2010 Nissan Sentra Technical Service Bulletins

103 technical service bulletins (TSBs) are on record for the 2010 Nissan Sentra. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192605Jul 10, 2015Transmission and drivetrain, Wheels, Equipment, Back-over prevention (rear…. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear CV-type axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. - For 2007-2013 Versa and…
• 10192604Jul 9, 2015Back-over prevention (rear camera). IF YOU CONFIRM: The vehicle speed is, or was, reduced by the CVT fail-safe (reduced vehicle speed) after continuous operation under the following conditions: * High RPM and/or high speed driving (4000 RPM or more, and/or 65 MPH or more for 1.0 - 1.5 hrs or more) * Driving in ambient temperature of 96 degrees or higher * Climbing steep or extended hills for 6 miles or more * Whine or rattle type noise occurring…
• 10192597Jul 6, 2015Equipment, Back-over prevention (rear camera), Steering, Brakes, Wheels. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
• 10192591Jun 24, 2015Engine cooling. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for…
• 10192532Mar 11, 2015Equipment. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle.
• 10192513Jan 16, 2015Air bags, Equipment, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192508Jan 15, 2015Equipment. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the…
• 10192478Nov 25, 2014Engine, Electrical system. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM).
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10056188Aug 15, 2014Engine. Nissan: after certain continuous operation and vehicle speed has been reduced due to the fail safe of the cvt, caused by driving in ambient temperature, high rpm and/or high speed, whinnying or rattling noise occurring during reduced engine performance and/or climbing steep or extended hills. Model 2007-2012 sentra.
• 10192394Jun 24, 2014Equipment, Electrical system. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10192354Apr 29, 2014Electrical system. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192293Jan 13, 2014Engine, Engine cooling. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
• 10032306Nov 27, 2013Exterior lighting. Nissan: exterior lamp fogging. Occasionally water is noticed in the exterior lamps. This is generally not due to a defect. All current exterior lamp assemblies are vented to the atmosphere (not sealed). This is necessary to allow for expansion and contraction of air from temperature variations (warmer or colder) without damage to the lamp. Moisture in the air sometimes travels into and out of the lamp assembly…
• 10192266Nov 15, 2013Fuel system, Equipment. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >>…
• 10053956Nov 15, 2013Fuel system. Nissan: a loose fuel fill cap is the cause of evap leak dtcs (p0442, p0455, p0456) stored on some vehicles. Model years 2007-2011. Model not listed.
• 10192259Nov 5, 2013Electrical system, Transmission and drivetrain. IF YOU CONFIRM The vehicle has slower than normal acceleration from a stop at times, and/or the customer describes the vehicle has slower than normal acceleration from a stop at times, and/or The MIL is ON with DTC P1778 (STEP MOTOR) stored in Engine and/or Transmission. and/or Only for Sentra without ABS; MIL is ON with DTC P0720 (OUTPUT SPEED SENSOR) stored in Engine and/or Transmission. ACTIONS 1. Replace the…
• 10036734Nov 5, 2013Engine cooling, Transmission and drivetrain. Nissan: mil is on and/or slower than normal acceleration. Slower than normal acceleration from a stop at times, if it should occur, happens more commonly when the vehicle has been driven for an extended periods at highway speeds. Mil is on with dtc 01778 (step motor) stored in engine and/or transmission and/or dtc p0720 (output speed sensor) stored in engine and/or transmission. *pe updated 12/16/2013
• 10054527Sep 26, 2013Tires. Nissan: information regarding tire pressure monitor system (tpms) and low tire pressure warning system (ltpws) for sensor leaks, air pressure changes with altitude and ambient temperatures, aftermarket wheels, radio frequency interference causing no data condition and inflating/deflating tires with tpms/ltpws sensors. Model all. No models years.
• 10192234Aug 27, 2013Equipment. Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
• 10192233Aug 27, 2013Equipment, Wheels. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming…
• 10192231Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
• 10192217Jul 23, 2013Brakes, Steering, Wheels. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192216Jul 23, 2013Wheels, Brakes, Steering, Suspension. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192196Jun 17, 2013Air bags, Electrical system, Wheels, Seats, Steering. SERVICE INFORMATION If you confirm there is a need to replace the steering wheel switches on an Applied Vehicle for any reason: - Do not replace the driver air bag module. The steering wheel switches are now available as a separate service part. - Refer to the Service Procedure in this bulletin for steering wheel switch removal and installation instructions. See this bulletin for further detail.
• 10052406Jun 17, 2013Steering. Nissan: information provided regarding removal and installation of steering wheel switch service parts, if needed, on certain vehicles. Models 2007-2012 sentra.
• 10192192Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10192158Apr 4, 2013Electrical system. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
• 10051768Apr 4, 2013Vehicle speed control. Nissan: cruise control will not set and dtc p0605 is stored.
• 10192155Apr 3, 2013Vehicle speed control, Seat belts. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled…
• 10051767Apr 3, 2013Latches, locks and linkages. Nissan: lock/unlock request button on outside handle does not respond.
• 10192145Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192127Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192120Feb 1, 2013Equipment. IF YOU CONFIRM Oil is leaking from the upper end of the engine oil cooler. ACTION: Reseal the oil cooler with the parts listed in the PARTS INFORMATION on page 2. - For repairs, refer to REPAIR PROCEDURE starting on page 3. NOTE: Do not replace the complete engine oil cooler assembly for this incident, if it should occur. See this bulletin for further detail.
• 10192077Dec 4, 2012Electrical system, Equipment, Air bags. SERVICE INFORMATION If you confirm there is a need to replace the driver and/or front passenger seat side air bag module in an Applied Vehicle for any reason: * Do not replace the entire seatback assembly if only the side air bag needs to be replaced. The side air bag module is now available as a separate service part. * Refer to the SE section of the applicable Electronic Service Manual (ESM) for seatback…
• 10192061Oct 30, 2012Back-over prevention (rear camera). IF YOU CONFIRM: * "Missing SD card" message appears. * Error message "Communication problem occurred check connection" with iPhone (1st Generation only). Connected through USB and after an incoming call. * No Voice guidance after unit replacement or software update. ACTION: 1. Check the SD card number. * Update SD card if 25920-ZW00A is present. 2. Update NAVI to N603 Software version. 3. Confirm that voice…
• 10046601Sep 25, 2012Brakes. Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. Model 2007-2013 nissan.
• 10047059Aug 27, 2012Visibility (wipers, defrost, mirrors). Nissan: rain sensors may operate, intermittently or unexpectedly, when exhaust gas, moisture, fingerprints, dirt, or insects are near or around rain sensors. No models or model years listed.
• 10044570Jul 6, 2012Transmission and drivetrain. Nissan: if continuously variable transmission (cvt) fluid temperature rises above a certain threshold, it will go into fluid protection logic mode (fail safe mode), as designed.
• 10043950Apr 10, 2012Transmission and drivetrain. Nissan: ecm replacement procedures with consult iii plus. Applies to all 2004 and later (does not apply to leaf/ev) vehicles.
• 10043346Feb 8, 2012Brakes. Nissan: information regarding warning and/or indicator lights coming on for abs and brake with no dtcs found.
• 10043735Feb 3, 2012Other or unknown, Latches, locks and linkages. Nissan: door lock/unlock inoperative with intelligent key.
• 10041392Sep 6, 2011Engine cooling. Nissan: oil is leaking from the upper end of the engine oil cooler.
• 10032965Jun 24, 2011Fuel system. Nissan: fuel gauge issues and/or dtc p0461/p0461/p0462/p0463. The fuel gauge is erratic, inaccurate, or inoperative. The mil is on with dtc stored in self diagnosis. Replace the fuel lever sensor unit. *pe updated on 08-11-2011.
• 10035684Jan 14, 2011Equipment. Nissan: navigation map data update matrix. Affecting all vehicles 2003-11 except leaf, equipped with navigation system. Customer is mailed update disc(s) or sd card and installs data; dealership is mailed update disc(s) and the dealership installs data when vehicle is brought in.
• 10035944Oct 26, 2010Seats. Nissan: head restraint on front seat(s) is loose. Moves back and forth. Detach the seat back finisher and replace the head restraint spring and clip.
• 10031305Sep 30, 2010Tires. Nissan: tire pressure monitoring system (tpms) warning light on/flashing. No models or model years listed. *pe updated on 08-11-2011.
• 10032506Sep 13, 2010Equipment. Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (d40 series) only, install the protector listed in parts information. *pe includes…
• 10034677Sep 3, 2010Transmission and drivetrain. Nissan: the clutch pedal spring needs to be replaced for any reason (such as noise). Replace the spring and bushings with the ones listed in parts information section. Do not replace the entire clutch pedal assembly if only replacing the spring is necessary.

← All problems reported for the 2010 Nissan Sentra