2021 Mazda CX-30 Technical Service Bulletins

616 technical service bulletins (TSBs) are on record for the 2021 Mazda CX-30. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10235701Apr 14, 2023Electrical system. Some customers may complain about an intermittent Beep sound (popping sound) every 1-2 minutes while driving. This may be cause by a software error in the navigation SD card.
• 10235696Apr 14, 2023Electrical system. Qi Wireless Charger symptom troubleshooting
• 10235693Apr 13, 2023Fuel system. Some customers will report that their fuel door was stuck closed and would not open to refuel the vehicle. Follow the repair steps below unless the conditions outlined in TSB 09-019/21 - FUEL-FILLER LID PANEL IS DEFORMED for 2019-2021 Mazda3 and 2020-2021 CX-30 are present.
• 10235415Apr 3, 2023Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface.
• 10233683Mar 28, 2023Latches, locks and linkages, Engine cooling, Exterior lighting. Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
• 10233661Mar 22, 2023Seats. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmers fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat…
• 10233669Mar 21, 2023Equipment. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method
• 10233569Mar 17, 2023Electrical system, Equipment. Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
• 10233674Mar 10, 2023Equipment. Mazda Connect Services - Frequently Asked Questions (FAQ)
• 10233560Mar 8, 2023Exterior lighting. This document has been superseded by 09-015/23 - ABNORMAL NOISE FROM FRONT COMBINATION LIGHT please refer to the linked document for the latest information. This document will remain active for 60 days, at which point it will be unpublished. Page
• 10233704Mar 1, 2023Visibility (wipers, defrost, mirrors). Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
• 10233562Mar 1, 2023Engine cooling, Exterior lighting, Equipment, Latches, locks and linkages. Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF
• 10232298Feb 24, 2023Exterior lighting. Some customers may notice an abnormal noise (i.e. whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process. The fan motor bearing may become worn out during use. To eliminate the noise, the production process at the supplier and the material has been…
• 10232297Feb 23, 2023Visibility (wipers, defrost, mirrors), Body and structure. Some vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty corrosion, may drip out from gaps under the outer mirror…
• 10232274Feb 16, 2023Engine cooling. Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable.
• 10232285Feb 9, 2023Seats, Other or unknown. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat…
• 10232281Feb 7, 2023Body and structure, Other or unknown, Latches, locks and linkages. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate. To eliminate this concern, the internal structure of the latch and surface treatment of the bolts have been modified.
• 10232303Feb 6, 2023Equipment, Engine cooling, Electrical system, Exterior lighting. Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
• 10232271Feb 3, 2023Engine cooling. Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure. DTC P0524:00 (Engine oil pressure too low), DTC P055F:00 (Engine oil pressure malfunction). The control software of the PCM has been modified to eliminate…
• 10232266Feb 3, 2023Engine cooling. Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P0301:00, P0302:00, P0303:00, P0304:00.NOTE: Only turbo engines are applicable; non-turbo engines are NOT applicable. In most cases, DTCs P030X stores, but sometimes not. Sometimes the CHECK ENGINE light does not recognize this engine concern.
• 10232302Feb 2, 2023Steering, Wheels. Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
• 10232402Feb 1, 2023Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
• 10230891Jan 31, 2023Engine cooling. Some vehicles may have a "LOW ENGINE OIL LEVEL" warning message and an engine oil level warning light on in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the…
• 10230866Jan 25, 2023Electrical system. Due to the supply chain shortages for BDGF-66-5G0G, hardware has been confirmed compatible between BDGF-66-5G0B up to the G suffix. This can be used for repair with vehicles originally equipped with C to G level suffix parts.
• 10230902Jan 23, 2023Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10230880Jan 23, 2023Electrical system. Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect clock and/or tire pressures and/or tire pressure missing. This may be caused by: - Incorrect calendar entry (month/day/year) after a battery disconnect - Infotainment system software update. - BCM TPMS unlearn during vehicle storage or transport. - Wheel/Tire change
• 10230865Jan 23, 2023Engine cooling. When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
• 10230878Jan 19, 2023Electrical system. Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 10230877Jan 13, 2023Latches, locks and linkages. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate.
• 10230875Jan 11, 2023Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10230900Jan 9, 2023Latches, locks and linkages. Some customers may experience that after the doors are locked and the Fuel Door Lock Delay with MAZDA CONNECT has passed (default setting is 90 seconds), the fuel-filler lid does not lock and can be opened when pressing it. NOTE: - The fuel-filler lid does not lock immediately after the doors are locked, but after the time set in the Fuel Door Lock Delay (0, 30, 60, 90, and 120 seconds).
• 10230873Jan 6, 2023Exterior lighting. Some customers may complain about hearing noise from their headlamps. While some noise is normal from the electric motor, if it is louder in one headlamp than the other or both are significantly louder than a known good vehicle
• 10230888Jan 4, 2023Engine cooling. Some customers may complain about a poor acceleration and rough idling or the CHECK ENGINE light ON with DTC P030X:00 (only turbo engines are applicable; non-turbo engines are NOT applicable). - In most cases, P030X is stored, but sometimes not. - Sometimes the CHECK ENGINE light does not recognize this engine concern.
• 10230894Jan 3, 2023Electrical system. Some vehicles may exhibit DTC U3000:04 (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued (only vehicles in which the customer opted out of CV services are affected - CSP04). This is caused by improper control software of telematics communication unit. To eliminate this concern, the control software of telematics communication unit has been modified.
• 10228661Dec 22, 2022Brakes. Some customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate.
• 10228662Dec 21, 2022Visibility (wipers, defrost, mirrors), Electrical system. Some customers may complain the A/C blows warm. This may be caused by one of two things. Cause 1: After accelerating in hot weather, the A/C blows warm air for a longer time than other models. This is caused by improper control software of the PCM not allowing the A/C compressor to resume properly after acceleration. During a hard acceleration above a certain throttle level opening, the PCM stops the A/C compressor…
• 10228657Dec 20, 2022Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10228659Dec 19, 2022Engine cooling. Some vehicles may experience an engine stall when hard accelerating from a stop (often difficult to reproduce on a test drive), no codes are stored and the vehicle easily restarts with no other drivability concerns. This is only caused in certain situations by the torque reduction calibration in the PCM software. To correct this issue, the control software of the PCM has been modified to optimize the torque…
• 10228650Dec 14, 2022Electrical system. Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 10228664Dec 13, 2022Electrical system. Some vehicles may exhibit the following symptoms with DTC P05A0:00 (Active air shutter and the opening angle abnormality (sticking)) stored in memory. Symptom 1 [Mazda3 and CX-30]: The active air shutter is working, but DTC P05A0:00 is stored in memory. Cause 1: This is caused by improper control software of the PCM detecting the DTC immediately without performing the failsafe operation.
• 10228653Dec 13, 2022Electrical system. MAZDA CONNECTED SERVICES Frequently Asked Questions (FAQ)
• 10228652Dec 13, 2022Electrical system. Some customers may complain about any of the following: * Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. * Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF * MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Confirm the customer's phone and vehicle have good to strong…
• 10228651Dec 7, 2022Equipment. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 10228663Dec 1, 2022Body and structure. Some vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty corrosion, may drip out from gaps under the outer mirror…
• 10228648Dec 1, 2022Engine cooling. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10226856Nov 22, 2022Electrical system. Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. - Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. - Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.
• 10226892Nov 21, 2022Electrical system. Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning…
• 10226814Nov 18, 2022Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10226900Nov 16, 2022Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA04_12004 or later). Ver. 7000C0A-NA04_12004 and later fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * When the gear position is shifted into P from R, the screen may not return to the previous condition before shifting…
• 10226889Nov 15, 2022Electrical system, Seats. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs "B1030:13" and/or "B1032:13" are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has…

← All problems reported for the 2021 Mazda CX-30