2015 BMW 320I Technical Service Bulletins

421 technical service bulletins (TSBs) are on record for the 2015 BMW 320I. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10147623Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts…
• 10147622Jan 1, 2015Brakes, Exterior lighting. "SUBJECT Check Control Message: Parking Light Failed. z A CCM (Check Control Message) displays ""Parking Light failed."" z All lights are functioning correctly. Software error in the TMS (Driver Module for Headlight)"
• 10147613Jan 1, 2015Brakes, Wheels. "SUBJECT Ticking Noise from Front Axle When Cornering. Covered under the terms of the BMW New Vehicle/SAV Limited Warranty. Defect Code:34 11 00 57 00Labor Operation:Labor Allowance:Description:34 11 220Refer to KSDRemoving and installing both front brake discsAnd:34 99 0002 FRUWork time for sanding hub surface of brake discs and cleaning wheel hub surfacesLabor operation code 34 11 220 is a Main labor operation.
• 10147602Jan 1, 2015Engine, Fuel system. SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL)…
• 10147601Jan 1, 2015Engine, Electrical system. This Service Information bulletin supersedes SI B12 35 14 dated December 2014. designates changes to this revision SUBJECT N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: z 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is…
• 10147599Jan 1, 2015Vehicle speed control. "SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon.
• 10147595Jan 1, 2015Engine, Electrical system. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles.
• 10147594Jan 1, 2015Transmission and drivetrain. SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the…
• 10147591Jan 1, 2015Engine cooling. SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement…
• 10148195Dec 1, 2014Equipment, Electrical system. Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service…
• 10148194Dec 1, 2014Equipment, Electrical system. iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z…
• 10148193Dec 1, 2014Electrical system, Equipment. Central Information Display Intermittently Flashes Off/On. Intermittently, the Central Information Display (CID) flashes off/on. Voltage supply error from the Headunit-high (HU-H) to the Central Information Display (CID) when the display brightness is set to 60% or higher.
• 10148192Dec 1, 2014Equipment, Electrical system. Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without…
• 10148186Dec 1, 2014Equipment, Electrical system. The Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
• 10148173Dec 1, 2014Fuel system. NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak. The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: z FC 190302 Fuel tank ventilation and purge air system micro leak leakage greater than 0_5 mm CAUSE Contamination of the NVLD pressure switch electrical contacts
• 10148170Dec 1, 2014Engine. N20, N26 Service Engine Soon Light On: Fault Code 1B9702 is Stored. The Service Engine Soon light (MIL) is on with only the following fault stored in the DME: ? 1B9702: Engine switch-off time, timer, instrument panel timer DME, Comparison: Value of instrument panel timer too low while engine is running This fault will not cause any engine running or drivability problems. Unfavorable instrument cluster and DME…
• 10148168Dec 1, 2014Transmission and drivetrain, Engine cooling. Fault Code 1D2008 Stored in DME. The Service Engine Soon light is on. Fault Code 1D2008: Map thermostat: jammed open is stored in the DME. There may also be a complaint of low heat output with lower outside temperatures. CAUSE During the engine warm-up, the engine coolant does not reach operating temperature within the DME's allowable time limits. This is caused by either a faulty thermostat inside the transmission…
• 10148429Nov 1, 2014Latches, locks and linkages, Electrical system. Unlocking Trunk with Remote Unlocks All Doors. After programming the vehicle with ISTA/P 2.47.1, unlocking the trunk with the remote changes to unlocking all the doors. An application error occurred after programming the vehicle to the Personal Profile Setting (PIA) in the Front Electronic Module (FEM).
• 10148423Nov 1, 2014Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10148420Nov 1, 2014Exterior lighting. Headlight Cleaning System: Functional Operation Change. The customer complains that the headlight cleaning system is not working properly and only works after several actuating attempts. CAUSE The "functional" operation of the headlight cleaning system was changed with integration level F020-14-07-500. The functional changes to the headlight cleaning system's operation will occur only after programming the vehicle…
• 10149382Oct 1, 2014Electrical system. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
• 10149381Oct 1, 2014Back-over prevention (rear camera). Side View Camera Does Not Display Picture. The side view camera does not display a picture: z After engaging reverse gear z Activating the side view camera via the switch on the center console near the gear shift CAUSE z Water (moisture) entering the cable assembly, causing corrosion on the pins in the connector(s) at the camera(s) z Poor cable connection to the camera(s)
• 10149379Oct 1, 2014Electrical system. Headunit-High: CID Is Blank and "NO SIGNAL" Is Displayed. Intermittently the Central Information Display (CID) is blank and "NO SIGNAL" is displayed on the CID. z Fault Code B7F8C3 "no response from CID (HW error: loss of CID communication)" is stored in the HU-H Note: If Fault Code E1C440 "Headunit Reset" is also stored in the HU-H, this Service Information is not effective! Follow relevant test plan using ISTA…
• 10149375Oct 1, 2014Electrical system. Service Action: Replace Instrument Cluster. The display in the instrument cluster is inoperative.
• 10149371Oct 1, 2014Electrical system. Horn(s) Fail to Work. While trying to activate the horn, one or both horns fail to work. One or more of the following fault codes can be stored in the FEM: "8044A3 - Wiring, horn short circuit to earth" "8044A4 - Wiring, horn short circuit to positive" "8044A5 - Wiring, horn relay is defective or short circuit to positive" Water has entered the horn and caused it to fail internally (shorted out).
• 10149365Oct 1, 2014Steering. Power-Assisted Steering Failure. The power-assisted steering fails with a warning lamp in the instrument cluster or a check control message in the Central Information Display. In some cases, the Dynamic Stability Control warning lamp (DSC) in the instrument cluster may also be illuminated. Failure of the power-assisted steering may be caused by various software-related issues.
• 10149363Oct 1, 2014Suspension. Front Suspension Ride Height Has Dropped. INFORMATION Damages due to outside influences are not covered under the terms of the BMW limited warranties.
• 10149355Oct 1, 2014Engine. . INFORMATION To properly diagnose the customer's complaint, the applicable test plan for the misfire faults stored in the DME must be performed to avoid repeat repairs. If a misfire fault is not stored in the DME memory and an engine related drivability complaint is received, follow the path below to manually start the misfire test plan (AT1214_TVD4_MISFIRE_20): 1. Perform a vehicle test. 2. Select "Function…
• 10149353Oct 1, 2014Engine cooling. N47T and N57T Diesels with SCR Efficiency Faults Stored. A. The Service Engine Soon lamp is on (MIL) with either or both of the following SCR efficiency faults stored in the DDE: 26F500 - SCR system, efficiency: Efficiency too low 26F600 - SCR system, efficiency: Efficiency too low B. In addition, a Check Control message of "Incorrect diesel exhaust fluid" may be displayed with "no start scenario countdown" active.
• 10149351Oct 1, 2014Engine cooling. Reduced Engine Performance. When driving with high outside ambient temperatures, repeated stop and go, or high-load operation over longer distances, the engine performance can be reduced. The air-conditioning system blower output may also be reduced, and in some circumstances, the compressor is switched off.
• 10149285Oct 1, 2014Engine cooling. Delivery Stop: Crankcase Failure. A Delivery Stop has been issued on certain 2015 model year vehicles with N20/N26 engines produced from September 4, 2014 through October 21, 2014. These vehicles may have a crankcase failure. Approximately 145 vehicles are affected.
• 10149282Oct 1, 2014Engine. Engine Damage Due to Debris in Oil Passages. After performing extensive engine repairs (e.g., cylinder head removal), the engine begins to knock and may lose power. Debris has entered the engine oiling passages during cleaning of the engine block and cylinder head mating surfaces during engine repair.
• 10148042Sep 1, 2014Visibility (wipers, defrost, mirrors), Electrical system. Top Rear Side View Camera Control Unit Rattles While Driving. While driving, a rattling-type noise is heard coming from the lower windshield area up behind the instrument panel (driver's side). CAUSE The TRSVC (Top Rear Side View Camera) control module support bracket is loose.
• 10148032Sep 1, 2014Equipment. "Service Action: Remove Front Bumper Air Inlet Panel. The front air cooling duct does not cool sufficiently. It may cause the engine to overheat, resulting in a Check Control message. Certain vehicles were manufactured with a ""sealed-off"" front air cooling duct. AFFECTED VEHICLES This Service Action involves F30 vehicles produced from June 26, 2014 to July 4, 2014. First check if a Service Action label with a…
• 10148381Aug 1, 2014Engine cooling, Equipment. Service Action: Replace Emission Label. Certain 2015 model year vehicles with N47T and N57T diesel engines were produced with an "emissions" label which contains incorrect information pertaining to the 2015 model year. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at VDCs will be repaired prior to dealer delivery.
• 10148380Aug 1, 2014Equipment. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue.
• 10148373Aug 1, 2014Equipment, Electrical system. Head-Up Display Inoperative. The Head-up Display is inoperative. Fault code 0xB7F6E3 - HUD: Communication error (HUD does not answer) is stored in the Instrument Cluster (KOMB25). A software error in the instrument cluster prevents the Head-up Display from activating.
• 10148371Aug 1, 2014Electrical system, Equipment. Vehicle Only Starts when Remote Key Held Against Column. The vehicle does not start using the Comfort Start feature. The vehicle does start once the remote key is held next to the steering column emergency start area (key symbol at the right side of the column between the white marks). The antenna (aerial) in the passenger compartment near the front of the center console has shorted wiring.
• 10148218Aug 1, 2014Fuel system. N20 and N26 Injector Replacement. INFORMATION When a defective high-pressure fuel injector is identified with an index "02" designation, as shown in the illustration below, all 4 injectors must be replaced at the same time. This bulletin only applies to index "02" injectors. Index "01" and index "03" or higher are not affected. No immediate repair is required unless the BMW vehicle is currently experiencing this…
• 10148135Jul 1, 2014Electrical system. ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical…
• 10148132Jul 1, 2014Forward collision avoidance. Front Collision Warning Check Control Message Displayed in CID. Occasionally while driving, a check control message (CCM) for Front Collision Warning is displayed in the Central Information Display (CID). This message is cleared from the CID by clicking on "OK" using the iDrive controller.
• 10148129Jul 1, 2014Equipment. Central Information Display Intermittently Dimming or Flashing Off/On. Intermittently the Central Information Display (CID) dims and/or flashes off/on. There are two possible root causes for this issue.
• 10148128Jul 1, 2014Equipment. Headunit High Is Constantly Resetting. After connecting a mobile device via Bluetooth, the Headunit High (HU-H) constantly resets. This is because the mobile device paired/connected to the vehicle contains one or more emails with 30 or more recipients. Note: In this situation, a reset is when the HU-H shuts down and then turns back on. CAUSE Software error in the HU-H.
• 10148120Jul 1, 2014Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10148117Jul 1, 2014Engine cooling. Exhaust Leak on Diesel Particulate Filters. An exhaust leak develops on the Diesel Particulate Filter (DPF) around the area of the flexible coupling. Age or wear on the flexible coupling
• 10148101Jun 1, 2014Electrical system. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
• 10148334May 1, 2014Exterior lighting. Active Headlight Control Malfunction in Both Headlights. AHL (Active Headlight Control) malfunctions on both sides. Both lights aim either up or down while driving. Fault Code 8041B6 is present. Broken mounting bolt holding on the rear height sensor bracket.
• 10148333May 1, 2014Electrical system, Engine. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster.
• 10148323May 1, 2014Latches, locks and linkages, Body and structure. Trunk Lid Does Not Open Completely. The customer may complain that the trunk does not open fully when using the remote key or hands-free trunk-lid opening (a Comfort Access function). CAUSE * A dry trunk lid seal causes the trunk lid to stick. * F30 and F32 only: A trunk return spring that is not installed correctly may not open the trunk lid fully.
• 10148321May 1, 2014Equipment. MF56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand.

← All problems reported for the 2015 BMW 320I