2010 Audi A5 Technical Service Bulletins

892 technical service bulletins (TSBs) are on record for the 2010 Audi A5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10122523Jul 30, 2014Electrical system. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM.
• 10066402Jul 30, 2014Equipment. Summary to be provided on a future date.
• 10231144Jul 28, 2014Equipment. Technical bulletins and updates
• 10231126Jul 28, 2014Electrical system. i-wire new wiring diagram application
• 10122571Jul 24, 2014Equipment. Supersedes Technical Service Bulletin Group 96 number 13-61 dated May 28, 2013. The sunglass holder in the dome light assembly will not latch closed. The sunglass holder spring latch mechanism may have been damaged during the assembly procedure.
• 10122555Jul 18, 2014Electrical system. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393).
• 10216620Jul 17, 2014Back-over prevention (rear camera), Brakes. Assistance to properly diagnose a fuel pressure sensor -G247- concern.
• 10122526Jul 17, 2014Fuel system. Supersedes Technical Service Bulletin Group 01 number 11-32 dated October 26, 2011. The MIL is on. DTCs may be stored in the ECM. Assistance to properly diagnose a fuel pressure sensor -G247- concern.
• 10228297Jul 15, 2014Electrical system. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10224976Jul 15, 2014Back-over prevention (rear camera). This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10221949Jul 15, 2014Equipment. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10122522Jul 15, 2014Electrical system. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update.
• 10250966Jul 14, 2014Brakes. Brake pulsation diagnostic guidelines
• 10231125Jul 14, 2014Equipment. Pending service solutions and bulletins
• 10128242Jul 14, 2014Suspension, Brakes, Air bags. Brake-related vibration and pulsation has several causes that depend on driving style and resulting brake disc temperature, as well as environmental conditions. Both the intensity of the wear of the brake system and the type of wear depend on the operating conditions of the vehicle. The wear of the brake discs is determined by the frequency and intensity of the brake operations.
• 10250964Jul 10, 2014Steering. Steering feels stiff when turning
• 10249054Jul 10, 2014Other or unknown. Due to new Minnesota state regulations regarding biofuels, biodiesel blends of B5 or less may not be available in the State of Minnesota.
• 10122563Jul 10, 2014Equipment. Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises.
• 10122553Jul 10, 2014Steering. Supersedes Technical Service Bulletin Group 48 number 13-56 dated December 13, 2013. The customer states that the steering feels stiff during turning. The condition occurs when the vehicle is stationary. The steering shaft needs to be updated.
• 10056396Jul 10, 2014Steering. Audi: when turning, the steering feels stiff and occurs even when vehicle is stationary. Intermediate steering shaft needs to be improved. Model 2008-2014 a4, a5, q5.
• 10250960Jul 8, 2014Suspension. Rattling or knocking noise from front end when driving over bumps
• 10250666Jul 8, 2014Back-over prevention (rear camera). Rattling or knocking noise from front end when driving over bumps
• 10122541Jul 8, 2014Brakes. Supersedes Technical Service Bulletin Group 40 number 14-39 dated February 13, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This…
• 10066024Jul 8, 2014Brakes. Summary to be provided on a future date.
• 10231124Jul 7, 2014Equipment. Technical bulletins and updates
• 10250959Jul 2, 2014Suspension. Shock absorber leaks: assessment aid
• 10250958Jul 2, 2014Steering. Squeaking noises when steering or maneuvering
• 10250665Jul 2, 2014Body and structure, Equipment. Shock absorber leaks: assessment aid
• 10250664Jul 2, 2014Steering. Squeaking noises when steering or maneuvering
• 10122540Jul 2, 2014Suspension. Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers.
• 10122539Jul 2, 2014Steering. Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the…
• 10231130Jun 30, 2014Engine cooling. Idenifying and mixing factory fill engine coolants
• 10250981Jun 26, 2014Tires. Message "TPMS" in instrument cluster
• 10122419Jun 26, 2014Equipment, Tires. Supersedes Technical Service Bulletin Group 44 number 13-38 dated July 11, 2013. Scenario A is after the engine is started, the message "TPMS" appears briefly then turns off. No DTCs are stored. Scenario B is the message "TPMS" appears constantly. DTC 03159 (tire pressure monitoring in ESP function) is stored in the ABS control module, J104 (address word 03), with one or more additional DTCs.
• 10066032Jun 26, 2014Electrical system. Summary to be provided on a future date.
• 10122415Jun 20, 2014Engine cooling. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service.
• 10231127Jun 9, 2014Equipment, Electrical system. ElsaPro Software update and technical bulletins
• 10216703Jun 6, 2014Equipment, Engine cooling. Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose flap, which sets DTC P029900 (Negative Pressure Deviation).
• 10122417Jun 6, 2014Engine cooling. Supersedes Technical Service Bulletin Group 21 number 13-16 dated July 9, 2013. The MIL is on. DTC P029900 (Negative Pressure Deviation) is stored as a static fault in the engine control module (ECM), J623 (address word 01). Under certain driving conditions, the linkage for the waste gate actuation can encounter excessive wear which leads to play at the waste gate flap. This leads to boost escaping through a loose…
• 10226530Jun 3, 2014Transmission and drivetrain. ATF pan leaks
• 10210680Jun 3, 2014Transmission and drivetrain, Engine cooling. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak. Automatic transmission fluid is leaking at the sump pan gasket.
• 10122440Jun 3, 2014Electrical system. Audi has determined that, under specific conditions, the turbocharger could malfunction and may cause the Malfunction Indicator Lamp (MIL) on the instrument cluster to illuminate due to the presence of specific fault codes caused by this component. The MIL is part of your on-board diagnostic system. Please refer to your owner's manual for additional information about the MIL.
• 10122418Jun 3, 2014Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 11-19 dated January 31, 2011. Automatic transmission fluid is leaking at the sump pan gasket. As the sump pan gasket settles, the torque of the bolts decreases and the seal may leak.
• 10212703May 29, 2014Transmission and drivetrain. Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
• 10228295May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10226529May 28, 2014Transmission and drivetrain. Vehicle lacks power or will not move after stop due to simultaneous depressing of the brake and accelerator pedals
• 10224974May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10221947May 28, 2014Engine cooling. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage.
• 10210679May 28, 2014Electronic stability control, Transmission and drivetrain. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. With the introduction of Electronic Power Control (EPC) (no accelerator cable) to fuel injection systems, an engine RPM control feature has been incorporated into the engine electronic control system…
• 10122465May 28, 2014Transmission and drivetrain. Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left…

← All problems reported for the 2010 Audi A5