2017 Ford Mustang Technical Service Bulletins

155 technical service bulletins (TSBs) are on record for the 2017 Ford Mustang. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10137112Mar 30, 2018Seats. Some 2015-2018 Mustang vehicles may exhibit a concern of no horizontal movement of the front power seats. This may be caused by a defective seat track motor or separation of the drive motor cable from the seat track. The seat track motor assembly is available separately (14547) and replacement of the complete seat frame assembly (9661711) may not be required. Refer to Workshop Manual, Section 501-10A for seat track…
• 10137079Mar 30, 2018Body and structure. Some 2015-2018 Mustang GT350 vehicles built on or before 26-Feb-2018 may exhibit an excessive panel gap where the rear bumper cover meets the rear quarter panels on either side of the vehicle. This may be due to the method used to fasten the rear bumper cover to the vehicle. Follow the Service Procedure steps to correct the condition.
• 10137102Mar 21, 2018Equipment. Some 2016-2018 Ford and Lincoln vehicles equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit functional concerns where USB audio playback and App Link will not operate. This may also include, under certain conditions, no Bluetooth streaming. Apple has released iOS 11.2.6 to address this concern. Advise the customer to update the device to iOS 11.2.6 and re-evaluate before…
• 10137101Mar 21, 2018Transmission and drivetrain. Some vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. This may be due to small debris causing the VCT solenoid to stick. Before attempting any component diagnosis or replacement of the VCT solenoid, refer to Powertrain Control and Emissions Diagnosis (PC/ED) pinpoint test HK11 to cycle the affected…
• 10137100Mar 19, 2018Electrical system. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then…
• 10137091Mar 13, 2018Equipment. Some 2015-2017 Mustang vehicles built on or before 2-Sep-2016 may exhibit poor A/C performance. If a low refrigerant charge is confirmed and there are no other obvious signs of a refrigerant leak, suspect the evaporator to be the source of the leak.
• 10136611Feb 21, 2018Equipment. Some 2016-2018 Ford and Lincoln Vehicle equipped with SYNC 3 and connected to an iPhone recently upgraded to iOS 11.2.5 may exhibit a concern where USB Audio playback and App Link applications will not function properly. This may also include, under certain conditions, no Bluetooth Streaming. Apple is aware of the issue and is working on a resolution with a future iOS release. No repairs should be performed at this…
• 10136597Feb 14, 2018Equipment. 2010-2018 various vehicles equipped with SYNC or SYNC 3 may not function when attempting to find or use the Spotify app via AppLink. As of an update released on 1/15/2018 Spotify will no longer be supporting their AppLink integration. No repair attempts should be attempted to correct this concern.
• 10136592Feb 9, 2018Electrical system. When connecting the Vehicle Communication Module (VCM) and Integrated Diagnostic System (IDS) or Ford Diagnosis and Repair System (FDRS) to the DLC located on the driver side under the steering column at the GWM, make sure that the ignition is off before connecting the VCM. If the ignition is on or the engine is running during the connection, it can result in various warning lights being illuminated with diagnostic…
• 10136574Feb 7, 2018Body and structure, Equipment. Some 2015-2018 Mustang vehicles with a convertible top may exhibit a condition where the top sags on one or both sides near the rear glass due to broken tension rod clips. Follow the Service Procedure steps to correct the condition.
• 10140332Jan 29, 2018Equipment, Electrical system. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then…
• 10138533Jan 29, 2018Equipment. Various 2016-2017 vehicles with SYNC 3 may experience a touch screen that does not respond to any input. Using the Professional Technician Society (PTS) website > OASIS tab > SYNC version, verify the vehicle SYNC software version. If the vehicle is at version 2.2 please update the module to the latest software level. After the software is updated make sure you shut the vehicle off, open the door for 2 minutes, then…
• 10140324Jan 11, 2018Equipment. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal.
• 10138525Jan 11, 2018Equipment. Some 2015-2018 F-150, Mustang and Transit vehicles built on or before 01-Dec-2017 may have a concern of no airflow from the climate control vents. This may be caused by a seized or sticking A/C clutch. This can be repaired by replacing only the A/C clutch (19D786/19D784). The compressor assembly (19703) may not be required. Refer to Workshop Manual, Section 412-00 for A/C clutch removal.
• 10140284Jan 10, 2018Equipment, Electrical system. Some 2017 Mustangs equipped with DATC may exhibit poor A/C performance. This may be due to the way in which the front controls interface module (FCIM) software regulates the interior temperature. Follow the Service Procedure steps to correct the condition.
• 10138485Jan 10, 2018Equipment. Some 2017 Mustangs equipped with DATC may exhibit poor A/C performance. This may be due to the way in which the front controls interface module (FCIM) software regulates the interior temperature. Follow the Service Procedure steps to correct the condition.
• 10140311Jan 3, 2018Equipment, Body and structure. Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position.
• 10138512Jan 3, 2018Visibility (wipers, defrost, mirrors). Some 2015-2017 Mustang Convertibles built on or before 1-Feb-2017 may exhibit wear marks or damage to the exterior surface of the convertible top in the area of the front outer edges. This may be due to contact between the convertible top and the tonneau covers that may be installed on the vehicle by the customer when the top is in the open position.
• 10127426Nov 29, 2017Equipment, Electrical system. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. SYNC software updates are now available under the OASIS Tab SYNC selection. If update is available, refer to WSM Section 415-00 and update APIM software. For claiming, use causal part 14G371 and applicable labor operations in section 10 of the SLTS manual.
• 10127425Nov 29, 2017Electrical system, Equipment. Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC software updates are now available under the OASIS Tab SYNC selection. If an update is available…
• 10127424Nov 29, 2017Equipment, Back-over prevention (rear camera), Electrical system, Lane departure. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse. SYNC software updates…
• 10127417Nov 22, 2017Equipment. Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale.
• 10127405Nov 2, 2017Transmission and drivetrain, Electrical system. Some vehicles may exhibit a no start condition with an illuminated malfunction indicator lamp (MIL) and a DTC P161A after PCM replacement. This may be due to the parameter reset procedure not being properly completed. To clear this DTC, use the Ford Integrated Diagnostic System (IDS) service tool or Ford J2534 Diagnostic Software, select - Toolbox - Body - Security - PATS Functions - Parameter Reset. Follow the…
• 10125079Oct 6, 2017Equipment. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may intermittently display an overhead image of a vehicle in the center of the SYNC touchscreen with no obstacle detection grids or warning chimes. SYNC may appear unresponsive when the overhead vehicle image is displayed. The vehicle image may intermittently display after shifting out of reverse or turning the vehicle off when in reverse.
• 10125078Oct 6, 2017Equipment. Some 2016-2018 Ford or Lincoln vehicles equipped with SYNC 3 may exhibit a blank screen or other various SYNC symptoms only when the vehicle is in transport mode. This is due to the power saving features enabled while in transport mode and is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale.
• 10119684Sep 28, 2017Electrical system. Some owners of 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 may experience inoperative mobile device navigation applications. Mobile device navigation via AppLink requires SYNC 3 version 2.3 or higher for Apple iOS users. Mobile device navigation via AppLink is not currently available for Android users. SYNC 3 software upgrades to support these apps are not currently available, do not attempt any…
• 10119678Sep 21, 2017Electrical system. Some 2016-2017 Ford and Lincoln vehicles with SYNC 3 may exhibit an intermittent blue or black screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. After Installation Complete pop-up appears, remove USB flash drive and install into IDS tool to update Ford database. Perform a complete ignition cycle by turning the key…
• 10119671Sep 13, 2017Engine. 2017 vehicles equipped with a 2.0L GTDI, 2.3L GTDI, or 2.5L PFI engine will either be equipped with a diamond washer on each side of a smooth-faced crankshaft timing sprocket (early build), or a crankshaft timing sprocket with laser etched faces and no diamond washers (late build). If equipped, diamond washers should be cleaned, inspected and reused, if undamaged. Diamond washers should never be installed along…
• 10119669Sep 13, 2017Electrical system. Some 2016-2017 Ford and Lincoln vehicles equipped with SYNC 3 version 2.2 software may exhibit a blank screen after attempting to exit Valet mode. To recover the screen, perform a complete ignition cycle (key off, open and close the driver's door then wait 5 minutes). The SYNC software version of the vehicle can be confirmed via OASIS. Do not attempt any repairs at this time. Engineering is investigating; Monitor…
• 10115952Jul 14, 2017Electrical system. Some 2016-2017 Ford/Lincoln vehicles SYNC 3 may exhibit an intermittent blank screen. Check for SYNC software update under the OASIS Tab SYNC selection. If update is available refer to WSM, Section 415-00 and update APIM software. During the update process the SYNC status bar shows Updating System Software for approximately 30 minutes. After Installation Complete pop-up appears, remove USB flash drive and install…
• 10109001Apr 18, 2017Back-over prevention (rear camera), Equipment. Some 2016-2017 Edge, Escape, Expedition, Fiesta, Flex, MKC, MKT, MKX, Mustang, Navigator and Taurus or 2017 Explorer and Super Duty vehicles equipped with SYNC 3 and built on 1-Jul-2015 and through 31-Dec-2016 may exhibit a SYNC display message of Please check your surroundings for safety along with no rear view camera image when in reverse gear. This will occur only at ambient temperatures ranging from -5 Å'C to 5…
• 10109017Apr 13, 2017Engine cooling. Some 2015 - 2017 Mustang vehicles may experience exhaust alignment issues. Before replacement of exhaust system components for this issue, align the exhaust system following the workshop manual (WSM) procedure found in section 309-00, Muffler and Tailpipe removal and installation. The WSM procedure has been revised with updated steps to resolve these issues.
• 10100508Mar 23, 2017Electrical system. Some 2016-2017 ford or lincoln vehicles equipped with sync 3 may exhibit a blank screen or other various sync symptoms only when the vehicle is in transport mode. This is considered normal due to the power saving features enabled while in transport mode. It is beneficial for battery life to keep the vehicle in transport mode until the vehicle is prepped for sale.
• 10100524Mar 20, 2017Equipment. Certain 2015 through 2017 model year mustang shelby® gt350 and gt350r vehicles - complimentary oil filter wrench.
• 10099463Mar 14, 2017Transmission and drivetrain. 2009-2017 vehicles equipped with a 6r80, 6r100, 6r140 automatic transmission have an updated main control valve body overhaul procedure. Refer to workshop manual (wsm), section 307-01 for main control valve body (7a100) overhaul procedures. Not all valve bodies require replacement. Inspect the valve body bores, springs and valves as directed during diagnosis and repair.
• 10099458Mar 14, 2017Equipment. Some vehicles may exhibit an illuminated mil with diagnostic trouble codes (dtcs) p0011, p0012, p0014, p0015, p0016, p0017, p0018, p0019, p0021, p0022, p0024 and/or p0025. This may be due to small debris causing the vct solenoid to stick. Before attempting any component diagnosis or replacement of the vct solenoid, refer to powertrain control and emissions diagnosis (pc/ed) pinpoint test hk11 to cycle the affected…
• 10095621Feb 24, 2017Engine. Some 2017 mustang vehicles equipped with a 2.3l engine and built on or before 13-jan-2017 may exhibit an illuminated mil with dtcs p0456, p1450 and/or p144c. Follow the service procedure steps to correct the condition.
• 10095184Jan 24, 2017Equipment. Replacing the original equipment sync/navigation system with either an aftermarket sync/navigation kit or modifying original sync/navigation parts to provide additional features is not recommended nor supported on any ford, mercury or lincoln vehicle. Only approved genuine ford accessories or originally installed systems are supported and certified to function correctly with other vehicle systems.
• 10095154Jan 10, 2017Engine. To help differentiate engine oil leaks from other possible sources, a new white-colored fluorescent engine oil dye is available. Workshop manual (wsm), section 303-00 has been revised to reference the new white-colored dye. The new white fluorescent dye provides a distinct white glow to identify engine oil leaks. The new white fluorescent dye requires a pure uv diagnostic inspection lamp. The white-colored…
• 10095976Nov 2, 2016Body and structure. 2015 - 2017 shelby gt350 and gt350r vehicles require installation of the 3 piece front splitter on gt350 and 1 piece front splitter on the gt350r models during pre-delivery inspection (pdi). Installation instructions can be found on the professional technician society (pts) website under the pdi tab for each of the models. There is also a link within the instructions for each of the vehicles to a video depicting…
• 10095975Nov 2, 2016Engine. Some 2016-2017 mustang gt350 equipped with the 5.2l engine may exhibit a rattle or rapping type sound during cold operation at light loads and speeds from idle - 3000 rpm. The noise will be most noticeable during light acceleration in the 1500-3000 rpm range and may also be noticeable in the 800-1200 rpm range with neutral throttle blips. This sound is caused by the piston motion in the cylinder bore.
• 10091003Oct 26, 2016Tires. Setting the correct tire inflation pressure is an important step in the pre-delivery process and during routine maintenance intervals. Recent customer clinics revealed that most every vehicle in the clinics had the tire pressures set incorrectly. Tire pressures from the factory are not set to the correct specification. Maintaining the correct tire pressure is key to the ride characteristics of the vehicle and…
• 10091151Oct 17, 2016Brakes. Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service is required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps…
• 10090681Oct 17, 2016Brakes. Some 2008-2017 ford/mercury/lincoln vehicles equipped with sync may generate a vhr that identifies a concern with the brakes and suspension category indicating service is required due to a brake system warning lamp being illuminated. If the park brake was applied when the vhr was gathering data from the major vehicle systems, the brakes and suspension message will be reported as the vhr looks for any warning lamps…
• 10090662Oct 10, 2016Steering. When hooking up the vehicle communication module (vcm) and integrated diagnostic system (ids) to the dlc located on the driver side under the steering column at the gwm, make sure that the ignition is off before connecting to ids. If the ignition is on or the engine is running during the hook up, it can result in various warning lights being illuminated with diagnostic trouble codes (dtcs), no start or no crank…
• 10109079Sep 30, 2016Seat belts. Some vehicles may have a concern where the safety belt retractor webbing does not extract from the stowed position or exhibits excessive pressure on the occupant during use. This may be due to a normal condition which happens when the seatbelt retracts at a high rate of speed. The Workshop Manual, Section 501-20A General Procedures has been updated with a locked seatbelt retractor releasing procedure.
• 10109070Sep 21, 2016Engine cooling, Engine. The Powertrain Control/Emissions Diagnosis (PC/ED) manual has been revised for diagnosing electronic throttle bodies (ETBs). The ETC_ACT and ETC_DSD PIDs should not used to diagnose possible ETB concerns. The IDS has a limited refresh rate when reading these PIDs and cannot display quickly enough to validate a concern. The PCM automatically monitors these inputs more accurately and will set diagnostic trouble codes…
• 10109067Sep 19, 2016Electrical system, Equipment. Some 2016-2017 Escape, MKC, Fiesta, F150, Expedition, Navigator, Mustang, Transit, Focus, C-Max, MKX, Taurus, MKS, Flex, MKT, and Edge and 2017 Explorer, Fusion, MKZ, Super Duty, Transit Connect and Continental vehicles equipped with SYNC 3 might exhibit a blank screen or other various SYNC symptoms only when the vehicle is in Transport mode. Engineering is aware of this possibility and it is considered normal due…
• 10092573Aug 26, 2016Engine, Engine cooling. Some 2016 - 2017 mustang shelby gt350 vehicle may exhibit a p26fe dtc with diagnostics leading to replacement of the exhaust tailpipe actuator. This part was not initially released for service. This part is now available for service and workshop manual procedures are now available in section 309-00d. The service part no. Is fr3z-5k245-a.
• 10092562Aug 22, 2016Steering, Electrical system. When hooking up the vehicle communication module (vcm) and integrated diagnostic system (ids) to the dlc located on the driver side under the steering column at the gwm, make sure that the ignition is off before connecting to ids. If the ignition is on or the engine is running during the hook up, it can result in various warning lights being illuminated with diagnostic trouble codes (dtcs), no start or no crank…

← All problems reported for the 2017 Ford Mustang