2013 Mazda CX-5 Technical Service Bulletins

824 technical service bulletins (TSBs) are on record for the 2013 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10143979Jul 3, 2018Equipment. NO GPS AFTER TOMTOM NAVIGATION ACCESSORY INSTALLATION: When not equipped with TomTom navigation from the factory, the GPS antenna plugs into the handsfree (Bluetooth) unit. When adding TomTom navigation, the cable must be unplugged from the HF unit and plugged into the jumper harness that leads to the navi unit.
• 10143965Jun 20, 2018Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following…
• 10143955Jun 6, 2018Engine cooling. IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the…
• 10143961Jun 5, 2018Steering, Suspension. Some customers may complain about a vibration that is felt through the floor, seat and/or steering wheel while driving under moderate acceleration, at speeds of approx. 25 - 30 mph (40 - 50 km/h). The vibration is more noticeable when driving on smooth, flat roads.The vibration may be caused by wear on the inner surface of the tripod joint case (inner side of front driveshaft).
• 10142521May 15, 2018Steering. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of…
• 10142527May 11, 2018Equipment. Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement.
• 10142517May 11, 2018Engine cooling. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
• 10142515May 11, 2018Brakes. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare…
• 10142533May 8, 2018Engine. If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines.
• 10142525May 8, 2018Equipment. When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).
• 10142520May 8, 2018Tires. This service bulletin illustrates the conditions when a TPMS warning light may illuminate, why it illuminated and how to properly initialize the system.The Tire Pressure Monitoring System (TPMS) monitors the tire pressure of all four tires indirectly using the data sent from the ABS wheel speed sensors.
• 10142519May 8, 2018Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road.
• 10142516May 8, 2018Engine. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this…
• 10142518May 7, 2018Tires. Customer complaints have been reported where the TPMS warning light is unnecessarily illuminated because the TPMS initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times…
• 10142531May 3, 2018Body and structure. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10136786Apr 27, 2018Seats. Some vehicles may exhibit inoperative driver and/or front passenger side seat warmer(s) in any mode (High, Mid and Low). This may be caused by repeated load applied to the seat cushion (1) while the seat isoccupied. A section of the heater mat (2) just above the reinforcement rod (3) in the cushion pad contactsinternal heater mat wire and causes damage (4).
• 10136776Apr 27, 2018Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10136774Apr 27, 2018Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10136783Apr 20, 2018Visibility (wipers, defrost, mirrors). Some customers may complain about one or both of the following symptoms: When selecting the "Defroster Vents" position (2) with the Mode Selector Dial (1), the dial does not stay in the "Defroster Vents" position and returns to the "Defroster/Floor Vents" position (3). When rotating the Mode Selector Dial (1) to the "Defroster Vents" position (2), it may be difficult to tell if the Mode Selector Dial is firmly in…
• 10136782Apr 16, 2018Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to…
• 10136780Apr 16, 2018Engine cooling. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil…
• 10136787Apr 5, 2018Equipment. Some vehicles may exhibit BLUETOOTH® hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
• 10136784Apr 5, 2018Air bags. This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.
• 10136772Apr 5, 2018Equipment. The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters…
• 10136778Apr 2, 2018Transmission and drivetrain. The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 10136775Apr 2, 2018Engine cooling. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction…
• 10134945Mar 28, 2018Electrical system. Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07…
• 10134933Mar 28, 2018Equipment, Electrical system. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10134930Mar 26, 2018Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10134929Mar 26, 2018Electrical system. The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10134928Mar 26, 2018Electrical system. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10134706Mar 26, 2018Seats. Some vehicles may exhibit inoperative driver and/or front passenger side seat warmer(s) in any mode (High, Mid and Low). This may be caused by repeated load applied to the seat cushion (1) while the seat is occupied. A section of the heater mat (2) just above the reinforcement rod (3) in the cushion pad contacts internal heater mat wire and causes damage (4).
• 10134703Mar 26, 2018Equipment. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is…
• 10134702Mar 22, 2018Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10134701Mar 22, 2018Exterior lighting. Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between…
• 10134700Mar 22, 2018Suspension. Beginning with the CX-5, grip type front and rear stabilizer bushings have been incorporated for noise prevention purposes. If any type of grease or lubrication is applied to the bushings, it may create noise due to bushing slippage.
• 10134699Mar 22, 2018Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10134934Mar 20, 2018Fuel system. The SKYACTIV®-G 2.5T engine requires a unique oil filter (PY8W-14-302) which is NOT interchangeable with other SKYACTIV® oil filters. The unique oil filter can be identified with two white bands as shown below.
• 10134691Mar 9, 2018Engine, Engine cooling. When the engine is started for the first time after parking the vehicle overnight in cold conditions (below 32 degrees Fahrenheit / 0 degrees Celsius), some vehicles may exhibit a rough idle and/or the check engine light on with any of the following DTC(s) stored in memory. P0300 - Random misfire detected P0301 - Cylinder No.1 misfire detected P0302 - Cylinder No.2 misfire detected P0303 - Cylinder No.3 misfire…
• 10136325Feb 22, 2018Engine cooling, Fuel system. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded P0524:00 - Engine oil pressure too low This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10134925Feb 16, 2018Equipment, Air bags. The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
• 10129574Jan 29, 2018Seats. Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction…
• 10129564Jan 5, 2018Suspension. Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the…
• 10129353Jan 4, 2018Equipment. The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
• 10185794Dec 18, 2017Electrical system, Air bags. Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.
• 10129327Dec 18, 2017Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10129368Dec 5, 2017Engine, Equipment. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10188487Nov 20, 2017Fuel system, Engine cooling, Equipment. Some vehicles may exhibit an oil leak from the companion flange area (A) of the transfer unit. This concern may be caused by companion flange oil seal wear. The oil seal has been improved to increase the wear resistance.
• 10188482Nov 13, 2017Equipment, Electrical system, Seats. Some vehicles may exhibit excessive noise when operating either front power seat forward or backward. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the case due to inadequate fabric wrapped around the cable. The fabric thickness has been increased to eliminate the noise.
• 10188481Nov 10, 2017Suspension, Equipment, Body and structure. Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold.

← All problems reported for the 2013 Mazda CX-5