2023 Ford Explorer Technical Service Bulletins

164 technical service bulletins (TSBs) are on record for the 2023 Ford Explorer. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10233922Mar 28, 2023Electrical system. 2020-2023 Explorer/Aviator with start/stop push button ignition switch may exhibit an illuminated malfunction indicator lamp (MIL) and powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) B108A:01 (general electrical failure), B108A:24 (signal stuck high), and/or B108A:9E (stuck on). The ignition mode light emitting diode (LED) indicator may also flash quickly.
• 10233743Mar 17, 2023Transmission and drivetrain. 2023 F-150/Escape/Explorer/Maverick vehicles equipped with a full hybrid electric vehicle (FHEV) powertrain may exhibit diagnostic trouble codes (DTCs) P0A7D and/or P0DE6 and the vehicle identification number (VIN) is not recognized by the Midtronics xRC-3363 High Voltage Battery Rescue Charger. The technician will need to manually enter the vehicle charging mode by selecting 2022 model year, then enter the make…
• 10233738Mar 15, 2023Equipment. Some 2020-2023 Ford and Lincoln SYNC3 equipped vehicles may experience an inaccurate notification in the FordPass®/LincolnWay® app indicating Vehicle Has Entered Deep Sleep Mode. Vehicle Has Entered Deep Sleep Mode message is expected if the vehicle has not been started for 14 consecutive days, battery voltage is at/below 9.5 volts or the body control module (BCM) 12 volt battery state of charge (SoC) drops…
• 10233725Mar 14, 2023Transmission and drivetrain. Some 2020-2023 Explorer/Aviator 4x4/AWD vehicles with hybrid powertrain may experience a harshness and/or vibration felt through the seat, steering wheel and/or center console after initial driveaway between 25-50 MPH (40-80 Km/h) that lessens after driving 5-10 minutes. This may be due to driveshaft center bearing bounce mode during cold ambient temperatures. To resolve the concern, install a softer durometer…
• 10233591Mar 14, 2023Equipment. Some 2022-2023 Explorer vehicles may exhibit a buzz/vibration/rattle from the center left of the IP during tip-in when the vehicle is up to operating temperature. This may be due to heater tube movement against the tube bracket.
• 10233695Mar 8, 2023Transmission and drivetrain. Some 2017-2023 Ford and Lincoln vehicles equipped with a 10R60/10R80/10R80 MHT/10R100 transmission may exhibit a whine noise at idle and/or while driving. This may be identified as coming from the bellhousing and the front of the transmission fluid pan. The whine noise may become louder when the transmission is at operating temperature and may increase with engine revolutions per minute (RPM) in the park (P)…
• 10233849Mar 1, 2023Engine cooling. Certain 2023 Model Year Explorer, Bronco, Ranger Vehicles Equipped with 2.3L Gas Engine In all of the affected vehicles, a damaged tool used during the engine block machining process may have allowed the main oil galley to exceed specification, resulting in an insufficient seal of the main oil galley plug. An insufficient seal at the main oil galley plug may result in an oil leak from the engine block.
• 10232481Feb 23, 2023Electrical system. Some 2020-2023 Explorer/Aviator vehicles may exhibit the A/C blowing warm air with DTCs P0645, P2CFC, and/or P2CFD present in the heating ventilation and air conditioning (HVAC) module. This may be due to spread terminal/terminal pushout in wire harness 14290 and on the corresponding pins to the body control module C (BCMC). Before replacement of the BCMC, disconnect all connectors from the BCMC and check the BCMC…
• 10232586Feb 10, 2023Engine cooling. Certain 2023 Model Year Explorer, Bronco, Ranger Vehicles Equipped with 2.3L Gas Engine In all of the affected vehicles, a damaged fixture used during the engine block machining process may have allowed the dimension of one of the head bolt bore holes to exceed specification, reducing head bolt thread engagement.
• 10232394Feb 1, 2023Engine cooling. Some 2022-2023 Explorer vehicles equipped with a 2.3L engine may exhibit an intermittent check engine light on with diagnostic trouble code (DTC) P1026 and/or P1299 present in the powertrain control module (PCM) and an engine over-temperature message displayed on the instrument panel cluster (IPC) after a cold start in cold (at or below freezing) ambient temperatures. The vehicle may also enter fail safe cooling…
• 10230835Jan 19, 2023Electrical system. Some 2018-2023 F-150, Expedition, Navigator, Transit, Aviator and Explorer vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0627, P025A, P025B, P00C6, P008A and/or U0109 stored in the powertrain control module (PCM). This may be due to an intermittent or partial disconnect of the harness to the fuel pump control module (FPCM) connector, connector pin push-outs, damaged pins/terminals…
• 10230800Jan 13, 2023Transmission and drivetrain. Some 2020-2023 Explorer/Aviator/Police Interceptor Utility vehicles equipped with a hybrid powertrain may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P2D40. This may be due to the high voltage battery thermal system not cooling as it should. Follow the updated WSM Section 414-03 including listed possible sources, visual inspection and prechecks, and diagnostic…
• 10228881Dec 20, 2022Equipment, Visibility (wipers, defrost, mirrors). Some vehicles equipped with power folding mirrors may exhibit power folding mirrors that are inoperative or exhibit a clicking sound. This may be due to the mirrors being manually folded in, during transportation, going through a car wash, bumped in a parking lot, or found during pre-delivery inspection (PDI). Prior to the replacement of any components, attempt to synchronize the mirrors by following the Power…
• 10228876Dec 16, 2022Brakes. Some Ford and Lincoln vehicles may exhibit noise when the brakes are applied. When diagnosing and repairing brake noise conditions, use the Workshop Manual (WSM) and the appropriate pinpoint test in section 206-00. The brake rotors should only be machined if directed by the WSM because one or more of the following conditions are present on the braking surface: scoring, excessive corrosion/rust or pitting…

← All problems reported for the 2023 Ford Explorer