2011 Audi A4 Avant Technical Service Bulletins

626 technical service bulletins (TSBs) are on record for the 2011 Audi A4 Avant. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10123586Jun 7, 2013Engine cooling. Supersedes Technical Service Bulletin Group 21 number 13-13 dated April 4, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure…
• 10123562Jun 4, 2013Electrical system. Supersedes Technical Service Bulletin Group 85 number 13-15 dated March 29, 2013. The trim panel at the defroster vent on the instrument panel is deformed. The trim panel is composed of a material which expands in a moist condition. The instrument panel restricts this expansion which leads to deformation of the trim.
• 10124944May 29, 2013Equipment. Supersedes Technical Service Bulletin Group 01 number 13-83 dated March 29, 2013. MIL on. DTCs are stored in the engine control module. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
• 10052307May 29, 2013Vehicle speed control. Audi: some vehicles may lack power or will not move after stop due to simultaneously depressing the brake and accelerator pedals.
• 10052343May 23, 2013Exterior lighting. Audi: the vehicle lights malfunction message may be displayed on the dashboard cluster. There is no failure. Also included model a4 my 2014, model a5 cabriolet my 2014, model q5 my 2014, model s7 my 2012-2014, model rs7 my 2014.
• 10124941May 14, 2013Engine. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10124955May 13, 2013Electrical system. Faults are stored in the engine control module (ECM). Engine shakes. Some of the Bosch ignition coils installed in the affected vehicles may fail prematurely.
• 10052288May 13, 2013Electrical system. Audi: some vehicles may have a defect with the bosch ignition coils. The may prematurely fail.
• 10066961May 9, 2013Body and structure. Summary to be provided on a future date.
• 10066830May 7, 2013Steering. Summary to be provided on a future date.
• 10123915Apr 26, 2013Transmission and drivetrain, Electrical system. Supersedes Technical Service Bulletin Group 37 number 13-99 dated April 1, 2013. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module (TCM), J217 (02). If DFCCs do not match exactly, this TSB does not apply. The DTCs…
• 10123914Apr 24, 2013Electrical system, Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 13-97 dated March 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module (TCM), J217 (address word 03). The fault occurs with ATF temperature below 60o…
• 10123929Apr 19, 2013Equipment. The fresh air blower is inoperative. DTCs may be stored in the heating and air conditioning electronics control module (address word 08). Malfunctions of the fresh air blower could be caused by a faulty printed circuit board in the fresh air blower control module and the carbon brushes bind in the brush holder and, as a consequence, lose contact with the motor commutator of the fresh air blower.
• 10123911Apr 19, 2013Equipment. Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote…
• 10123905Apr 15, 2013Engine cooling. Customer may report coolant leaking from the engine area. The leak can be traced to the connection of the water pump and the hose leading to the heater core. The seal ring is not the cause of the leak.
• 10123904Apr 15, 2013Equipment, Engine. MIL on. Rough idle. DTCs are stored in the Engine Control Module (ECM), J623 (address word 01). Engine may have reduced performance without significant loss of power or stalling. Because there are a number of different misfire faults (unrelated to ignition coil operation) that could cause the MIL to illuminate, proper Guided Fault Finding (GFF) misfire diagnosis must be followed before any ignition coils are…
• 10123913Apr 9, 2013Transmission and drivetrain, Electrical system. Supersedes Technical Service Bulletin Group 37 number 13-83 dated January 31, 2013. Hesitation concerns, harsh downshifts when braking, or harsh 1-2 upshifts. Further transmission control module (TCM), J217, software calibration needed to improve shift concerns. Further engine control module (ECM), J623, software calibration needed to improve hesitation.
• 10066835Apr 9, 2013Brakes. Summary to be provided on a future date.
• 10051750Apr 9, 2013Electrical system, Transmission and drivetrain. Audi: when braking, would have harsh downshifts and hesitation concerns and also upshifts 1-2 are harsh. Calibration of software to improve shift concerns and hesitation. Models 2011-12 a4, a4 avant, a5, a5 cabriolet, q5. *pe updated 7/1/13.
• 10123907Apr 4, 2013Engine cooling. Supersedes Technical Service Bulletin Group 21 number 13-12 dated April 1, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure…
• 10123919Apr 1, 2013Transmission and drivetrain, Electrical system. Supersedes Technical Service Bulletin Group 37 number 12-77 dated December 19, 2012. Customer may report transmission warning light is illuminated. In some cases, the vehicle will not move after being started and placed into gear. After key cycle, the vehicle drives without restriction. DTCs are stored in the transmission control module, J217 (02). If DFCCs do not match exactly, this TSB does not apply.
• 10123906Apr 1, 2013Engine cooling. Supersedes Technical Service Bulletin Group 21 number 13-11 dated March 6, 2013. MIL on, DTC P0299 (Negative Pressure Deviation) is stored. Turbocharger waste gate flap has play. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P0299 (Negative Pressure…
• 10123901Apr 1, 2013Equipment. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center
• 10123886Mar 29, 2013Engine cooling. MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction.
• 10123858Mar 29, 2013Equipment. The trim panel at the defroster vent on the instrument panel is deformed. The trim panel is composed of a material which expands in a moist condition. The instrument panel restricts this expansion which leads to deformation of the trim.
• 10123849Mar 29, 2013Exterior lighting. Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision.
• 10123883Mar 28, 2013Engine cooling. Supersedes Technical Service Bulletin Group 17 number 13-37 dated March 13, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine.
• 10123854Mar 28, 2013Equipment. Supersedes Technical Service Bulletin Group 91 number 13-73 dated January 25, 2013. Customer complains of a "popping" noise from the radio followed by 10-15 seconds of no audio. The concern can happen in any audio source. Vehicle is equipped with MMI 3G or MMI 3G+ infotainment systems. Vehicle is not equipped with Bose or Bang & Olufsen sound systems.
• 10123884Mar 27, 2013Engine. Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement.
• 10123861Mar 27, 2013Body and structure, Latches, locks and linkages. Supersedes Technical Service Bulletin Group 57 number 12-80 dated November 9, 2012. The door cannot be opened from outside with the outer door handle, but it can be opened with the inner handle. The complaint is often described as follows: The customer locks the vehicle and checks by pulling the door handle whether the vehicle is locked. When opening the vehicle again, the door cannot be opened. It feels as if the…
• 10123846Mar 27, 2013Steering. Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering…
• 10066960Mar 27, 2013Body and structure. Summary to be provided on a future date.
• 10123882Mar 25, 2013Engine cooling. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10123862Mar 20, 2013Latches, locks and linkages, Body and structure. Supersedes Technical Service Bulletin Group 57 number 12-73 dated September 24, 2012. The exterior door handle touch sensors (Advanced key) are inoperative on one or several doors. The key blade can be used mechanically (driver door or trunk) or remote electrically (key remote buttons) to unlock and lock the vehicle.
• 10066872Mar 18, 2013Transmission and drivetrain. Summary to be provided on a future date.
• 10123885Mar 13, 2013Engine cooling. Supersedes Technical Service Bulletin Group 17 number 13-36 dated February 14, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine.
• 10123896Mar 7, 2013Engine cooling. The engine warning light is on after engine replacement. The engine is not running roughly. However, the engine control module, J623 (01), is storing one or more of the following engine misfire fault codes: DTCs P0300 - P0304. The fault codes occur at light load, between 8% and 14% accelerator pedal position. The programmed values for the misfiring recognition are not automatically reset by deleting the memory once.
• 10123878Mar 4, 2013Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 13-86 dated February 6, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 (Torque Converter Clutch Circuit Performance) or "Stuck Off" is stored in transmission control module, J217 (03). The fault occurs with ATF temperature below 60o C.
• 10123863Mar 4, 2013Latches, locks and linkages, Electrical system. Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced.
• 10123996Feb 22, 2013Latches, locks and linkages, Equipment. Supersedes Technical Service Bulletin Group 57 number 11-48 dated July 25, 2011. Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button.
• 10123987Feb 18, 2013Suspension. Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control.
• 10124007Feb 14, 2013Exterior lighting, Electrical system. Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly.
• 10123993Feb 14, 2013Engine cooling. Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch.
• 10123973Feb 14, 2013Transmission and drivetrain. Supersedes Technical Service Bulletin Group 34 number 13-14 dated January 30, 2013. The transmission jumps out of 6th gear. Improved 5th and 6th shift fork and gearshift unit.
• 10123971Feb 14, 2013Engine cooling. Supersedes Technical Service Bulletin Group 17 number 12-34 dated December 12, 2012. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine.
• 10063863Feb 14, 2013Transmission and drivetrain. Summary to be provided on a future date.
• 10063849Feb 14, 2013Engine. Summary to be provided on a future date.
• 10123975Feb 6, 2013Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 13-85 dated February 4, 2013. Customer may report transmission warning lamp illuminated in instrument cluster. After ignition cycle, the warning message is no longer present. DTC P074100 "Torque Converter Clutch Circuit Performance" or "Stuck Off" is stored in TCM. The fault occurs with ATF temperature below 60o C. Check for this temp range in the extended…
• 10124000Feb 5, 2013Back-over prevention (rear camera). Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions.
• 10123995Feb 5, 2013Latches, locks and linkages, Equipment. Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced.

← All problems reported for the 2011 Audi A4 Avant