2018 Chevrolet Silverado 1500 Technical Service Bulletins

1,235 technical service bulletins (TSBs) are on record for the 2018 Chevrolet Silverado 1500. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10151874Nov 26, 2018Equipment, Body and structure. This Preliminary Information communication provides the technician with weight capacity for the tailgate and cargo loops in the bed.
• 10212576Nov 21, 2018Fuel system. Service Update (Population Expansion Message). Certain vehicles may have one or multiple DTCs that are incorrectly illuminating the service engine soon (SES) light. Hardware including fuel injectors and exhaust gas recirculation (EGR) valves may have been used to fix this issue, however, the condition could return after these repairs were made. There is no effect for vehicle performance.
• 10151868Nov 21, 2018Equipment. This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
• 10151863Nov 19, 2018Engine, Steering. This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
• 10151849Nov 15, 2018Electrical system. This Preliminary Information communication provides information to the technician of additional information when diagnosing a service driver assist message with a diagnostic trouble code B172E and or a B172F. The haptic seat motor has a pigtail lead coming off of it. In many cases the wiring pigtail near the haptic seat motor has broken and will require replacement.
• 10212574Nov 14, 2018Fuel system, Engine cooling. Service Update. Certain vehicles may have one or multiple DTCs that are incorrectly illuminating the service engine soon (SES) light. Hardware including fuel injectors and exhaust gas recirculation (EGR) valves may have been used to fix this issue, however, the condition could return after these repairs were made. There is no effect for vehicle performance.
• 10151842Nov 14, 2018Electrical system. This Preliminary information communicates a normal DIC message after learning keys/fobs which indicates the drivers memory position.
• 10151830Nov 13, 2018Body and structure, Visibility (wipers, defrost, mirrors). This Preliminary Information communication provides information to the technician about vehicles that may have a whistle noise in the vehicle from the driver or passenger side. Technician will need to inspect for voids in the body sealer on the left or right side A-pillar. Technician should also inspect for voids in the body sealer at the cowl seam and apply sealer as necessary.
• 10155111Nov 8, 2018Engine. This informational bulletin provides information on characteristics of the new engine versus the old engine.
• 10155079Nov 7, 2018Equipment. This engineering informational bulletin is requesting information from the field on vehicles that have the condition of A/C Not Cool Due to No Pressure Build.
• 10155078Nov 7, 2018Wheels, Body and structure. This engineering informational bulletin is requesting information from the field on vehicles that have the condition of Missing/Wrong Wheel Trim Shipped with New Vehicle.
• 10151817Nov 2, 2018Engine. This Preliminary information communicates to the dealer an issue where the vehicle's service engine soon light may illuminate due to trouble codes P0601-P0604, P0606, P062B, P062F, P0630, P16F3, or P262B . The dealer is to inspect the engine control module's electrical connections and for proper powers and grounds. Dealer instructed to replace the Engine Control Module, if no other issues found.
• 10155080Nov 1, 2018Equipment. This engineering informational bulletin is requesting information pictures of windshield, steering wheel and/or door trim panel for product issues covered under warranty.
• 10147392Oct 19, 2018Brakes. This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and…
• 10145501Sep 19, 2018Transmission and drivetrain. This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
• 10145486Sep 14, 2018Suspension. This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer…
• 10145479Sep 13, 2018Brakes. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have issues were the customer will need increased effort to depress the brake pedal. Technician may find fluid in the brake booster and/or the booster vacuum line. Technician will need to replace Vacuum Pump, Brake Booster, Master Cylinder, Vacuum Pump Belt and the Vacuum Line…
• 10187431Aug 8, 2018Equipment. This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
• 10186122Aug 8, 2018Equipment. This technical bulletin provides a procedure to replace the dehydrator to correct the condition of A/C Inoperative and/or Insufficient Cooling due to the seals going bad within the part.
• 10143459Jun 27, 2018Equipment, Engine. This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
• 10143438Jun 12, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern ofDTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
• 10143434Jun 12, 2018Steering. This Preliminary information communicates a repair procedure for a squeak/squawk type noise coming from the lower column/drivers foot well area when turning. It explains how to properly lubricate the column shaft boot where the shaft interacts with the boot where it passes through the boot.
• 10143430Jun 12, 2018Suspension, Body and structure. This Preliminary Information communication provides information to the technician about vehicles that have a creak, click, pop, and or crack type noise from the front suspension or front frame area while making tight turns. Technician will need to loosen and then re-torque the four front frame cross member nuts and bolts.
• 10143424Jun 6, 2018Engine cooling. This Preliminary information communicates. A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
• 10141379May 30, 2018Seats, Equipment. This Preliminary Information communication provides information to the technician about vehicle that may have a front driver's or passenger's seat back may lean or be turned outward. Technician will need to remove the seat bottom trim cover and reinstall it completely and squarely to the cushion to correct the concern.
• 10141372May 24, 2018Electrical system, Brakes. This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and/or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct…
• 10141370May 22, 2018Steering, Equipment. This Preliminary information communicates to the dealer a condition where a tick noise may be present inside a vehicle while driving. This may be the result of a deformed or improperly seated steering shaft seal allowing engine compartment sounds into the vehicle. Dealers are instructed to replace or reinstall the boot as needed and are informed the condition is being reviewed by engineering.
• 10141367May 22, 2018Electrical system. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicle that may have a "Check Trailer Wiring" or "Service Trailer Brake System” message on the Driver Information Center when a trailer is connected to the vehicle. Diagnostic Trouble Code C1114 set in the Chassis Control Module. Chassis Control Module has to determine the type of trailer brake…
• 10141365May 18, 2018Equipment, Engine cooling. This Preliminary information communicates A vehicle may have a concern of DTCP050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause: Coolant getting into the cylinders, and provides direction for the repair.
• 10141362May 17, 2018Electrical system, Equipment. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the Generator Control Module (GCM). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance
• 10141351May 11, 2018Forward collision avoidance. This Preliminary information communicatesa "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when theFAB has been set to "Alert".
• 10141343May 1, 2018Equipment, Electrical system. This Preliminary information communicates that some technicians may find no refrigerant or a low refrigerant charge. Engineering is currently investigating this issue.
• 10137514Apr 23, 2018Steering, Electrical system. This Preliminary information communicates a power steering control module calibration error that does not allow its DTC's to transition to history and they always stay current, which can mislead a technician diagnosis. Dealers are to reprogram the power steering control module with updated calibration which will allow DTC's to transition to history if the issue that caused the DTC(s) are now longer present.
• 10137209Mar 28, 2018Engine. This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (L83), 5.3L (L86), 6.2L (LV3) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.
• 10137207Mar 27, 2018Back-over prevention (rear camera). This Preliminary Information communication provides information to the technician about vehicles that may have a diagnostic trouble code U0159 set in the instrument panel cluster and /or the body control module. For vehicles equipped with Ultrasonic Park Assist System Regular Production Option Code UD5 or UD7 technician will use Service Programming System to reprogram the Parking Assist Control Module to correct…
• 10137199Mar 26, 2018Wheels. This Preliminary Information communication provides information to the technician about removing the tinnerman push nuts when installing the accessory Accessory 22" Wheels Regular Production Option Code (SES, SEU, SEY, OR SEZ) or production 22" wheels Regular Production Option Code (RPT or SMI) also during any service requiring wheel removal.
• 10137197Mar 22, 2018Engine cooling. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
• 10137306Mar 9, 2018Body and structure, Visibility (wipers, defrost, mirrors), Electrical system. This technical bulletin provides a procedure to replace the drivers front door window regulator motor and door wiring harness if water and/or corrosion is found in the connectors.
• 10137382Mar 7, 2018Equipment. This informational bulletin provides the dealership with how to prep a vehicle for delivery to the customer to aid in higher CSi scores.
• 10137378Feb 26, 2018Electrical system, Equipment. This informational bulletin provides information to the customer on the radio display "info pages" being blank and to make sure to select in the "active info pages" menu.
• 10137330Feb 15, 2018Exterior lighting. This technical bulletin provides repair information to correct a customer concern of a headlamp bezel loose or falling off.
• 10129868Feb 7, 2018Engine. This Preliminary information communicatesP0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
• 10137369Feb 2, 2018Engine cooling, Fuel system. This technical bulletin provides a procedure to Add 1 quart of coolant to the upper chamber of the surge tank in order to bring the level up to the bottom of the fill neck to correct a condition of the coolant surge tank appears low and/or a low coolant message displayed intermittently due to the fill process at the plant cannot purge all of the air from the cooling system and surge tank.
• 10129106Jan 31, 2018Electrical system. This Preliminary Information communication advises the technician that the Technical Assistance Center TAC has a part restriction for the A15, Starter Generator (MGU). The dealer technician is advised to call the GMTechnical AssistanceCenter for further assistance.
• 10137268Jan 26, 2018Fuel system. This technical bulletin provides a procedure to replace the fuel tank and internal parts if found expanding and contacting the drive shaft.
• 10129101Jan 26, 2018Electrical system. This Preliminary information communicates that water leaking into the headlamp assembly or headlamp assembly connections can cause an electrical short which will keep modules from shutting down causing a dead battery and a no crank condition, a crank no start,or unable to program the engine control module. Engine control module will set a diagnostic trouble code of P1682, or the engine will continue to run with the…
• 10129091Jan 24, 2018Engine cooling. This Preliminary information communicatesA vehicle may have a concern ofDTCP050D settingalongwith a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. CauseCoolant getting into the cylinders, and provides direction for the repair.
• 10129075Jan 18, 2018Back-over prevention (rear camera). This Preliminary Information communication provides information to the technician about vehicles that have a Harsh Shift 1/2 and 2/3 and Sputter Applying Throttle Between 0 and 30%, Rough idle. Technician may find Diagnostic Trouble Codes P0101, P0171, P0172, P0174, and or P0175. Technician should inspect for cast flashing near the Mass Air Flow sensor as seen below.
• 10129050Jan 3, 2018Equipment. This Preliminary Information communication provides information to the technician about vehicles that the engine may run hot with the snow plow installed. Do not exceed 64 kilometers per hour / 40 miles per hour with a snow plow mounted to the vehicle even if equipped with VYU. The vehicle could overheat and be damaged.
• 10126993Dec 21, 2017Body and structure. This Preliminary information communicates and issue with the hood ajar message being displayed when the hood is not ajar. Inspect the body ground strap to insure it is connected in the proper locations and the strap eyelets are tight and do not rotate.

← All problems reported for the 2018 Chevrolet Silverado 1500