2013 BMW 320I Technical Service Bulletins

530 technical service bulletins (TSBs) are on record for the 2013 BMW 320I. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10147829Nov 1, 2015Electrical system. """Efficient Dynamics"" in the Instrument Cluster Partially Displayed During CC Message. After switching from terminal 15 to terminal R, the ""Efficient Dynamics"" wording in the instrument cluster, below the tachometer, is partially displayed while a CCM (Check Control Message) is shown. Only the word ""Efficient"" is displayed. Software error in the instrument cluster multi-information display"
• 10147784Oct 1, 2015Equipment, Electrical system. "Active Sound Design ASD inoperative after programming. After programming with ISTA/P V3.56.1 Active Sound Design (ASD) no longer provides simulated engine sounds A fault is stored in the ASD module. Fault Code 8053A5 ""ASD; invalid coding data for equalizing"" Invalid ASD coding data"
• 10147783Oct 1, 2015Equipment, Electrical system. Navigation CIC vehicle positioning temporarily incorrect. The Navigation system may temporarily display the vehicle in the wrong location. This mainly occurs on short sections of road and the vehicle position may take 2 or more minutes to be shown correctly. Invalid calculation in the CIC head unit.
• 10147769Oct 1, 2015Transmission and drivetrain. "Grinding or cracking noise when putting vehicle in gear/ ""Drive Disturbed"" displayed. A metallic grinding or cracking noise is heard from the rear of the vehicle when selecting Drive or Reverse. There may also be a Check Control message ""Drive Disturbed"" displayed. CAUSE The inner and/or outer universal joint on the right and/or left rear output shaft has failed."
• 10147760Oct 1, 2015Engine cooling. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
• 10147264Sep 1, 2015Equipment. IHKA - Outlet Temperature is Different on Both Sides. The IHKA settings on the left- and right-hand side are identical. The outlet temperature for both sides is different. Software application error in IHKA.
• 10147263Sep 1, 2015Equipment. "IHKA - Blower Runs in Emergency Mode. After the ignition is turned off and the vehicle is locked, the heating and air conditioning blower motor runs continuously. The next time the vehicle is started there may be the CCM (Check control message) displayed for ""Increased battery discharge"". CAUSE The blower output stage receives an invalid LIN bus signal during operation and switches to emergency mode.
• 10147262Sep 1, 2015Equipment. IHKA - Recirculation Function Changes from Manual to Automatic. While driving, the air recirculation button on IHKA changes by itself from manual to automatic or automatic to manual mode. CAUSE The IHKA operating software is too sensitive.
• 10147259Sep 1, 2015Exterior lighting. "Reverse Light is Intermittently Inoperative. CCM (Check control message) is displayed indicating a ""reverse light"" is out. CAUSE There is a weak spring in bulb socket or bulb carrier (on the luggage compartment lid) which is causing a bad contact with the bulb."
• 10147251Sep 1, 2015Body and structure. Driver or Passenger's Front Doors Handles Inoperable. Sporadically it is not possible to open the driver or passenger's front door from the outside or inside door handle. Multiple attempts will eventually open the door. Comfort access operation of the outside door handle works properly. This situation occurs at temperatures below 37 °F. CAUSE Incorrect routing of the Bowden cable.
• 10147243Sep 1, 2015Tires. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147241Sep 1, 2015Wheels, Transmission and drivetrain. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
• 10147235Sep 1, 2015Engine cooling, Engine. ?N20 and N26 engine: Smoke from Exhaust when Starting a Cold Engine. When starting a cold engine, blue smoke can be seen emitting from the exhaust tailpipe for approximately 10-20 seconds. No turbo charger boost faults are stored and no drivability issues can be detected. Engine oil leakage into the induction system and/or the turbo charger assembly.
• 10151415Aug 1, 2015Electrical system, Equipment. "Instrument Cluster: CBS ""Running-in Check"" is Displayed. After replacing and / or programming the instrument cluster with ISTA/P 3.55.0 or higher (integration Level F020-15-03-501 or higher), the CBS (Condition Based Service) displays ""running-in check"" or ""1200 mile service is due"". The parameters of the CBS scopes for oil service, brake fluid, etc, can also be implausible or invalid.
• 10151404Aug 1, 2015Transmission and drivetrain. Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle…
• 10151399Aug 1, 2015Engine. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
• 10147211Jul 1, 2015Equipment. NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick…
• 10147202Jul 1, 2015Equipment. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the…
• 10147200Jul 1, 2015Transmission and drivetrain, Wheels, Brakes. Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
• 10147197Jul 1, 2015Steering, Brakes. Power-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues.
• 10147189Jul 1, 2015Electrical system, Fuel system. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ?
• 10146945Jul 1, 2015Equipment, Engine cooling. The plastic oil filter housing may fail and lead to an internal and/or external engine oil or coolant leak.
• 10146944Jul 1, 2015Engine. N20 Engine: Repeated Juddering or Surging While Accelerating. The vehicle judders or surges repeatedly while accelerating in hot ambient temperatures between 3,000 RPM and 5,000 RPM. The Service Engine Soon lamp is not illuminated, and no fault codes are stored in the vehicle memory related to this complaint. CAUSE The EPDW (electropneumatic pressure convertor) for the turbocharger wastegate valve is binding…
• 10146942Jul 1, 2015Electrical system, Exterior lighting. Front Parking Lights Inoperative. After programming the vehicle with ISTA/P 3.56.1, both front parking lights (integrated in the headlights) have been deactivated and no Check Control message is displayed. CAUSE FEM software error in ISTA/P 3.56.1
• 10147721Jun 1, 2015Electrical system. "Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: ? ""8044A3 - Wiring, horn short circuit to earth"" ? ""8044A4 - Wiring, horn short circuit to positive"" ? ""8044A5 - Wiring, horn relay is defective or short circuit to positive"" Water has entered the horn and caused it to fail internally (shorted out)."
• 10147714Jun 1, 2015Transmission and drivetrain. 8HP: Transmission Fluid Loss from Cooler Lines Connections. There is a transmission fluid leak in the area around the oil cooler lines (on the transmission side). CAUSE Damaged o-rings due to unfavorable cooling line connection tolerances
• 10147711Jun 1, 2015Engine, Fuel system. N20 Engine: Ticking Noise from High-pressure Fuel Pump. The customer complains of a high-frequency ticking noise from the engine compartment. The noise can be heard inside and outside the vehicle. Mechanical vibrations inside the high-pressure fuel pump
• 10147154May 1, 2015Equipment. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147153May 1, 2015Equipment. A/C Cooling: Intermittent Reduction of Air Flow. The customer may complain of reduced air flow when the air conditioning system is operated for an extended time, usually longer than one hour. The complaint can vary due to one or more of the following variables: ? High outside ambient temperature ? Too much humidity ?
• 10147143May 1, 2015Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID…
• 10147141May 1, 2015Body and structure, Equipment. Removal Process: B-Pillar High Gloss Trim Protective Wrap. INFORMATION ONLY The key for successful wrap removal is to have the body cool (below 60 degrees) and dry. The recommendations are as follows: ? Before removing the B-pillar wrap, make sure the car body is dry and cool. ? Removing the wrap in the early morning hours will provide the best results. ?
• 10147136May 1, 2015Tires, Wheels. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc.
• 10147134May 1, 2015Electrical system, Transmission and drivetrain. Rattling Noise from Transmission Tunnel. A rattling or knocking noise is heard in the area of the gear selector switch (GWS) during engine load reversal. CAUSE The vent tube for the transfer case is making contact with the transmission tunnel.
• 10147130May 1, 2015Electrical system. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show…
• 10193495Apr 6, 2015Visibility (wipers, defrost, mirrors). The customer complains of rattling noises from the rear window when driving on rough roads.
• 10152317Apr 1, 2015Back-over prevention (rear camera). Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear…
• 10152306Apr 1, 2015Fuel system. "N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump.
• 10152305Apr 1, 2015Electrical system. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ?
• 10152302Apr 1, 2015Transmission and drivetrain. N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: ? 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the wiring.
• 10147690Mar 1, 2015Equipment. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us…
• 10147689Mar 1, 2015Vehicle speed control. "Remote Control Not Detected and/or Engine Will Not Start. One or more of the following situations can occur: 1. The remote control is not detected and the check control message (CCM) ""No remote control. Unable to start"" or ""Hold the remote control on the steering column"" is displayed. ? Fault code ""D90D1E - LIN bus error FBD receiver 1"" is stored. 2. The engine does not start with the CCM with ""Battery in…
• 10147686Mar 1, 2015Exterior lighting. "Halogen Headlight Side Bulbs Fail. The check control message (CCM) ""Parking lamp malfunction: Consult service center"" is displayed when the vehicle is started. Defective side light bulb on one or both sides"
• 10147678Mar 1, 2015Body and structure. Body Equipment March 2015 Technical Service. This Service Information bulletin supersedes SI B51 11 12 dated March 2012. designates changes to this revision SUBJECT Engine Hood Does Not Open Properly. The engine hood cannot be opened or it is only unlocking on one side. Note: The hood can be opened if the hood release lever is activated by one person while another person pulls upward on the hood at the same time…
• 10147676Mar 1, 2015Equipment. "Front Floor Mats Do Not Stay in Place. The Velcro patch attached to the bottom of the floor mat peels off. Poor adhesion of the Velcro patch Thank you for all the PuMA ""Info Only"" cases. From these cases, it has been determined that the Velcro peeling fault occurs on mats produced prior to May 2014. We no longer need ""Info Only"" cases from this time period."
• 10147667Mar 1, 2015Engine cooling, Engine. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission…
• 10147653Mar 1, 2015Engine. "N20 and N55 Engine: Engine Oil Filter Application for Plastic Oil Filter Housing. The current version of EPC does not provide all available options for the engine oil filters used in the N20 and N55 engines produced with a ""plastic"" oil filter housing. The illustration below will help identify the proper engine oil filter application until the EPC is corrected."
• 10147652Mar 1, 2015Engine. N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
• 10147091Feb 1, 2015Air bags. "Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger…
• 10147089Feb 1, 2015Visibility (wipers, defrost, mirrors). SI B64 04 12February 2015 Heating and Air ConditioningTechnical Service This Service Information bulletin supersedes SI B64 04 12 dated September 2013. designates changes to this revision SUBJECT Blower Makes an Unusual Noise. An unusual howling/vibrating noise can be heard from the glove compartment and passenger foot well area (blower motor).
• 10147084Feb 1, 2015Transmission and drivetrain, Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside…

← All problems reported for the 2013 BMW 320I