2009 Nissan Maxima Technical Service Bulletins

99 technical service bulletins (TSBs) are on record for the 2009 Nissan Maxima. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192513Jan 16, 2015Equipment, Air bags, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192508Jan 15, 2015Equipment. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the…
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10192442Sep 16, 2014Electrical system. IF YOU CONFIRM - MIL is on with DTC's P0014 and/or P0024. - Customer describes a hesitation at speeds below 15 MPH after the oil was changed. ACTION Replace left and right cylinder bank's "Exhaust Valve Control Magnet Retarder". Please see this bulletin for further details.
• 10192440Sep 11, 2014Steering, Equipment. SERVICE INFORMATION When replacing the Electronic Steering Column Lock, there are two possible service parts that may be shipped to the dealer: 48700-9N00B or 48700-1NC0A. These part numbers are interchangeable. If you receive Electronic Steering Column Lock P/N 48700-1NC0A, the bolts that hold it in place may not line up. You may not be able to start the bolt threads. If you encounter this condition, see this…
• 10192394Jun 24, 2014Electrical system, Equipment. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10055044Feb 18, 2014Steering. Nissan: with electronic steering column lock, bolts may not line up to hold in place and bolt threads may not be started and a small amount metal from edges is removed by using a hand file.
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192293Jan 13, 2014Engine, Engine cooling. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
• 10192284Dec 17, 2013Engine. IF YOU CONFIRM A knock noise coming from the # 1 crankshaft main bearing: ACTION 1. Remove the # 1 main bearing (upper and lower halves), per the Service Procedure in this bulletin. 2. Select and install a new # 1 main bearing that is one grade higher (thicker) than the one removed. See this bulletin for further detail.
• 10054120Dec 17, 2013Engine. Nissan: knocking noise coming from number 1 crankshaft main bearing, was not heard at cold start, when vehicle is lifted, knocking is heard, or at warm idle, not heard at highway speeds or sitting with radio on. Model 2009-2014 maxima
• 10032306Nov 27, 2013Exterior lighting. Nissan: exterior lamp fogging. Occasionally water is noticed in the exterior lamps. This is generally not due to a defect. All current exterior lamp assemblies are vented to the atmosphere (not sealed). This is necessary to allow for expansion and contraction of air from temperature variations (warmer or colder) without damage to the lamp. Moisture in the air sometimes travels into and out of the lamp assembly…
• 10192266Nov 15, 2013Fuel system, Equipment. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >>…
• 10053956Nov 15, 2013Fuel system. Nissan: a loose fuel fill cap is the cause of evap leak dtcs (p0442, p0455, p0456) stored on some vehicles. Model years 2007-2011. Model not listed.
• 10038184Nov 5, 2013Transmission and drivetrain. Nissan: the vehicle has a slower than normal acceleration from a stop. Updated on 06/08/2011. *kb updated on 06/13/2011. *rm updated 12/16/2013
• 10192234Aug 27, 2013Equipment. Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
• 10192233Aug 27, 2013Equipment, Wheels. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming…
• 10192231Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
• 10192217Jul 23, 2013Wheels, Steering, Brakes. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192216Jul 23, 2013Suspension, Steering, Brakes, Wheels. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192198Jun 17, 2013Air bags, Seats, Wheels, Steering, Electrical system. SERVICE INFORMATION If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle for any reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for more detail.
• 10052396Jun 17, 2013Steering. Nissan: on certain vehicles, the steering wheel switches may need replacing but not the driver air bag module. Models 2009-13 maxima.
• 10192193Jun 7, 2013Suspension, Wheels, Body and structure, Air bags. IF YOU CONFIRM: The front passenger seatback has a greater than normal vibration at highway speeds AND There are no other shake or vibrations with the vehicle. ACTION: Use the REPAIR FLOW CHART on page 3 to determine the repair(s) to be performed. NOTES: - The description under IF YOU CONFIRM must exist for this bulletin to apply. - If determined the passenger seatback frame will be replaced: - The headrest…
• 10192192Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10192181May 17, 2013Equipment. SERVICE INFORMATION The navigation system in the Applied Vehicles has an HDD (Hard Disc Drive) map data storage system. This bulletin contains the information and instructions for updating/upgrading the map data with a new version. See this bulletin for further detail.
• 10192158Apr 4, 2013Electrical system. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
• 10051768Apr 4, 2013Vehicle speed control. Nissan: cruise control will not set and dtc p0605 is stored.
• 10192155Apr 3, 2013Vehicle speed control, Seat belts. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled…
• 10051767Apr 3, 2013Latches, locks and linkages. Nissan: lock/unlock request button on outside handle does not respond.
• 10192145Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192142Mar 15, 2013Seat belts, Steering. Nissan has decided in the interest of customer satisfaction, to extend the warranty for the Electronic Steering Column Lock unit on all 2009 Altima and Maxima vehicles.
• 10192127Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192115Jan 25, 2013Transmission and drivetrain. IF YOU CONFIRM: After having been parked overnight in ambient temperatures between 5°C to -25°C (40°F to -14°F) the vehicle is hard to start or cranks and will not start. And * Occurs only on first attempts to start before engine begins running. And * Will not occur after engine has been started and run for any period of time. ACTIONS: * Confirm this bulletin applies and if so reprogram the ECM. See this bulleitn…
• 10046601Sep 25, 2012Brakes. Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. Model 2007-2013 nissan.
• 10047059Aug 27, 2012Visibility (wipers, defrost, mirrors). Nissan: rain sensors may operate, intermittently or unexpectedly, when exhaust gas, moisture, fingerprints, dirt, or insects are near or around rain sensors. No models or model years listed.
• 10043950Apr 10, 2012Transmission and drivetrain. Nissan: ecm replacement procedures with consult iii plus. Applies to all 2004 and later (does not apply to leaf/ev) vehicles.
• 10043774Mar 22, 2012Steering. Nissan: altima, maxima; power steering hose service part change. The hose now comes without the pressure sensor. Do not damage pressure sensor upon removal or installation. If only the pressure sensor needs to be replaced, do not replace any hoses.
• 10043735Feb 3, 2012Latches, locks and linkages, Other or unknown. Nissan: door lock/unlock inoperative with intelligent key.
• 10040510Aug 24, 2011Suspension. Nissan: axle bolt and torque information.
• 10038552Apr 11, 2011Transmission and drivetrain. Nissan: there is a trouble code stored due to software. Some 2009 vehicles.
• 10032964Mar 22, 2011Equipment, Suspension. Nissan: the mil is on with one or more of the following dtcs stored: p0442/p0448/p0455/p0456 and evap vent control valve is stuck open or will not seal when operated/closed. Replace vent control valve; install filter kit listed in parts information; and clear any dtcs stored in the ecm. *pe updated 6/15/11.
• 10039824Feb 18, 2011Fuel system. Nissan: the fuel guage is erratic, the malfunction light is on, and there are stored trouble codes.
• 10035684Jan 14, 2011Equipment. Nissan: navigation map data update matrix. Affecting all vehicles 2003-11 except leaf, equipped with navigation system. Customer is mailed update disc(s) or sd card and installs data; dealership is mailed update disc(s) and the dealership installs data when vehicle is brought in.
• 10030710Nov 18, 2010Seats. Nissan: the driver's seat bottom very slightly rocks and/or shifts back and forth when accelerationg, braking, or when making a turn. Replace the driver seat frame (adjuster assembly) with a new one. *pe updated 1/24/11.
• 10031305Sep 30, 2010Tires. Nissan: tire pressure monitoring system (tpms) warning light on/flashing. No models or model years listed. *pe updated on 08-11-2011.
• 10032506Sep 13, 2010Equipment. Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (d40 series) only, install the protector listed in parts information. *pe includes…
• 10032992Apr 27, 2010Exterior lighting. Nissan: xenon head lamp service. A xenon headlamp is not functioning because of an issue inside the headlamp assembly (an internal issue). In most cases, replacement of a bulb or hid control unit will solve the incident. This includes all models with xenon head lamps. No models listed.
• 10028566Apr 23, 2009Suspension. Nissan: the left hand rear suspension knuckle may not be manufactured to specification, which may result in noise or vibration under certain circumstances. (sedans, coupes, and hybrids).
• 10030165Apr 6, 2009Electrical system. Nissan: the 12 volt battery is an important part of the vehicle electrical system and is required to stay connected when the engine is running. To prevent damage to vehicle electronic components follow the instructions/cautions. No model years listed.

← All problems reported for the 2009 Nissan Maxima