2008 Nissan Frontier Technical Service Bulletins

106 technical service bulletins (TSBs) are on record for the 2008 Nissan Frontier. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192821May 10, 2016Equipment, Transmission and drivetrain. SERVICE INFORMATION Replacement 5-speed rear wheel drive Automatic Transmission (A/T) assemblies and replacement control valves (valve bodies) now come with blank Transmission Control Modules (TCMs). Blank TCMs come without software and must be programmed (not reprogrammed) and then configured after they are installed.
• 10192805Apr 18, 2016Equipment. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further…
• 10192801Apr 13, 2016Equipment, Forward collision avoidance. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail.
• 10192740Feb 19, 2016Fuel system. IF YOU CONFIRM: The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM. ACTION: 1. Replace the EVAP canister (canister) and EVAP canister vent control valve (vent control valve). 2. Remove the canister filter. 3. Attach the EPT foam seal to fuel filler tube. 4. Replace the fuel filler pipe, canister drain hose, and fuel filler cap (on some model years) listed in PARTS INFORMATION…
• 10192727Jan 28, 2016Visibility (wipers, defrost, mirrors). SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due…
• 10192691Nov 30, 2015Transmission and drivetrain. IF YOU CONFIRM: A remanufactured automatic transmission supplied by ATC Drivetrain is installed in an APPLIED VEHICLE AND CONSULT-III plus (C-III plus) is not able to communicate with the TCM through Diagnosis (One System) OR C-III plus is able to communicate with the TCM, but the TCM part number?s (P/N) sixth digit is a "5", "6", or "7" (for example, 31020-7xxxx). NOTE: To determine if an applied vehicle is…
• 10192679Nov 16, 2015Visibility (wipers, defrost, mirrors). SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be…
• 10192677Nov 16, 2015Visibility (wipers, defrost, mirrors). SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details.
• 10192638Sep 15, 2015Brakes, Lane departure, Back-over prevention (rear camera), Wheels. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with…
• 10192597Jul 6, 2015Steering, Brakes, Back-over prevention (rear camera), Wheels, Equipment. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
• 10192591Jun 24, 2015Engine cooling. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for…
• 10192524Feb 6, 2015Steering, Transmission and drivetrain. SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail.
• 10192513Jan 16, 2015Equipment, Air bags, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192508Jan 15, 2015Equipment. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the…
• 10192506Jan 8, 2015Back-over prevention (rear camera), Air bags. IF YOU CONFIRM: Squeal/Squeak noise from the front brakes: While moving forward or reverse, with very light brake application (pedal pressure), after the vehicle has been sitting, typically overnight ("cold" brakes), at speeds less than 10 MPH, while traveling straight or turning. ACTION: Replace the hardware on both front brake calipers with the kit listed in the Parts Information in this bulletin. See this…
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10192394Jun 24, 2014Electrical system, Equipment. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10192326Feb 19, 2014Equipment. SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not…
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10025522Jan 27, 2014Air bags. Nissan: srs precautions during service;improper maintenance, including incorrect removal and installation of the srs, can lead to a serious injury or death caused by unintentional activation of the srs on all nissan models with the srs systems. *pe updated 2/21/14.
• 10032306Nov 27, 2013Exterior lighting. Nissan: exterior lamp fogging. Occasionally water is noticed in the exterior lamps. This is generally not due to a defect. All current exterior lamp assemblies are vented to the atmosphere (not sealed). This is necessary to allow for expansion and contraction of air from temperature variations (warmer or colder) without damage to the lamp. Moisture in the air sometimes travels into and out of the lamp assembly…
• 10192266Nov 15, 2013Fuel system, Equipment. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >>…
• 10053956Nov 15, 2013Fuel system. Nissan: a loose fuel fill cap is the cause of evap leak dtcs (p0442, p0455, p0456) stored on some vehicles. Model years 2007-2011. Model not listed.
• 10192233Aug 27, 2013Equipment, Wheels. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming…
• 10025645Aug 27, 2013Wheels. Aftermarket chroming of nissan alloy wheels not approved or authorized and strongly discouraged. All models including 2008-2009 my. *pe updated 1/31/14.
• 10192231Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
• 10192217Jul 23, 2013Wheels, Steering, Brakes. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192216Jul 23, 2013Suspension, Steering, Brakes, Wheels. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192192Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10051767Apr 3, 2013Latches, locks and linkages. Nissan: lock/unlock request button on outside handle does not respond.
• 10192145Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192127Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192051Oct 12, 2012Transmission and drivetrain. Nissan has decided in the interest of customer satisfaction, to further extend the warranty for the Radiator Assembly on all 2005-10 Frontier, Pathfinder, and Xterra vehicles equipped with automatic transmissions.
• 10046601Sep 25, 2012Brakes. Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. Model 2007-2013 nissan.
• 10043950Apr 10, 2012Transmission and drivetrain. Nissan: ecm replacement procedures with consult iii plus. Applies to all 2004 and later (does not apply to leaf/ev) vehicles.
• 10043771Mar 22, 2012Steering. Nissan: pathfinder, xterra, and frontier; power steering hose service part change.
• 10043735Feb 3, 2012Latches, locks and linkages, Other or unknown. Nissan: door lock/unlock inoperative with intelligent key.
• 10032627Nov 30, 2010Fuel system. Nissan: fuel gauge issues and/or dtc p0461/2/3. The fuel gauge is erratic, inaccurate, or inoperative. The mil is on with dtc p0461, p0462, or p0463 stored in self diagnosis. Replace the fuel level sending unit with the one from the parts information section. *pe updated 1/24/11. *pe amendment updated. 2/28/11.
• 10034904Oct 6, 2010Suspension. Nissan: front suspension noise. A noise (clunking, squeaking, popping) can be heard when performing at least one of the following actions: turning the steering wheel left or right, driving over speed bumps, driving on rough roads, accelerating or decelerating and noise is coming from the front stabilizer bar bushing.
• 10031305Sep 30, 2010Tires. Nissan: tire pressure monitoring system (tpms) warning light on/flashing. No models or model years listed. *pe updated on 08-11-2011.
• 10034871Sep 27, 2010Steering. Nissan: power steering oil cooler service. If a power steering oil cooler needs to be replaced for any reason, please refer to the service procedure.
• 10032506Sep 13, 2010Equipment. Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (d40 series) only, install the protector listed in parts information. *pe includes…
• 10033691May 10, 2010Engine cooling. Nissan: engine coolant temperature sensor circuit range/performance is stored in the ecm and there are no other vehicle drivability symptoms.
• 10032992Apr 27, 2010Exterior lighting. Nissan: xenon head lamp service. A xenon headlamp is not functioning because of an issue inside the headlamp assembly (an internal issue). In most cases, replacement of a bulb or hid control unit will solve the incident. This includes all models with xenon head lamps. No models listed.
• 10033710Apr 20, 2010Engine cooling, Equipment. Nissan: blower motor does not work. The blower motor for heater and air conditioner does not operate. There are signs of water intrusion in the blower motor.
• 10033306Jan 15, 2010Suspension. Nissan: rear axle seal leaks. The rear axle assembly is leaking gear oil from the right and/or left hand axle seal, and the vehicle is equipped with a m226 style axle and no noise or vibration is coming from the rear final drive gears and side bearings.
• 10025504Oct 22, 2009Equipment. Nissan service campaign: see document search button for owner letter. Voluntary service campaign for 2008 frontier king cab le and nismo models with technology package. Install the vehicle security system and the vehicle immobilizer system. *pe updated 12/23/08. Csc letter was received. *pe updated 1/13/10.
• 10031124Oct 5, 2009Brakes, Steering, Electrical system. Nissan: the following dtc codes are stored c1143 (steering angle sensor) and/or c1163 (st angle sen safe). Reprogram the abs/vdc control unit software.
• 10030165Apr 6, 2009Electrical system. Nissan: the 12 volt battery is an important part of the vehicle electrical system and is required to stay connected when the engine is running. To prevent damage to vehicle electronic components follow the instructions/cautions. No model years listed.
• 10026796Oct 23, 2008Exterior lighting. Nissan: left turn signal not canceling out upon completing a turn.

← All problems reported for the 2008 Nissan Frontier