2014 Subaru Forester Technical Service Bulletins

637 technical service bulletins (TSBs) are on record for the 2014 Subaru Forester. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10150887Oct 9, 2018Electrical system, Body and structure. This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just…
• 10146487Sep 27, 2018Steering. This Service Information bulletin provides helpful tips to simplify the diagnosis of sound concerns originating in the electronic power steering (EPS) gearbox (steering rack) assembly. If a vehicle presents with a ?rattling?, ?knocking? or possibly a ?clanging? type sound coming from the steering rack and / or a vibration felt through the steering wheel, use the flow chart below to help make diagnosis of the…
• 10146486Sep 27, 2018Equipment. A design change was made to the blower motor assembly to address the following customer concerns: ? Blower fan is either inoperative or only operates on high speed. ? Excessive rotational-type sound heard when the fan is operating.
• 10146480Sep 18, 2018Exterior lighting. This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
• 10145075Aug 28, 2018Equipment. The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes. We advise you to always refer to the STIS web site when looking for the latest Service information.
• 10145073Aug 24, 2018Body and structure, Suspension. This bulletin provides potential source locations and procedures to help isolate areas of the vehicle which may be generating popping, clicking or creaking sounds when the body is in a ?twisting? condition. This can occur while driving on rough, irregular or uneven road surfaces or even during lowspeed maneuvers such as pulling into or backing out of a driveway.
• 10145071Aug 22, 2018Seats. This Service Information Bulletin provides a revised troubleshooting procedure and tips to follow when diagnosing a DTC B1650- ?Occupant Classification System Malfunction?. This DTC may also be accompanied by B1760, B1761, B1771 or B1795 as found in the Occupant Detection control module. The new procedure is designed to help avoid unnecessary part (seat cushion assembly) replacements.
• 10144874Aug 1, 2018Equipment, Engine. In conjunction with the launch of our new Remanufactured FB Engine Short Block Program, SOA would like to reinforce Core Return Policy (See Parts Policy & Procedures Manual ? Section 12.3 Core Returns ? Reman) and provide suggestions for removal and handling of the short block.
• 10144873Aug 1, 2018Equipment, Engine. As part of our dedication to customer satisfaction, Subaru of America, Inc. is initiating a program to extend the original New Car Powertrain Limited Warranty coverage for excessive engine oilconsumption on applicable vehicles to 8 years / 100,000 miles from the original warranty start date.This Warranty Extension will not cover any excessive engine oil consumption found to be a result ofany condition(s) other than…
• 10143877Jul 30, 2018Electrical system. This Service Information bulletin announces the standardization of the IG2 and ACC relays used on the models listed. Both of these relays are located on the back (front facing) side of the passenger compartment fuse box (F/B).
• 10143878Jul 28, 2018Visibility (wipers, defrost, mirrors). This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
• 10143869Jul 24, 2018Steering. This bulletin announces availability of a new Electronic Power Steering (EPS) gear box assembly designed to address a VERY limited number of customer concerns regarding uneven steering effort felt when turning left or right. In areas where high concentrations of road salt are used to melt ice and snow, corrosion may develop and cause a portion of the gear box housing to crack if the vehicle were to suffer a large…
• 10143875Jul 18, 2018Engine cooling. TURBO MODELS ONLY. This bulletin announces availability of new parts to address a limited number of reports involving an engine vibration felt when at idle after the engine is up to operating temperature. In some cases, the above engine misfire DTCs may also result causing the Check Engine light to illuminate in error.
• 10142838Jun 21, 2018Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components.
• 10142825Jun 20, 2018Steering. This bulletin announces a design change made to the forward bushing used in the front lower control arm to address customer concerns of a rattle-type sound and / or a possible vibration felt in the steering wheel. The material for the cushion portion of the front bushing has been changed.
• 10142826Jun 11, 2018Electrical system. This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed to set and result in the related system?s warning lamp to illuminate.
• 10141490May 31, 2018Brakes. This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed. The new shims incorporate a new laminated design with increased damping characteristics to eliminate vibration identified as the root cause of the sound. The new kits include shims only (NO brake pads).
• 10141491May 22, 2018Equipment, Electrical system, Seats. This Service Information Bulletin provides a revised troubleshooting procedure and tips to follow when diagnosing a DTC B1650-?Occupant Classification System Malfunction?. This DTC may also be accompanied by B1760, B1761, B1771 or B1795 as found in the Occupant Detection control module. The new procedure is designed to help avoid unnecessary part (seat cushion assembly) replacements.
• 10141499May 10, 2018Equipment. This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
• 10133522Mar 28, 2018Visibility (wipers, defrost, mirrors). This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets
• 10133521Mar 28, 2018Electrical system. On Forester Turbo and applicable WRX models, after re-connecting the battery, if the ignition switch is turned back ?ON? within one minute after the first time the ignition is turned ?OFF?, it becomes possible for the CEL to illuminate storing DTC P0606 in memory. The code will not occur immediately, but may occur after a period of time depending upon how the vehicle is operated
• 10133528Mar 23, 2018Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components
• 10133527Mar 13, 2018Transmission and drivetrain. 2010-15 Legacy/ Outback 2.5L NA CVT, 2015 Legacy/ Outback 3.6L NA CVT, 2012-15 Impreza 2.0L NA CVT, 2013-15 Crosstrek 2.0L NA CVT, 2014-15 Crosstrek Hybrid CVT 2014-15 Forester 2.5L NA CVT 2014-15 Forester 2.0L Turbo CVT 2015 WRX 2.0L Turbo models only. In the interest of customer satisfaction, Subaru of America, Inc.
• 10133517Mar 12, 2018Electrical system. This bulletin announces availability of new VDC Control Module & Hydraulic Units (VDCCM&H/U) to address isolated customer concerns of the green Hill Holder light blinking and cancel warning alarm sounding during cranking / starting the engine
• 10133516Mar 6, 2018Engine, Transmission and drivetrain. 2013-14MY Legacy and Outback Models with 2.5L FB Engines, 2011-14MY Forester Models with 2.5L FB Engines, 2015 MY Forester (Manual Transmissions Only), with 2.5L FB Engines, 2012-13 MY Impreza and XV Crosstrek Models with 2.0 FB Engines, 2014-15 MY Impreza and XV Crosstrek Models (Manual Transmissions Only) with 2.0 FB Engine As part of our dedication to customer satisfaction, Subaru of America, Inc.
• 10133529Mar 2, 2018Equipment. The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
• 10140470Feb 13, 2018Equipment, Body and structure. This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to…
• 10140483Feb 9, 2018Engine. 2.0L Turbor Models only. This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333.
• 10140468Feb 9, 2018Engine, Electrical system. 2.0L Turbor Models only. This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333.
• 10140480Feb 6, 2018Engine cooling, Equipment. 2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrence of ice formation from condensation in the duct?s PCV system passages.
• 10140425Feb 6, 2018Engine cooling. 2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrences of ice formation from condensation in the duct?s PCV system passages.
• 10130270Jan 24, 2018Brakes, Exterior lighting. This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
• 10130272Jan 22, 2018Body and structure. This bulletin describes a design change to the center bracket component of the window regulator assembly. The change was made to address customer concerns of the front door glass shuddering while opening or closing. Moisture accumulation in the run channels can cause a stick-slip / vibration condition as the glass goes up and down resulting in the shudder.
• 10130277Jan 11, 2018Body and structure. ( 2017-2018MY Impreza - 5 Dr Only)
• 10138778Dec 15, 2017Air bags, Electrical system, Equipment. NOTE: The Airbag systems used on previous and current WRX, STI and Tribeca models are NOT equipped with EDR functionality. This Bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system. The function of the EDR is best explained using the following statements found in the vehicle Owner?s Manual: ?This vehicle is equipped with an event data…
• 10138780Dec 7, 2017Equipment, Air bags. This Service Information Bulletin provides a revised troubleshooting procedure and tips to follow when diagnosing a DTC B1650- ?Occupant Classification System Malfunction?. This DTC may also be accompanied by B1760, B1761, B1771 or B1795 as found in the Occupant Detection control module. The new procedure is designed to help avoid unnecessary part (seat cushion assembly) replacements.
• 10125885Nov 9, 2017Equipment, Transmission and drivetrain. CVT MODELS ONLY. In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first).
• 10131667Oct 12, 2017Seats. This Service Information bulletin provides a procedure for diagnosis of Occupant Detection System (ODS) DTC B1760- Sensor Mat Abnormal and/or B1650- Occupant Classification System Malfunction. This information replaces the current procedure until the Service Manual is updated in the near future. DTC B1760 and/or B1650 may set if liquid inadvertently spilled onto the seat cushion (or rain water entering from a…
• 10131628Sep 22, 2017Exterior lighting. EXCLUDES HYBRID MODELS. This bulletin announces a design change to the brake light switch (BLS) to reduce the possibility of improper illumination of the ABS and/or VDC warning lamp. In the event a product containing silicone is used to lubricate the BLS or for other purposes in the area around the switch, a non-conductive coating may develop over time on the internal electrical contacts and affect operation of the…
• 10131632Sep 11, 2017Engine cooling. This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
• 10131633Sep 6, 2017Equipment. Models with Manual HVAC Systems only. This Service Information bulletin provides precautions to use when removing the HVAC control panel to prevent damaging the blower fan speed switch. When removing the control panel, if the fan speed switch wiring harness is pulled taught or becomes stressed, the switch may be damaged. If the connector (lower) portion of the switch becomes separated from the switch body even…
• 10117553Aug 16, 2017Equipment. This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Service Policies and Procedures Manual found in subarunet.
• 10117558Aug 14, 2017Electrical system, Transmission and drivetrain. 2.0L DIT Models Only. Subaru of America, Inc. has determined that vehicles affected by this Service Program require ECM reprogramming. This bulletin includes the service procedure for diagnosis and repair of customer concerns involving engine idle roughness or, in some cases, engine noise and/or damage resulting from spark knock (pre-ignition). The Engine Control Module logic has also been optimized requiring the…
• 10117541Aug 8, 2017Electrical system. 2.5L MODELS ONLY. This bulletin provides a procedure for diagnosis and repair of DTC P0300 which may result from fluctuation of the alternator's current output outside of the specified limits.
• 10117531Jun 26, 2017Air bags. This Service Information bulletin provides a procedure for diagnosis of Occupant Detection System (ODS) DTC B1760- Sensor Mat Abnormal and/or B1650- Occupant Classification System Malfunction. This information replaces the current procedure until the Service Manual is updated in the near future. DTC B1760 and/or B1650 may set if liquid inadvertently spilled onto the seat cushion (or rain water entering from a…
• 10117528Jun 26, 2017Engine cooling. This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the…
• 10117538Jun 21, 2017Equipment, Transmission and drivetrain. CVT MODELS ONLY. In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first).
• 10117534Jun 15, 2017Electrical system, Equipment. This bulletin announces availability of ECM reprogramming files designed to optimize the ECM for improving HVAC blower fan speed control. There have been a limited number of cases with reports describing the blower fan speed fluctuating / changing without input from the customer when the blower is set to maximum speed.
• 10117529Jun 15, 2017Engine, Engine cooling. This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
• 10117530Jun 6, 2017Exterior lighting. This bulletin announces a design change to the brake light switch (BLS) to reduce the possibility of improper illumination of the ABS and/or VDC warning lamp. In the event a product containing silicone is used to lubricate the BLS or for other purposes in the area around the switch, a non-conductive coating may develop over time on the internal electrical contacts and affect operation of the switch.

← All problems reported for the 2014 Subaru Forester