2013 BMW 740LI Technical Service Bulletins

310 technical service bulletins (TSBs) are on record for the 2013 BMW 740LI. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10150171Nov 1, 2013Equipment. Bang & Olufsen Sound System: Loudspeaker Cover Rattles. The top center loudspeaker cover rattles when driving on rough roads. CAUSE Poor loudspeaker cover fitment to the speaker assembly
• 10150166Nov 1, 2013Brakes. Incorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model.
• 10150161Nov 1, 2013Engine, Transmission and drivetrain. N55: Engine Difficult to Start at Cold Ambient Temperatures. The complaint may include any of the following symptoms: * The engine stalls immediately after a cold start before driving away * The engine may run roughly or misfire after a cold start * The engine does not start cold or may take several attempts * To assist starting when cold, the accelerator may need to be depressed slightly and the idle speed raised…
• 10150159Nov 1, 2013Engine, Transmission and drivetrain. MN16 Engine: FC 2D9B Knock Sensor, Signal Is Stored in the DME. Certain areas of the US experience extremely cold climate conditions during the winter months, which can cause the Service Engine Soon lamp to illuminate while the engine temperature is increasing to full operating temperature. The following fault may be stored in the DME: ??FC 2D9B Knock Sensor, Signal CAUSE Unfavorable DME knock sensor diagnostic at…
• 10150266Oct 1, 2013Seats. Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
• 10150263Oct 1, 2013Equipment. "IHKA Operating Panel Buttons Are Peeling. INFORMATION As noted in ETK: In case of surface damage to buttons, use the button cap repair kit. Use and claim the part number for the ""Repair kit for button caps"" when performing this repair. Replace ALL the buttons with those included in the kit.
• 10150257Oct 1, 2013Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or…
• 10150256Oct 1, 2013Fuel system. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME.
• 10152356Sep 1, 2013Electrical system. """Message"" Option Is Missing After Programming. Messages can be sent to the vehicle and are received as indicated by the envelope icon displayed in the CID. However, the menu option ""Message,"" used to retrieve or access messages, is no longer available in the iDrive menu. CAUSE Software error with ISTA/P 2.49.2 to 2.49.4 I-Level F001-13-03-503 to F001-13-03-505"
• 10152347Sep 1, 2013Fuel system. N55 Engine: Erroneous Service Engine Soon Lamp Illuminated with Mixture Faults Stored in the DME. INFORMATION An error has been identified in the current version of ETK regarding N55 fuel injector replacement part numbers and production dates. Installing the incorrect injector part number can lead to an erroneous Service Engine Soon lamp illumination and various mixture faults stored in the DME.
• 10152343Sep 1, 2013Engine cooling. "The customer complains that the ""low engine oil"" message is displayed too frequently. CAUSE The cause is related to, but not limited to, one or more of the following components and systems shown below: * Turbocharger * Crankcase ventilation * Engine gasket leaks * Internal engine tolerances and sealing * Improper filling or topping up Use the troubleshooting procedure below to help identify the cause."
• 10053583Sep 1, 2013Engine cooling. Bmw: malfunction indicator light (mil) illuminated indicating low engine oil. Dealers are to use the troubleshooting procedure to determine the problem and do the proper recommended repairs.
• 10150235Aug 1, 2013Equipment. HU-H: SDARS Radio Stations Cannot Be Stored in PRESET Menu. The SIRIUS/XM satellite radio (SDARS) stations cannot be stored in the PRESET menu. * No fault code related to this issue is stored in the HU-H. * AM/FM radio stations are not affected; they can be stored correctly. Software error in the SDARS control unit integrated in the Headunit-High (HU-H)
• 10150233Aug 1, 2013Equipment. ? Bang & Olufsen Sound System: Loudspeaker Illumination. One or more of the following situations may occur concerning the illumination of the Bang & Olufsen sound system loudspeakers: * Illumination is insufficient (not bright enough) * Illumination is not available on all loudspeakers * Brightness cannot be adjusted Loudspeaker illumination settings are dependent on the model: * Different brightness…
• 10150231Aug 1, 2013Electrical system. "FRM3 Will Not Communicate with ISTA. When diagnosing the vehicle with ISTA, the FRM3 (Footwell Module) is shown as not responding in the vehicle test. The customer may report one or more of the following malfunctions: 1. Light operation * CCM (Check Control Message) ""Display failure"" * Lighting INOP * Turn signal lights INOP * Break lights INOP * License plate light INOP * Courtesy lights INOP * Instrument…
• 10150219Aug 1, 2013Suspension. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
• 10150217Aug 1, 2013Engine cooling. The Service Engine Soon Lamp On with Post Oxygen Sensor Faults Stored. The Service Engine Soon (MIL) lamp is on and the following faults are stored in the DME fault code memory.
• 10150076Jun 1, 2013Electrical system. Condition Based Service Due Date Is Reset to 01/2000. The Condition Based Service (CBS) due date is reset to 01/2000 and cannot be updated for: * Oil Service * Check Vehicle Note: No fault code is stored Software error in the Instrument Cluster
• 10150070Jun 1, 2013Steering. Squeaking Noises when Steering Wheel Is Turned. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
• 10150069Jun 1, 2013Electrical system, Transmission and drivetrain. Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case control unit (Longitudinal Torque Module or LMV)
• 10149618May 1, 2013Equipment. iPhone Charging Status Constantly Switches On and Off. Do not replace any other parts! Advise the customer that he/she must use one of the following: * The original Apple iPhone/iPOD USB cable that came with the device * A BMW supplied iPhone/iPOD USB adapter cable PARTS INFORMATION Part Number
• 10149617May 1, 2013Electrical system. TCB: Emergency Call Is Erroneously Triggered. An emergency call is erroneously made with no input from the driver. The following fault codes are stored in the TCB: * 0xB7F325 - Emergency call loud speaker: break in circuit * 0xB7F319 - Emergency call button: short circuit * 0xB7F326 - Emergency call loud speaker: short circuit to earth * 0xB7F33E - Automatic emergency call triggered frequently CAUSE TCB control…
• 10149610May 1, 2013Equipment. Rattling/Grinding Noises from Center Console. When the heating and air conditioning system is first turned on, a grinding noise may be heard from the right side of the front center console. CAUSE The bushing of the blending flap for the rear seat outlet lacks sufficient grease.
• 10149608May 1, 2013Electrical system. "Service Action: Program Control Units (CAS). After programming/coding the vehicle with ISTA/P 2.48.1 or earlier, the Car Access System (CAS) was incorrectly coded. This causes the anti-theft alarm system panic button on the remote control to not function. In order to determine whether a specific vehicle has had this Service Action completed or is affected by this Service Action, first check the B-pillar label for…
• 10149597May 1, 2013Air bags. DSC Warning Light is On. The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for 'Chassis Control System failure' One or more of the following fault codes are stored: F25, F30 DSC * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit…
• 10149596May 1, 2013Brakes. Incorrect Remaining Service Life from CBS Data for Brake Pads. The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake pad thickness. The customer notices implausible remaining distances (too high or too low) on the front and/or the rear axle brake system. Software calculation of the brake pad wear model
• 10149593May 1, 2013Transmission and drivetrain, Electrical system. "The warning lamps for DSC, ABS and brake warning are illuminated. There may also be a warning in the control display for ""Chassis Control System failure."" One or more of the following fault codes are stored: DSC: * D36D44 - Signal error longitudinal torque distribution (LMV) * 48097D - Transfer Case clutch position open F01, F02, F07, F10, F12 and F13 LMV: * 440108 - Control Unit internal error * 44010F…
• 10149590May 1, 2013Engine, Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or…
• 10149589May 1, 2013Fuel system, Engine. "N54 Engine: Diagnosis of Cold Start Rough Running with Misfire Faults. The customer may complain that during the cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. Various misfire fault codes (e.g., 29CC, 29D2, 29D1, 29D0, 29C0, 29CF) may be stored in the DME control module. The engine rough running complaint can be reproduced on a cold start in the workshop.
• 10149581May 1, 2013Engine. Service Engine Soon Light Flashes with Throttle Adaptation Faults Stored. The EML light flashes with a check control message for reduced power output and/or the Service Engine Soon lamp (MIL) flashes. During the throttle valve adaptation (teach-in limit run), faults may occur due to signal voltage oscillations. This could lead to a termination of the teach-in routine or an incorrect value taught in at the lower…
• 10149491Apr 1, 2013Electrical system, Equipment. "Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed. Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. ??Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Hardware error in the Headunit-High"
• 10149488Apr 1, 2013Equipment. MRed or Blue Cap Missing from Temperature Control Wheel. The customer states the red or blue cap is missing from the temperature control wheel of the heat and air conditioning control panel.
• 10149342Apr 1, 2013Electrical system. Hill Descent Control Inoperative After Programming with ISTA/P 2.49.0 or 2.49.1. Hill Descent Control is inoperative after programming the vehicle with ISTA/P versions 2.49.0. or 2.49.1. Central Gateway Module software error.
• 10149336Apr 1, 2013Transmission and drivetrain. "Transmission Intermittently Goes into ""P"" or ""N"" after MSA Engine Start. The transmission can intermittently go into the Park (P) or Neutral (N) position after an MSA engine start without any customer influence. This problem is very sporadic, difficult to reproduce, and no relevant faults are stored. Unfavorable DME/EGS software"
• 10149335Apr 1, 2013Engine cooling. MService Action: Replace the Coolant Pump. Coolant is leaking from the coolant pump. CAUSE The coolant pump may develop cracks in the plastic housing. These cracks may result in a coolant leak.
• 10150135Mar 1, 2013Equipment, Electrical system. "TCB: Emergency Call Is Disabled. A Check Control message shows ""Emergency call failure."" When the SOS button is pressed, the call is not made by the TCB (Telematics Communication Box). Fault code 0XB7F33F is stored in the TCB. CAUSE TCB application error"
• 10150132Mar 1, 2013Air bags. CIS Seat Mat Replacement. Installation of a new CIS (capacitive sensing passenger occupancy mat) will not enable with ISTA/P. Wrong coding in the spare part from the supplier
• 10150130Mar 1, 2013Equipment. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
• 10150125Mar 1, 2013Equipment, Visibility (wipers, defrost, mirrors). "Whistling Noise Heard from the Center Fresh-Air Vent During Heating. A whistling noise is heard from the center fresh-air vents. The noise can be heard during the warm up phase (3 to 10 mins) after the heating system is first activated, with low outside temperatures and the center vents stratification adjustment wheel is turned to the ""red"" position. Note: This is independent of the air distribution setting, but…
• 10150114Mar 1, 2013Electrical system. Advanced Onboard Battery Diagnostics. INFORMATION Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery.
• 10150101Mar 1, 2013Fuel system, Engine. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ??While driving or…
• 10150099Mar 1, 2013Fuel system. N54 Engine: Fuel Pressure Control Test Plan Error. INFORMATION Not applicable.
• 10150096Mar 1, 2013Transmission and drivetrain, Engine. N55 Engine Failsafe - FC 120308 Boost Pressure Control, Plausibility: Pressure Too Low Stored in DME Fault Memory. INFORMATION The customer complains the SES is illuminated and the engine has reduced power (engine failsafe mode).
• 10149457Feb 1, 2013Equipment. Headunit High: Vehicle Position Is Incorrect on the Navigation Map. The vehicle position on the navigation map is incorrect. With route guidance active, the vehicle is displayed: * In an incorrect location Or * Outside the planned route The navigation system integrated in the Headunit High (HU-H) is not calibrated correctly.
• 10149456Feb 1, 2013Equipment, Visibility (wipers, defrost, mirrors). Bang & Olufsen Sound System: Loudspeaker Illumination. INFORMATION Do not replace parts and do not perform a repair attempt! Explain to the customer that loudspeaker illumination can vary from model to model. For an overview of the illuminated loudspeakers, refer to the attachment. IMPORTANT: The current version of the Owner's Manual for 5 Series vehicles is incorrect.
• 10149452Feb 1, 2013Electrical system. IHKA Operating Panel Buttons Are Peeling.
• 10149451Feb 1, 2013Exterior lighting. Moisture in LED Headlight.
• 10149449Feb 1, 2013Electrical system. Instrument Cluster Only Displays Background Image and Gear Indicator. The display in the instrument cluster intermittently only shows the background image and the gear indicator. * No fault code is stored * All gauges function correctly Note: The issue is rectified after a sleep mode cycle (ignition off for approx. 16 minutes). Software error in the instrument cluster introduced with software I-level 12-03-500 or…
• 10149446Feb 1, 2013Electrical system. Advanced Onboard Battery Diagnostics. Starting with the introduction of the F10 (5 Series), an advanced intelligent battery sensor has been used. This now makes it possible for the vehicle to monitor the condition of the battery in order to determine if the battery needs to be recharged or replaced, along with the remaining capacity of the battery.
• 10149310Jan 1, 2013Exterior lighting. Check Control Message "Automatic Headlight Adjustment Failed". One or more of the following Check Control Messages (CCM) will be displayed on the Central Information Display (CID): * Adaptive light system defective * Front left or right lighting system defective * Automatic headlight range adjustment defective Additionally, one or more of the following symptoms may occur: * Both low-beam headlamps point in the…

← All problems reported for the 2013 BMW 740LI