2014 BMW I3 Technical Service Bulletins

313 technical service bulletins (TSBs) are on record for the 2014 BMW I3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10151008Jan 1, 2016Tires, Wheels, Body and structure. SI B36 04 14 Wheels and Tires January 2016 Technical Service. This Service Information bulletin supersedes SI 36 04 14 dated September 2014. SUBJECT: Rolling Tire Noise . INFORMATION: You will find that driving an i3 is very similar to driving the conventional cars and trucks you're used to drive, but turn the "Readiness" ON and you'll immediately notice the silence from the powertrain. Once you'll pull away…
• 10150907Jan 1, 2016Steering, Equipment. Steering wheel rubs/brushes against the steering column trim. When the steering wheel is moved, it rubs/brushes against the steering column trim. CAUSE Rear steering wheel trim.
• 10150906Jan 1, 2016Steering, Equipment. Noises when turning the steering wheel. There are squeaking noises from the steering spindle when the steering wheel is turned. The steering spindle sleeve's plastic bearing is insufficiently lubricated or not lubricated at all.
• 10147869Dec 1, 2015Steering. This Service Information bulletin supersedes SI 32 06 14 dated January 2015. designates changes to this revision SUBJECT Noises and/or Play Around Steering Column. Rattling and/or clunking noises can be heard around the steering column; and/or a relatively large amount of play can be felt in the steering wheel when it is moved up and down. Excessive steering column tolerances
• 10147838Nov 1, 2015Electrical system, Equipment. Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
• 10147833Nov 1, 2015Equipment, Electrical system. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147824Nov 1, 2015Electrical system, Equipment. Clicking Noise from Off-board Charger. While the vehicle is charging, the off-board charger is clicking. The clicking noise comes from the relays inside the charger cycling off and on. This condition most commonly occurs when the vehicle is fully charged; it is plugged into the charger; and then pre-conditioning is activated via the BMW iRemote app. The cycling of the relays can last from a few seconds to several…
• 10147821Nov 1, 2015Body and structure, Engine cooling. ?SI B22 01 15 November 2015 Engine and Gearbox SuspensionTechnical Service This Service Information bulletin supersedes SI B22 01 15 dated February 2015. designates changes to this revision SUBJECT Left Side Engine Mount Broken. The left side motor mount or motor mount support has failed. As a result, the electric drivetrain moves excessively in the chassis. A banging noise can be heard from the rear of the vehicle…
• 10147815Nov 1, 2015Electrical system, Engine cooling. Various Software Fixes and Improvements. A number of undesirable conditions exist in these vehicles. This bulletin addresses the following customer complaints, system faults and improvements: ? Broken motor mount potential - (i3, SI B22 01 15) ? Low Cost Charging complaints - (i3) ? Vehicle will not charge at a power level below 600 watts - (i8) ? EME FC - 2228B8 (i8) ? EME FC - 2228BF (i3 & i8, SI B12 28 15) ? EME…
• 10147812Nov 1, 2015Engine, Electrical system. "Service Engine Soon (MIL) - RDME FC 128002. The Service Engine Soon light (MIL) is illuminated in the instrument cluster and fault code 128002 ""Air mass: Too low"" is stored in the RDME. CAUSE RDME software."
• 10147811Nov 1, 2015Electrical system. "EME Fault Code: 222011. ? It is not possible to engage any drive position and/or the display on the gear selector switch (GWS) returns back to ""P"" and ""P"" begins to flash. ? Check Control Messages (CCM): 170 ""Drivetrain fault!"" and/or 633 ""Drivetrain fault!"" is displayed in the instrument cluster. ? Fault code 222011 ""Electrical machine, rotor position sensor, signal: Rotor position sensor adjustment not…
• 10147810Nov 1, 2015Electrical system. "EME Fault Code: 2228BF. Check control message (CCM) 170 ""Drivetrain fault"" is displayed in the instrument cluster and fault code 2228BF ""EME: internal fault (drive position monitoring)"" is stored in the Electrical Machine Electronics (EME). This could also be accompanied by EME fault code 222852 ""Gear position actuator, monitoring parking lock position: P incorrectly engaged"". CAUSE EME software."
• 10147809Nov 1, 2015Electrical system, Engine. "Service Engine Soon (MIL) - IHKA FC 801375. The Service Engine Soon light (MIL) is currently or intermittently illuminated in the instrument cluster and fault code 801375 ""Electric auxiliary heater (high voltage) is stored: Temporary fault detected after software reset ""is stored in the Automatic Climate Control (IHKA). CAUSE IHKA software or Electric Heater (EH)."
• 10147771Oct 1, 2015Tires. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147768Oct 1, 2015Steering. "Steering Wheel Does Not Return to Center. INFORMATION Do not replace any parts for this complaint. The return behavior is inherent in the design of the EPS. An EPS ""break in"" period of approximately 2000 miles is required. Once this phase is completed, the level of friction is significantly reduced and no longer affects the return to center. Please use this information to educate the customer on the ""break in""…
• 10147257Sep 1, 2015Steering. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
• 10147246Sep 1, 2015Latches, locks and linkages, Body and structure. A Check Control Message is displayed for the Tailgate Lock Open. A Check Control Message is displayed indicating that the tailgate is open, even though it is mechanically closed. CAUSE Faulty tailgate lock or incorrect adjustment.
• 10147243Sep 1, 2015Tires. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10151405Aug 1, 2015Suspension. Front Axle Noise when Turning at Low Ambient Temperatures. A grating and/or squeaking noise from the front axle occurs when turning at low speeds or idle. The noise is most noticeable at low temperatures (approx. 32 degrees F), but not unusual at higher temperatures and after driving. Friction between the spring pad and the strut upper support bearing is causing the noise.
• 10147211Jul 1, 2015Equipment. NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick…
• 10147208Jul 1, 2015Electrical system. "Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the vehicle is capable of achieving on a full charge has not changed. The difference between the displayed range and actual range is always conservative, yet this difference…
• 10147207Jul 1, 2015Electrical system. Charging is not Possible, or is Reduced. ? Charging is no longer possible, or is only possible with restricted charging power, or: ? When charging the vehicle, the indicator light around the charging socket lights up red and the external circuit breaker (inside the A/C charger or A/C power supply) activates. CAUSE Hardware fault in the Electric Motor Electronics (EME), or the Convenience Charging Electronics (KLE).
• 10147202Jul 1, 2015Equipment. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the…
• 10147191Jul 1, 2015Engine. "Service Engine Soon (MIL) Lamp Illuminated with No Relevant Faults. INFORMATION If an i3 or i8 is brought in for service with a Service Engine Soon (MIL) lamp illuminated, or with a customer concern that the MIL is intermittently illuminated, troubleshoot with ISTA/D. During diagnosis, refer to the functional description (FUB), Troubleshooting Malfunction Indicator Lamp I01.
• 10147718Jun 1, 2015Electrical system. "High-Voltage Charging Cable Lock Malfunction. One of the following situations can occur: ? The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. ? The high-voltage charging cable cannot be unlocked and disconnected.
• 10147717Jun 1, 2015Steering. Grinding Noise from Steering Wheel when Turning. The customer complains of a noise from the steering wheel while driving. Due to insufficient gap, the steering column lower shroud rubs against the steering wheel.
• 10147716Jun 1, 2015Tires, Wheels. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147708Jun 1, 2015Engine, Electrical system. Service Engine Soon (MIL): EME FC CF948C. The Service Engine Soon light (MIL) is intermittently illuminated in the instrument cluster (Kombi). This does not affect drivability, and no symptoms are apparent to the customer. CAUSE The following fault code is stored in the fault memory of the Electric Machine Electronics (EME): ?
• 10058424Jun 1, 2015Tires. Bmw: some vehicles experiencing the failure of tire pressure monitor (rdci) due to remote control unit hardware (fbd3 antenna) and needs repairing. Model years 2014-15.
• 10147154May 1, 2015Equipment. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147148May 1, 2015Exterior lighting. "Traces of Condensation Appear in Rear Tailgate Lights After removing the rear circuit board, dry out the lens area with an adjustable temperature heat gun. It is important that the temperature not be higher than 140 F, to avoid damage to the lens and LED. . INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
• 10147147May 1, 2015Electrical system. "Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the vehicle is capable of achieving on a full charge has not changed. The difference between the displayed range and actual range is always conservative, yet this difference…
• 10147145May 1, 2015Electrical system. "High-Voltage Charging Cable Lock Malfunction. One of the following situations can occur: ? The vehicle cannot be charged via the high-voltage charging procedure. The indicator light on the charging socket lights up white and does not change colors. ? The high-voltage charging cable cannot be unlocked and disconnected.
• 10147144May 1, 2015Electrical system. "Charging Stops when Using ""Occasional Use"" Cable. When charging the vehicle with the Occasional Use Cable (OUC), and the charge rate set to ""Min"" in the CID, charging may switch off during the charge cycle. In rare cases, the vehicle may not start the charging cycle at all.
• 10147139May 1, 2015Equipment, Body and structure. Front Door Trim Panel Loose. The door trim panel is loose or has a visible gap in the area near the B-pillar. The yellow door trim panel securing clips are not robust.
• 10147136May 1, 2015Tires, Wheels. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc.
• 10147129May 1, 2015Engine, Electrical system. "Service Engine Soon (MIL): RDME FC 120006. The Service Engine Soon light (MIL) is intermittently illuminated in the instrument cluster, and fault code 120006 ""Information engine switch-off time: too long compared to cooling of engine coolant"" is stored in the RDME. CAUSE Software error, faulty component, or cooling issue"
• 10058477May 1, 2015Equipment. Bmw: some vehicles experience high voltage charging cable not able to disconnect and/or unlock, charging socket lights up white and fails to change colors and not able to charge via high voltage charging procedure. Model 2014 i3.
• 10193495Apr 6, 2015Visibility (wipers, defrost, mirrors). The customer complains of rattling noises from the rear window when driving on rough roads.
• 10152319Apr 1, 2015Equipment. The model year is incorrect on the emissions compliance label on certain I01 and I12 vehicles produced from November 1, 2014 through December 22, 2014. In order to remedy the situation, BMW is conducting a Voluntary Emissions Recall Campaign to replace the emissions compliance label on all affected vehicles.
• 10152315Apr 1, 2015Electrical system. "Airbag Warning Light ON: Fault 930BE8, High-voltage System Shutdown. The airbag warning light in the instrument cluster is on, or the check control message (CCM) ""Restraint system faulty"" is displayed. The advance crash safety module (ACSM4I) has fault code 930BE8 ""High-voltage system switch-off Range extender Electrical Machine Electronics (REME)/battery management electronics: Resistance too high"" stored.
• 10152313Apr 1, 2015Transmission and drivetrain. Drivetrain Malfunction (CCM 794) with Isolation Faults. The Drivetrain Malfunction check control message (CCM 794) is displayed, either while driving or when starting up. The following faults are stored in the vehicle: EME: 22280F and/or 222814 SME: 21F0E3 and/or 21F0E4 When the CCM is present, there are no apparent drivability concerns. After allowing the vehicle to rest and then restart, the CCM typically does…
• 10152312Apr 1, 2015Electrical system. "?SI B61 35 14 General Electrical Systems April 2015 Technical Service This Service Information bulletin supersedes SI B61 35 14 dated March 2015. designates changes to this revision SUBJECT Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update.
• 10152298Apr 1, 2015Equipment. ?SI B00 06 14April 2015 Maintenance and General HintsTechnical Service This Service Information bulletin supersedes SI B00 06 14 dated March 2015. designates changes to this revision SUBJECT BMW Early Warning Information Program.
• 10147690Mar 1, 2015Equipment. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us…
• 10147688Mar 1, 2015Air bags. "Airbag Warning Light ON: Fault 930BE3, High-voltage System Shutdown. The airbag warning light in the instrument cluster is on, or the check control message (CCM) ""Restraint system faulty"" is displayed. The advance crash safety module (ACSM4I) control has fault code 930BE3 ""High-voltage system switch-off (EME/convenience charging electronics/auxiliary battery): Resistance too high"" stored. A sporadically poor…
• 10147685Mar 1, 2015Electrical system. "General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 35 14 dated December 2014. designates changes to this revision SUBJECT Displayed Range Is Lower After Programming. After the vehicle is programmed with ISTA/P 3.53.3 (i-level I001-14-07-503), the displayed vehicle range in the instrument cluster is lower than prior to the software update. The actual range that the…
• 10147683Mar 1, 2015Electrical system. 12-volt Battery Terminal Adapter Slightly Loose. The 12-volt battery adapter appears to be slightly loose. The cable connection on the positive or negative terminal can be slightly moved or turned. It is normal for vehicles to have slight play in the adapter for battery connections. Vehicles produced prior to April 3, 2014 may have excessive play because the mounting screw is not microencapsulated and can loosen…
• 10147677Mar 1, 2015Body and structure. Groaning Noise when Opening and Closing Rear Doors. INFORMATION Covered under the terms of the BMW New Vehicle/SAV Limited Warranty. Repairing One Side https://www.bmwtis.net/tiscode/cgi-bin/bulletin.aspx?sie_path=/tsb/bulletins/htm_store/220...4/6/2015
• 10147670Mar 1, 2015Transmission and drivetrain. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. SUBJECT Service Action: Replace Park Lock Actuator. Unfavorable tolerances in the park lock actuator may lead to a functional failure or unusual noises when it is activated. As a result, the park lock actuator must be replaced on affected…

← All problems reported for the 2014 BMW I3