2013 Infiniti G37 Technical Service Bulletins

125 technical service bulletins (TSBs) are on record for the 2013 Infiniti G37. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192433Sep 3, 2014Brakes. IF YOU CONFIRM: The rear brakes squeak when braking while the brakes are at normal operating temperature AND the applied vehicle is equipped with single piston rear brake calipers. ACTION: Replace the hardware on both rear brake calipers with the kit listed in PARTS INFORMATION in this bulletin. NOTE: Machining of the rotors is not necessary. Refer to the Electronic Service Manual (ESM), section BR-Brake System…
• 10192401Jul 7, 2014Body and structure, Electrical system. SERVICE INFORMATION If the battery becomes disconnected or discharged while the retractable hard top is in any position other than fully closed or fully retracted, the retractable hard top control may stop operating and the following DTCs will be stored: B1707 and B1708. Other retractable hard top related DTCs may also be found stored. To restore operation: (1) close the roof fully manually; (2) erase the DTC(s)…
• 10192396Jun 24, 2014Equipment, Electrical system. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10192357Apr 30, 2014Equipment, Body and structure. SERVICE INFORMATION If the hydraulic unit assembly (pump assembly) needs to be tested for any reason, the convertible top should not sink or drop further than 250 mm (9.84 inches) within one (1) minute or less when opened as shown in Figure 1. - If the convertible top sinks further than 250 mm (9.84 inches) within one (1) minute or less - the pump assembly needs to be replaced.
• 10192355Apr 29, 2014Electrical system, Equipment. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Infiniti vehicles has changed. This bulletin gives an outline of the retailer technician?s responsibilities in assisting the retailer claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
• 10192345Apr 7, 2014Transmission and drivetrain, Steering. SERVICE INFORMATION When diagnosing an applied vehicle for possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, in some cases it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. - Go to Power Steering Gear Inspection starting on page 2. See this bulletin for further detail.
• 10192323Feb 13, 2014Engine cooling. IF YOU CONFIRM: The MIL is ON and one or both of the following DTCs are found stored in the ECM: - P0139 (heated oxygen sensor 2 (B1) circuit slow response) - P0159 (heated oxygen sensor 2 (B2) circuit slow response) ACTION: 1. Confirm this bulletin applies. - Compare the vehicle's current ECM part number to those listed in Table A (see page 4). 2. If the ECM part number does not match one listed in Table A, this…
• 10192314Jan 27, 2014Electrical system, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192294Jan 13, 2014Engine cooling, Engine. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Infiniti vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
• 10192235Aug 27, 2013Equipment, Wheels. Infiniti Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Infiniti design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Infiniti's standards.
• 10192232Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulletin for further details.
• 10192224Jul 26, 2013Electrical system, Visibility (wipers, defrost, mirrors). SERVICE INFORMATION When the headlamp switch is set to the AUTO position, AND the fog lamp switch is turned ON, ... the fog lamps and headlamps are designed to come on, regardless of ambient lighting. If the customer would prefer that both the headlamps and fog lamps not come on during daylight conditions while in AUTO mode, perform the steps in this bulletin to disable the fog lamp override feature. See this…
• 10192221Jul 25, 2013Fuel system. SERVICE INFORMATION Part order approval from TECH LINE is no longer required when replacing the Audio Visual (A/V) Control Unit on an Applied Vehicle. Previously, TECH LINE would need to be contacted to confirm (or assist with) diagnosis and the proper repair prior to ordering an A/V control unit. This process has been suspended.
• 10192220Jul 25, 2013Vehicle speed control, Air bags, Equipment. SERVICE INFORMATION: If the BCM in an Applied Vehicle is replaced for any reason and not configured correctly, the following issue may occur - When the driver door is opened, the convertible top opens.
• 10192219Jul 23, 2013Steering, Suspension, Brakes. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake issues fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192218Jul 23, 2013Brakes, Wheels, Steering. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192201Jun 27, 2013Electrical system, Transmission and drivetrain. SERVICE INFORMATION - The Applied Vehicles listed in this bulletin may arrive at the dealer with a "Power Cut OFF Switch" (see Figure 1). - This Power Cut Off Switch should have been removed before the vehicle was shipped to the dealer. In a few cases, a vehicle may arrive at the dealer with the switch still installed. - If a vehicle arrives at the dealer with a Power Cut Off Switch installed, it must be removed…
• 10192191Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10192182May 21, 2013Back-over prevention (rear camera). IF YOU CONFIRM: The MIL is on with DTC P0710 (Transmission Fluid Temperature Sensor A) stored in the ECM only. NOTE: The DTC P0710 will only set in the ECM. If the DTC is set in both the ECM and TCM, this TSB does not apply. Refer to ASIST and the ESM for further diagnosis for DTC P0710. ACTION: Confirm this bulletin applies. * Check and compare your Current TCM Part Number to Table A on page 4. Please see this…
• 10192161Apr 4, 2013Electrical system. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
• 10192157Apr 3, 2013Seat belts, Vehicle speed control. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled…
• 10192149Mar 22, 2013Wheels, Back-over prevention (rear camera), Transmission and drivetrain…. IF YOU CONFIRM: Customers concern of a "clicking" noise coming from either left or right front/rear axles during take-off/acceleration. ACTION: Apply Molykote M77 grease (P/N 44003-7S000) to the hub bearing surfaces. NOTE: * Do not remove the axle from the hub or transmission for this bulletin * Refer to the Electronic Service Manual (ESM) for model specific torque specifications. >Please see Service procedure for…
• 10192146Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192126Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192101Dec 21, 2012Wheels. SERVICE INFORMATION To increase tire/wheel assembly balancing accuracy, proper steps should be followed: - Make sure to use the correct size wheel centering collet (do not use a cone). - Make sure to use a flange plate and stud set to secure the tire/wheel assembly on the balancer (do not use a cup). - Perform proper wheel mounting and centering checks. See this bulletin for further detail.

← All problems reported for the 2013 Infiniti G37