2015 Ford Mustang Technical Service Bulletins

145 technical service bulletins (TSBs) are on record for the 2015 Ford Mustang. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10164497Aug 7, 2019Electrical system. For Ford and Lincoln vehicles that require positive or negative battery terminal replacement, it is not necessary to replace the complete battery cable harness (14300 and 14301) for this concern. Positive battery cable clamp BT4Z-14450-AA and negative battery cable clamp BT4Z-14450-BA are available for this type of repair. Do not cut or shorten the battery cable, instead carefully remove the affected battery cable…
• 10163593Jul 29, 2019Electrical system. Some 2015-2019 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the appropriate Ford diagnostic scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the body control module (BCM) is internally damaged and requires replacement. The BCM should only…
• 10162086Jun 20, 2019Equipment, Forward collision avoidance. Some 2015-2017 F-150/Mustang, 2015-2018 Edge/MKC, 2016-2018 MKX, 2013-2018 Explorer/Taurus/Flex/MKT, and 2017-2018 Fusion/MKZ/Continental vehicles built on or before 19-Oct-2017 may exhibit an inoperative adaptive cruise control, collision warning, and/or collision avoidance system with a Pre-Collision Assist Not Available, Collision Warning Not Available, and/or Adaptive Cruise Fault message present in the…
• 10162060Jun 11, 2019Vehicle speed control, Transmission and drivetrain. Some 2015-2019 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has come loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition…
• 10160933May 20, 2019Transmission and drivetrain. Some 2015-2019 Mustangs may exhibit a driveline vibration after removal and installation of the drive pinion flange. This may be due to improper removal and installation of the drive pinion flange. It is critical to reinstall the drive pinion flange in the same orientation on the drive pinion stem as it was before it was removed.
• 10160884May 13, 2019Tires. Some 2015-2019 Mustang GT/GT350/GT350R Coupe vehicles equipped with Michelin Pilot Sport Cup 2 tires may exhibit tires which appear to have worn treads even when the tires are new or have low miles. This may be due to the fact that these tires come from the factory with a tread design which has shallower tread depth than most tires. There are also fewer grooves molded into the surface of the tire, with some areas…
• 10160931May 10, 2019Transmission and drivetrain. On vehicles equipped with an automatic transmission it is imperative that the converter pilot hub be greased with Motorcraft Multi-Purpose Grease Spray XL-5-A even if grease was not applied from the factory. Also verify that the engine/transmission alignment dowel pins are present as well as the engine crankshaft dowel pin, if equipped, when installing the transmission. Failure to adequately lubricate the converter…
• 10160880May 6, 2019Equipment. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S.
• 10159494Apr 26, 2019Engine. SSM 47948 - 2010-2019 Various Vehicles - Turbocharged Engines - Oil Supply Filter Replacement When Replacing The Turbocharger Or The Turbocharger Oil Supply Tube For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts.
• 10159489Apr 26, 2019Equipment, Electrical system. Some 2013-2019 vehicles equipped with a EVDC air conditioning (A/C) compressor may exhibit poor A/C performance/improper climate function and/or a diagnostic trouble code (DTC) P06A0 in the powertrain control module (PCM). To support the proper diagnosis of this compressor, the EVDC control valve tester has been developed and is available from Rotunda (339-EVDC100). A tester has been provided to each U.S.
• 10156524Mar 25, 2019Transmission and drivetrain. Some 2015-2019 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the…
• 10156561Mar 5, 2019Seats. Some 2015-2019 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track…
• 10156887Feb 22, 2019Electrical system. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement.
• 10155575Feb 22, 2019Electrical system. Some 2015-2017 vehicles may experience a no crank concern due to a security access key table error. When attempting to program keys or perform a parameter reset, the procedure may fail and the Integrated Diagnostic System (IDS) scan tool may display an error 232: Key Table Not Allocated. If this error message is encountered, the Body Control Module (BCM) is internally faulted and requires replacement.
• 10156863Feb 7, 2019Equipment, Body and structure. Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
• 10155551Feb 7, 2019Body and structure. Some 2000 and newer Ford, Lincoln and Mercury vehicles equipped with aluminum body panels may exhibit corrosion concerns appearing as bubbled and/or peeling paint with or without accompanying white dust. Panel replacement is recommended. Follow the Service Procedure steps to correct the condition
• 10153969Jan 17, 2019Equipment. Some 2012-2019 Vehicles may require repairs to the Smartlink system. Smartlink is a Ford Licensed Accessory which has a warranty provided by the accessory manufacturer. Warranty replacement parts for Smartlink that are ordered through Ford are not reimbursable through the Ford Motor Company warranty system. Please see the Warranty and Policy Manual for further information on Ford Licensed Accessories.
• 10153932Dec 18, 2018Equipment, Electrical system. Some 2015-2017 Mustang vehicles may experience an inoperative rear parking aid camera, luggage compartment lamp, luggage compartment lid release and/or poor satellite radio reception. This may be due to damage to the 14A005 harness in the area of the right side luggage compartment lid hinge. This concern may be accompanied by diagnostic trouble codes (DTCs) B115E, C1001, and B1A89. Follow the Service Procedure…
• 10153931Dec 4, 2018Seats, Equipment. Some 2013-2018 C-Max, 2013-2019 Escape/Fusion/MKZ, 2015-2018 Focus, 2015-2019 Edge/F150/MKC/Mustang, 2016-2018 MKX, 2016-2019 Explorer, 2017 Super Duty, 2018-2019 EcoSport/Expedition, and 2019 Nautilus vehicles may experience seat pan looseness, lateral movement, or clunk/thump noise on turns. Follow the Service Procedure steps to correct the condition.
• 10152473Nov 14, 2018Engine cooling. For 2010-2019 vehicles equipped with turbocharged engines, when diagnosing and/or replacing turbo related concerns, all steps within the Workshop Manual (WSM) procedure must be followed including replacement of all mandatory discarded parts. For all turbocharged engine applications, the turbocharger oil supply filter (6C683 gas engine/6L625 connector style or 6A968 diesel engine) must be replaced whenever the…
• 10152464Nov 1, 2018Electrical system. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic…
• 10148712Oct 24, 2018Transmission and drivetrain. Some 2015-2017 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no DTCs present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. Follow the Service Procedure steps to correct the…
• 10149752Sep 24, 2018Electrical system. Some 2015-2017 Mustang GT350/GT350R vehicles built before 30-Jun-2017 may exhibit an Exhaust Mode Selection Not Available or Drive Mode Not Available message displayed in the instrument panel cluster (IPC) when attempting to change the exhaust mode or drive mode. This may be due to an exhaust tailpipe valve that has frozen in place when the vehicle was started or driven in temperatures at or below freezing. Follow…
• 10149762Sep 17, 2018Brakes. Some 2015-2018 Shelby GT350 and GT350R vehicles may require brake service or repairs to be performed. The vehicles should not have the brake rotors machined when servicing the brake system. Replacement of brake rotors is the only acceptable service of brake rotors on GT350 and GT350R vehicles. GT350 and GT350R vehicles are equipped with a brake system designed for high speed and superior fade resistance. Occasional…
• 10144947Aug 24, 2018Steering. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic…
• 10144920Aug 22, 2018Equipment. Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
• 10144221Jul 26, 2018Equipment, Engine cooling. Some 2015-2017 Mustang vehicles equipped with a 5.0L engine may exhibit an illuminated MIL with diagnostic trouble code (DTC) P0300 through P0308 present. A noticeable misfire may or may not accompany these DTCs. If normal diagnostics do not lead to a root cause for this concern, remove the intake manifold from the vehicle and verify the intake manifold runner control (IMRC) plates move when the IMRC actuators are…
• 10144218Jul 20, 2018Equipment, Electrical system. Some 2015 and 2016 Mustang vehicles built on or before 4/22/2016 may exhibit a partial outage of the rear tail, turn signal or stop lamps following a vehicle start with a low battery. This may be accompanied by any combination of DTCs B1271, B1272, B1273, B1274, B1275 and B1276. The condition typically clears on vehicle restart. Reprogram the BCMB module to the latest calibration using IDS release 110.01 or higher…
• 10143098Jun 20, 2018Equipment, Engine cooling. Some 2015-2018 Mustang GT350s may exhibit an engine oil leak that appears to be originating from the oil filter adapter or oil cooler. If the leak appears to be originating from the oil cooler, be aware that the leak may actually be originating from the oil filter adapter, and oil may run down the oil cooler tubes and drip off of the cooler, making it appear that the leak is originating from the oil cooler.
• 10143077Jun 8, 2018Equipment. Some 2015-2017 Mustang vehicles may exhibit poor A/C performance. If the cause of this is found to be a refrigerant leak from the evaporator, it is recommended to replace only the evaporator as opposed to the entire climate control housing. Follow the Service Procedure steps to correct the condition.
• 10137128Apr 10, 2018Equipment. Some 2015-2018 Mustang vehicles equipped with SYNC 3 may exhibit inoperative USB ports with the diagnostic trouble code (DTC) B1252:13 stored in the accessory protocol interface module (APIM.) This may be due to a loose connection or damage present on the cable which connects the APIM to the media hub. Follow normal Workshop Manual (WSM) diagnosis to correct this condition, while paying close attention to any…
• 10137113Mar 30, 2018Equipment. Replacing the original equipment SYNC/Navigation system with either an aftermarket SYNC/Navigation kit or modifying original SYNC/Navigation parts to provide additional features is not recommended nor supported on any Ford, Mercury or Lincoln vehicle. Only approved Genuine Ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems.
• 10137112Mar 30, 2018Seats. Some 2015-2018 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track…
• 10137079Mar 30, 2018Body and structure. Some 2015-2018 Mustang GT350 vehicles built on or before 26-Feb-2018 may exhibit an excessive panel gap where the rear bumper cover meets the rear quarter panels on either side of the vehicle. This may be due to the method used to fasten the rear bumper cover to the vehicle. Follow the Service Procedure steps to correct the condition.
• 10137091Mar 13, 2018Equipment. Some 2015-2017 Mustang vehicles built on or before 2-Sep-2016 may exhibit poor A/C performance. If a low refrigerant charge is confirmed and there are no other obvious signs of a refrigerant leak, suspect the evaporator to be the source of the leak.
• 10136597Feb 14, 2018Equipment. 2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
• 10136592Feb 9, 2018Electrical system. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic…
• 10136574Feb 7, 2018Body and structure, Equipment. Some 2015-2018 Mustang vehicles with a convertible top may exhibit a condition where the top sags on one or both sides near the rear glass due to broken tension rod clips. Follow the Service Procedure steps to correct the condition.
• 10140324Jan 11, 2018Equipment. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal.
• 10138525Jan 11, 2018Equipment. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal.
• 10140311Jan 3, 2018Body and structure, Equipment. Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position.
• 10138512Jan 3, 2018Visibility (wipers, defrost, mirrors). Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position.
• 10127405Nov 2, 2017Electrical system, Transmission and drivetrain. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the…
• 10109017Apr 13, 2017Engine cooling. Some 2015 - 2017 Mustang vehicles may experience exhaust alignment issues. Before replacement of exhaust system components for this issue, align the exhaust system following the workshop manual (WSM) procedure found in section 309-00, Muffler and Tailpipe removal and installation. The WSM procedure has been revised with updated steps to resolve these issues.
• 10100524Mar 20, 2017Equipment. Certain 2015 through 2017 model year mustang shelby® gt350 and gt350r vehicles - complimentary oil filter wrench.
• 10099463Mar 14, 2017Transmission and drivetrain. 2009-2017 vehicles equipped with a 6r80, 6r100, 6r140 automatic transmission have an updated main control valve body overhaul procedure. Refer to workshop manual (wsm), section 307-01 for main control valve body (7a100) overhaul procedures. Not all valve bodies require replacement. Inspect the valve body bores, springs and valves as directed during diagnosis and repair.
• 10095224Jan 27, 2017Equipment. Some 2015 edge,mustang and f150 vehicles with a 4" display may exhibit a 24 hour clock display that resets itself to a 12 hour display after cycling the ignition key. To correct the concern, reflash the front control display interface module (fcdim) to the latest calibration using ids version 103.05 or higher. Make sure you are connected to the internet when entering module programming to obtain the latest updates…
• 10095184Jan 24, 2017Equipment. Replacing the original equipment sync/navigation system with either an aftermarket sync/navigation kit or modifying original sync/navigation parts to provide additional features is not recommended nor supported on any ford, mercury or lincoln vehicle. Only approved genuine ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems.
• 10095154Jan 10, 2017Engine. To help differentiate engine oil leaks from other possible sources, a new white-colored fluorescent engine oil dye is available. Workshop manual (wsm), section 303-00 has been revised to reference the new white-colored dye. The new white fluorescent dye provides a distinct white glow to identify engine oil leaks. The new white fluorescent dye requires a pure uv diagnostic inspection lamp. The white-colored…
• 10094612Dec 9, 2016Engine. Some 2015-2016 edge with 2.0l gasoline turbocharged direct injection (gtdi), 2015-2016 mustang and f-150 with 5.0l engine and 2016 explorer equipped with 2.3l gtdi engine may exhibit oil leak at engine oil pressure (eop) sensor threads. It is not required to replace the sensor if it is leaking from the threads. Remove and reseal the eop sensor, refer to workshop manual (wsm), sections 303-14. Check the oil level…

← All problems reported for the 2015 Ford Mustang