2013 Nissan Sentra Technical Service Bulletins

201 technical service bulletins (TSBs) are on record for the 2013 Nissan Sentra. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192532Mar 11, 2015Equipment. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle.
• 10192513Jan 16, 2015Equipment, Air bags, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192508Jan 15, 2015Equipment. SERVICE INFORMATION DTC B2190 (NATS ANTENNA AMP) can be stored for the following reasons: 1. Something other than an Intelligent Key is inserted into the Key-Slot. 2. An Intelligent Key issue. 3. A wiring issue between the Key-Slot and the BCM. 4. A Key-Slot issue. If DTC B2190 is stored due to 1 or 2 above, it will not erase, or go to "PAST", until a known good registered Intelligent Key is inserted into the…
• 10057131Dec 17, 2014Engine. Nissan: 2013-2014 sentra : 2013 models are equipped with an upper torque rod. 2014 models sv, sl & sr does not have an upper torque rod.
• 10192486Dec 2, 2014Electrical system, Air bags, Equipment. SERVICE INFORMATION The OCS (Occupant Classification System) sensors for the Applied Vehicles are now available as service parts. See this bulletin for further detail.
• 10192478Nov 25, 2014Electrical system, Engine. SERVICE INFORMATION Starting with 2010 Model Year, Nissan vehicles have been gradually incorporating a new type of DTC known as Permanent DTC or P-DTC. If a vehicle is equipped with P-DTCs, all emission related DTCs will also set a P-DTC if the MIL is turned ON. A listing of which DTCs that will also set a P-DTC is found in the DTC Index in the EC-Engine Control section of the Electronic Service Manual (ESM).
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10192464Nov 7, 2014Engine, Engine cooling. Nissan is conducting an inventory inspection on 105,290 specific MY2013-15 Nissan ALT, PTH, LEF, MUR, NV2, NVT, SEN, and VER NOTE vehicles to inspect the software on the OCS ECU.
• 10056181Aug 29, 2014Equipment. Nissan: regarding some vehicles using two stain gauge occupant classification system (ocs) operation, and the pressures necessary due to different response of occupant seating posture. Model 2013-2015 altima, sentra, pathfinder, leaf, nv200, nv200 taxi, rogue.
• 10192422Aug 18, 2014Equipment, Transmission and drivetrain. SERVICE INFORMATION The purpose of this bulletin is to clarify language contained in the owner?s manual language for the APPLIED VEHICLES. For the APPLIED VEHICLES, the below language supersedes similar language in existing owner?s manuals. Future printings of owner?s manuals for the APPLIED VEHICLES will also contain the below language. For the APPLIED VEHICLES: NISSAN recommends using Genuine NISSAN NS-3 CVT…
• 10192421Aug 18, 2014Equipment, Transmission and drivetrain. SERVICE INFORMATION Applied vehicles equipped with a CVT have a "cap" that appears to be a fluid level gauge. This "cap" will NOT have a gauge or "dipstick". This is normal. Do NOT replace the "cap" because it is thought to have a "dipstick". The fluid level is not checked from this location. The fluid level for applied vehicles is checked from the oil pan (refer to the appropriate section of the Electronic Service…
• 10192417Aug 7, 2014Electrical system, Engine cooling. IF YOU CONFIRM: The engine will not start (the starter does not operate) AND Any of the following DTCs are found stored: P1650, P1651, B210C Combined with one or more of the following DTCs: B2562, B00A0, B142A, C1601 ACTION: 1) Test the battery with the GR8 Multitasking Battery Diagnostic Station (battery tester/charger). 2) Reprogram the ECM using CONSULT-III plus, and then confirm: The starter operates, the…
• 10192394Jun 24, 2014Electrical system, Equipment. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10055835Jun 4, 2014Engine. Nissan: vehicle's engine has a no crank or fails to start, with diagnostic trouble codes, b210c (starter control relay off), p1650 (starter motor relay 2), or p1651 (starter motor relay). Model 2013-2014 sentra.
• 10192369May 16, 2014Equipment, Fuel system. IF YOU CONFIRM The MIL is ON with DTC P0448 (Vent Control Valve). ACTION 1. Reposition the EVAP canister box-drain. 2. Empty water from the EVAP canister filter. See this bulletin for further detail.
• 10192368May 14, 2014Seats, Equipment. SERVICE INFORMATION If a Seat Cushion Outer Finisher needs to be removed for any reason, make sure to follow the instructions in this bulletin.
• 10192354Apr 29, 2014Electrical system. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
• 10192306Jan 27, 2014Electrical system, Engine. IF YOU CONFIRM: The engine RPM intermittently drops very low while stopped (idling) or the engine stops running while coming to a stop. NOTE: These symptoms can occur under the following conditions. - Low engine RPM at idle while the A/C is off and without any electrical load from the alternator - The engine speed (RPM) becomes low while coming to a stop with the A/C on - The engine stops running when coming to a…
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10052250Jan 27, 2014Engine, Electrical system. Nissan: while vehicle is stopped and idling, engine's rpm would drop, intermittently, and was not caused by an electrical overload of alternator or by a/c compressor, and needs to be checked and if necessary, ecm reprogram. Model 2013-2014 sentra. *pe updated 12/18/13. *pe updated 2/21/14.
• 10192293Jan 13, 2014Engine, Engine cooling. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
• 10053958Nov 15, 2013Fuel system. Nissan: certain vehicles would display, in the instrument cluster, a warning light illumination of a loose fuel cap warning. Model years 2012-2014. No models listed.
• 10054527Sep 26, 2013Tires. Nissan: information regarding tire pressure monitor system (tpms) and low tire pressure warning system (ltpws) for sensor leaks, air pressure changes with altitude and ambient temperatures, aftermarket wheels, radio frequency interference causing no data condition and inflating/deflating tires with tpms/ltpws sensors. Model all. No models years.
• 10192234Aug 27, 2013Equipment. Two methods are used to update/upgrade Navigation Map Data: 1. The customer goes to www.nissannavigation.com and is mailed update disc(s) or SD Card and installs data, OR 2. The dealership is mailed update disc(s) and the customer must visit the dealership to have data installed. Use the matrix in this bulletin to determine which method is utilized for each Applied Vehicle. See this bulletin for further detail.
• 10192233Aug 27, 2013Equipment, Wheels. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming…
• 10192231Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
• 10192217Jul 23, 2013Wheels, Steering, Brakes. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192216Jul 23, 2013Suspension, Steering, Brakes, Wheels. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192208Jul 5, 2013Brakes, Equipment, Back-over prevention (rear camera), Wheels. IF YOU CONFIRM: A creak type noise (like walking on a wood floor) coming from the rear brakes as the brake pedal is applied. - This noise is usually heard when applying the brake pedal at very low speeds i.e. parking lot speeds AND / OR - When applying the brake pedal while the vehicle is stopped. ACTION: Replace both rear wheel cylinders with those from the Parts Information table below.
• 10052624Jul 5, 2013Brakes. Nissan: on certain vehicles, there is a noise, creaking (like walking on wooden floor), coming from rear brake drums, when the brake pedal is applied. Model 2013 sentra.
• 10192202Jun 27, 2013Air bags, Electrical system, Transmission and drivetrain, Engine cooling. Nissan is conducting a voluntary service campaign to reprogram the Engine Control Module (ECM), and if necessary, the Transmission Control Module (TCM) on certain specific 2013 Nissan Sentra vehicles at no charge to the customer for parts or labor. The reprogramming will prevent a condition in which the vehicle's engine may stop running under certain unique conditions at cold start.
• 10051662Jun 27, 2013Transmission and drivetrain, Engine. Nissan: see document search button for owner letter. Voluntary service campaign 2013 sentra cold idle ecm and tcm reprogram. The reprogramming will prevent a condition which the vehicle's engine may stop running under certain unique conditions at cold starts. *js updated 9/30/13.
• 10192192Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10192178May 14, 2013Suspension. SERVICE INFORMATION If a customer would like to activate a subscription for any of the following services: - SiriusXM Satellite Radio, NavTraffic, NavWeather, Travel Link Weather OR If a radio is replaced for any reason, and a customer has an active subscription to any of the above services, OR If a customer claims to have an active subscription to any of the above services, AND any portion of the subscribed…
• 10192158Apr 4, 2013Electrical system. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
• 10051768Apr 4, 2013Vehicle speed control. Nissan: cruise control will not set and dtc p0605 is stored.
• 10192155Apr 3, 2013Vehicle speed control, Seat belts. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled…
• 10051767Apr 3, 2013Latches, locks and linkages. Nissan: lock/unlock request button on outside handle does not respond.
• 10192145Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192143Mar 15, 2013Transmission and drivetrain, Electrical system. Nissan is conducting a voluntary service campaign to reprogram the Engine Control Module (ECM), and if necessary, the Transmission Control Module (TCM) on certain specific 2013 Nissan Sentra vehicles.
• 10051855Feb 27, 2013Engine cooling. Engine has hesitation or stops running at idle or very low speeds. Nissan.
• 10049659Feb 27, 2013Engine. Nissan: 2013 sentra engine has hesitation or stops running at idle or very low speeds. The engine intermittently experiences a small rpm decrease for a short duration or stops running during braking, as the vehicle is coming to a stop. *js updated version on 4/12/2013.
• 10192127Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192125Feb 11, 2013Body and structure. Nissan has learned that due to an inadvertent error, the window sticker on your vehicle listed accessory items which were not actually installed on your vehicle.
• 10192100Dec 21, 2012Wheels. SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.
• 10192098Dec 20, 2012Transmission and drivetrain. Nissan is conducting a dealer service action to reprogram the ECM and if necessary TCM on specific 2013 Nissan Sentra vehicles to reprogram the ECM and TCM to prevent a decrease in engine RPM under certain cold state conditions which may cause hesitation.
• 10192087Dec 12, 2012Visibility (wipers, defrost, mirrors). SERVICE INFORMATION When replacing the wiper blades or refills, the wipers must be temporarily commanded to park half way through their sweep into their "Service Position" on the windshield. Please see this bulletin for further details.
• 10192067Nov 14, 2012Equipment. SERVICE INFORMATION The location of the Navigation (NAVI) SD Map Card has been changed for vehicles being shipped to dealers. - For the Applied Vehicles the NAVI SD Map Card is no longer in the Owners Manual Bag located in the trunk. - The Applied Vehicles now are shipped with the SD Map Card already inserted in the slot on the Face of the NAVI unit.
• 10192059Oct 29, 2012Equipment, Electrical system. SERVICE INFORMATION - The Extended Storage Switch (ESS) now includes the enable/disable of BCM transit mode. - Operating the ESS will, at the same time, enable/disable the BCM transit mode with one operation (as opposed to separately on other models). - Together, the ESS and BCM transit mode are now referred to as "Shipping Mode." - The ESS is still located in the fuse panel.
• 10046601Sep 25, 2012Brakes. Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. Model 2007-2013 nissan.

← All problems reported for the 2013 Nissan Sentra