOTE: A customer may state the noise can be duplicated during light to moderate acceleration in the 10 - 40 MPH range. ACTION: 1.
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192298Jan 24, 2014Visibility (wipers, defrost, mirrors), Equipment. IF YOU CONFIRM: A wind or road type noise is coming from either front door around the door mirror area AND / OR A rattle or flutter type noise is heard from the window or mirror area(s). NOTE: The noises reduce during a road test after applying "painter's tape" or suitable covering where noted in Figure 1. - The rattle noise is coming from the lower cover due to loose fit. ACTION: Refer to the REPAIR FLOW CHART on…
• 10192293Jan 13, 2014Engine, Engine cooling. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.

← All problems reported for the 2013 Nissan Altima