2014 BMW X6 Technical Service Bulletins

185 technical service bulletins (TSBs) are on record for the 2014 BMW X6. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10147192Jul 1, 2015Fuel system. "?SI B13 02 15July 2015 Fuel SystemsTechnical Service This Service Information bulletin supersedes SI B13 02 15 dated May 2015. designates changes to this revision SUBJECT Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output. This Service Action involves F01, F02, F04, F07, F10, F12, F13, E70, E71, and E72…
• 10059004Jul 1, 2015Engine, Electrical system. Check control message (ccm) "drive faulty; drive at moderate speed" will display and engine power may go down when accelerating under certain conditions due to dme software error.
• 10147724Jun 1, 2015Equipment. iDrive Controller Trim Peeling. The chrome ring on the iDrive controller is peeling. Poor chrome material adhesion.
• 10147722Jun 1, 2015Electrical system. "BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles…
• 10058488Jun 1, 2015Equipment. Bmw: the chrome material adhesion is poor and causes chrome ring to peel on idrive controller and needs to be replaced.
• 10058424Jun 1, 2015Tires. Bmw: some vehicles experiencing the failure of tire pressure monitor (rdci) due to remote control unit hardware (fbd3 antenna) and needs repairing. Model years 2014-15.
• 10147136May 1, 2015Tires, Wheels. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc.
• 10147131May 1, 2015Fuel system. Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
• 10147127May 1, 2015Engine. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10147125May 1, 2015Engine. N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ?
• 10147123May 1, 2015Electrical system. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer.
• 10152301Apr 1, 2015Equipment. "This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance.
• 10058483Apr 1, 2015Fuel system, Other or unknown. Bmw: procedural information on the installation of fuel system low pressure sensor and not correctly installed will lead to failure of low pressure sensor and metal supply line. Model 2008-14.
• 10058467Apr 1, 2015Engine, Electrical system, Fuel system. Bmw: fuel gauge fails to show correct level of fuel when filling fuel tank but would update itself after driving awhile and illumination of engine malfunction lamp (mil) comes on, due to software error in instrument cluster. Model 2011-15.
• 10147669Mar 1, 2015Transmission and drivetrain. Driveshaft Technical Service. This Service Information bulletin supersedes SI B26 01 14 dated August 2014. PERFORM THE PROCEDURE OUTLINED IN THIS SERVICE INFORMATION ON ALL AFFECTED VEHICLES BEFORE CUSTOMER DELIVERY OR THE NEXT TIME THEY ARE IN THE SHOP FOR MAINTENANCE OR REPAIRS. designates changes to this revision SUBJECT Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may…
• 10147660Mar 1, 2015Equipment, Electrical system. "SI B12 10 15 Engine Electrical Systems March 2015 Technical Service This Service Information bulletin supersedes SI B12 10 15 dated January 2015. designates changes to this revision SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) did not work correctly with ISTA/P 3.54.x or 3.55.0.
• 10147656Mar 1, 2015Engine. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10147655Mar 1, 2015Engine. "N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
• 10058494Mar 1, 2015Latches, locks and linkages, Body and structure. Door opens, while driving, to first stage, causing check control message to be displayed
• 10058491Mar 1, 2015Transmission and drivetrain, Engine, Engine cooling. Front drive shaft universal joints may wear out prematurely
• 10147085Feb 1, 2015Electrical system. "SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the…
• 10147068Feb 1, 2015Engine. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT…
• 10147067Feb 1, 2015Electrical system. This Service Information bulletin supersedes SI B07 03 14 dated February 2015. designates changes to this revision SUBJECT Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause.
• 10057707Feb 1, 2015Air bags, Interior lighting. Bmw:some bmw models may or may not display airbag warning light.
• 10147624Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
• 10147623Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts…
• 10147602Jan 1, 2015Fuel system, Engine. SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL)…
• 10147600Jan 1, 2015Equipment, Engine. "SUBJECT N63: CBS Oil Service Conversion in ISTA/P. The CBS oil service conversion being performed for the N63 Customer Car Package and timing chain check (SI B11 16 14) does not work correctly. It does not change the interval to the desired 12 months/10,000 miles for the vehicles listed above in the specified production ranges. The ""Conversion, oil service 12months/15,000km/10,000 miles"" is working properly for…
• 10147595Jan 1, 2015Electrical system, Engine. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles.
• 10147593Jan 1, 2015Engine, Equipment. "This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel…
• 10148194Dec 1, 2014Equipment, Electrical system. iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z…
• 10148184Dec 1, 2014Equipment, Electrical system. BMW Maintenance Program: 12-Volt Battery Replacement Measure.
• 10148172Dec 1, 2014Engine cooling. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: ? During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. ? During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated.? While driving or…
• 10148163Dec 1, 2014Engine cooling. N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure to check the engine timing chains for wear and should be completed in conjunction with SI B11 06 14 "N63 Customer Care Package". Performing the test plans identified in the procedure below will detect wear at an early stage and if necessary provide a repair solution. To avoid future valvetrain wear, the vehicle must be reprogrammed…
• 10148161Dec 1, 2014Engine cooling. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its "class leading" power and performance.
• 10058271Dec 1, 2014Electrical system. Bmw: in high frequency range of 104mhz-107mhz, noise interference from the radio is affected by brakes being applied, due to left rear taillight having faulty hardware. Model 2014 f16 (x6).
• 10058163Dec 1, 2014Equipment. Bmw f16: bulletin information regarding radio reception interference due to taillight.
• 10057717Dec 1, 2014Equipment. Bmw: bmw x6 models are experiencing radio interference because of taillight.
• 10148423Nov 1, 2014Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10149382Oct 1, 2014Electrical system. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: z Call disconnection z Contact List incomplete z General connection failures Apple software iOS 7 and its variants
• 10149279Oct 1, 2014Equipment. Diagnosing Stored Fault Codes to Help Avoid Repeat Repair Visits. Analysis of FASTA data and repeat repair visit reports indicates that there are many fault codes that are stored in the above vehicles, but they are not diagnosed to identify their root cause. Fault codes that are not diagnosed to find their root cause can lead to a repeat repair visit to the workshop by the customer.
• 10148034Sep 1, 2014Electrical system, Transmission and drivetrain. "Intelligent Battery Sensor Diagnosis Hints. The vehicle enters the workshop with one or more of the following complaints: * Check Control Message related to battery discharge * No-start condition * Consumer power reduction (reduced blower speed, heated seats operation, etc.) * The following fault codes may be stored in the DME a. 2E8B - Intelligent battery sensor, signal b. 2E8C - Intelligent battery sensor…
• 10148219Aug 1, 2014Transmission and drivetrain. Service Action: Inspect Front Driveshaft. The universal joints in the front driveshaft may wear out prematurely.
• 10148135Jul 1, 2014Electrical system. ConnectedDrive/BMW Assist System Diagnosis Information. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information bulletin is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. This Service Information bulletin will assist you both in identifying the issue and providing technical…
• 10148120Jul 1, 2014Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.
• 10148087Jul 1, 2014Engine cooling. External Engine Oil Leaks and Repairs. During the vehicle's operational life, normal engine oil seepage or sweating, in addition to accumulated road dust, dirt and grime in the engine compartment can cause the appearance of a more severe oil leak. This is further exaggerated by residual oil that remains on the engine assembly after maintenance services are performed, e.g., oil filter changes, "engine oil top-offs,"…
• 10148101Jun 1, 2014Electrical system. iPhone: Connection Failures with iOS 7. There are various connectivity failures with the iPhone using iOS 7. Some examples are listed below: * Call disconnection * Contact List incomplete * General connection failures CAUSE Apple software iOS 7 and its variants.
• 10148308May 1, 2014Fuel system. N63 and S63 Engine: High-pressure Fuel Injector Replacement Procedures. The customer complains that one of the following scenarios has been encountered while operating the vehicle: * During a cold start in the morning, the engine runs very roughly and the Service Engine Soon lamp is illuminated. * During a hot start, the engine runs very roughly and the Service Engine Soon lamp is illuminated. While driving or…
• 10148276Apr 1, 2014Equipment. Traffic Information Is Inoperative. The traffic information is intermittently or permanently inoperative. * Traffic flow is not displayed on the navigation map. * The traffic list is empty. 1. The Offboard Availability (backend) system is unavailable and is not sending traffic information. 2. The traffic information feature is not activated correctly.
• 10148273Apr 1, 2014Equipment, Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts.

← All problems reported for the 2014 BMW X6