2017 Mazda CX-5 Technical Service Bulletins

572 technical service bulletins (TSBs) are on record for the 2017 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10134915Feb 6, 2018Other or unknown. Some repair kits (p/n 0000-8E-R09) for Recall 1617K (2017 CX-5 - EQUIPPED WITH A GENUINE MAZDA ACCESSORY TRAILER - HITCH HARNESS) may contain an extra wire harness (shown below). The extra wire harness is not necessary for the repair and should be removed and discarded from the repair kit. Only the trailer side of the wire harness should to be used.
• 10129571Jan 18, 2018Forward collision avoidance. Some customers may experience the following symptom relating to the Forward Sensing Camera (FSC)with DTC C1001:92 [Forward sensing camera (FSC) poor field of view] stored in memory.When the visibility out the windshieldis poor (i.e. fog or raining at night), the following warning lights mayilluminate.
• 10129569Jan 16, 2018Electrical system. Some customers may complain that the Voice Recognition system does not recognize "Address" or "New Destination" navigation voice commands. This may be caused by faulty navigation SD card software. The SD card has been updated to eliminate this concern.
• 10129567Jan 10, 2018Electrical system. Some customers may complain that the Voice Recognition system does not recognize "Address" or "NewDestination" navigation voice commands. This may be caused by faulty navigation SD card software. TheSD card has been updated to eliminate this concern.
• 10129566Jan 9, 2018Electrical system. After the installation of a new instrument cluster, the message "Fctry" or "Factory" is displayed instead ofthe odometer. This concern may also occur when a room fuse is installed in a new vehicle.Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.NOTE: The concern is applicable to Calsonic Kansei instrument clusters.
• 10129565Jan 8, 2018Equipment. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during coldtemperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interiorwarms up. This is caused by some for the MAZDA CONNECT navigation system SD cards beingmanufactured with improper hardware, resulting in a data reading error during cold temperatures. To correctthe concern, the SD…
• 10129564Jan 5, 2018Suspension. Some vehicles may exhibit a knocking / squeaking noise from the front shock absorber when driving onrough roads and/or when turning the steering wheel while the vehicle is stopped.The noise may be due to: Upper front strut bearing (A) damage. (CX-5 and Mazda6) Squeak type noise between the front strut bearing and coil spring. (CX-3, CX-5 and Mazda6) The bump stopper (C) may be contacting the strut bearing when the…
• 10129353Jan 4, 2018Equipment. The MAZDA MOBILE START (MMS) is currently experiencing a system disruption. User web portal and Call center web portal functions are affected. Mazda is working on this issue and will notify dealers when MMS service has been fully restored. We apologize for any inconvenience this may have caused you or your dealer.
• 10129354Jan 2, 2018Electrical system. When installing a navigation SD card, the center display may show error message "Invalid SD Card". This may be caused by: The navigation SD card lock tab is locked.The navigation SD card has a VIN mismatch due to SD card swapping.The navigation SD card has a malfunction.
• 10129351Dec 22, 2017Electrical system. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction.
• 10185794Dec 18, 2017Electrical system, Air bags. Some vehicles may experience the CHECK ENGINE LIGHT OIN with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A removed * P2610 Instrument cluster internal engine off timer performance problem * P2507 PCM battery voltage low input.
• 10129368Dec 5, 2017Engine, Equipment. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10188496Nov 29, 2017Tires, Equipment, Wheels. Mazda is incorporating a "Direct" type TPMS, which is unlike the previous "Indirect" type system. With the "Direct" type TPMS........ ? there is no TPMS switch on the dashboard. It is no longer needed. ? the wheel sensors activate after detecting tire rotation. ? the wheel sensors transmit data to the vehicle at a rate of once per minute. ? the vehicle must be driven at 16 mph or more for two (2) minutes or more to…
• 10188481Nov 10, 2017Suspension, Equipment, Body and structure. Some vehicles may exhibit a crack on the front shock absorber dust boot (A). This may be caused by dust boot insufficient resistance to cold. The shape and material of the dust boot has been changed to improve the resistance to cold.
• 10188491Nov 9, 2017Electrical system. The MODE switch operation for the Mazda Radar Cruise Control (MRCC) system has been changed as follows: Previous - Press the MODE switch to switch to the cruise control function. New - Press the MODE switch and hold for 2 seconds_ to switch to the cruise control function.
• 10188489Nov 9, 2017Equipment, Seat belts, Air bags, Seats. Some customers may complain about: PASSENGER Seat Belt and PASS AIRBAG OFF indicator lights ON (A). Front seat warmers ON (B) and cannot be turned OFF.No DTC's are stored in memory. This may be caused by water contamination at connector C-56 after a recent aftermarket windshield tint installation.
• 10188492Nov 6, 2017Body and structure, Equipment, Electrical system. If you receive a customer complaint of an excessive gap between decoration panel and switch panel (as shown below), repair it according to the repair procedure below.
• 10188488Nov 2, 2017Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10125469Oct 18, 2017Forward collision avoidance. The Smart City Brake Support (SCBS) system alerts the driver of a possible collision using an indication in the display and a warning sound when the Forward Sensing Camera (FSC) detects a vehicle ahead and determines that a collision with a vehicle ahead is imminent. In addition, the system reduces damage in the event of a collision by operating the brake control when the system determines that a collision is…
• 10123439Oct 6, 2017Brakes, Back-over prevention (rear camera), Electrical system. Some customers may complain about one or more warning lights ON when they start the vehicle during hot weather. The following DTCs are stored in memory: U3000:98 - Forward sensing camera (FSC) stops functioning due to temporary high temperature. U3000:04 - Forward sensing camera (FSC) internal malfunction.
• 10118754Sep 13, 2017Equipment, Electrical system. IDS SOFTWARE VERSION 107 AVAILABLE ON MGSS - PLEASE UPDATE YOUR PC'S. Upgrade your PCs to IDS version 107.00 and 107.01 from the previous version.
• 10120384Sep 8, 2017Equipment. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a clogged heater unit. For Mazda6 and CX-5, the check engine light may illuminate with the DTC P011A:00 stored at the same time. P011A:00 ECT sensor No.1/No.2 performance problem. NOTE: Refer to TSB 01-015/15 if the customer is using a block heater at temperatures below freezing.
• 10118751Sep 1, 2017Forward collision avoidance, Exterior lighting. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC). In other cases this DTC might be found without a related customer concern.
• 10118472Aug 23, 2017Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10118471Aug 22, 2017Suspension, Steering. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is turned to the full left position. NOTE: The noise will not occur if the steering wheel is in the center or full right position. The noise is caused when the edge (A) of the left side inner ball joint (B) gets stuck with the steering gear…
• 10118480Aug 18, 2017Electrical system, Exterior lighting. Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Instrument Cluster Multi-Information Display warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction.
• 10118479Aug 10, 2017Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. MAZDA CONNECT Symptom Troubleshooting Table Sections: Audio System, Bluetooth®, Center Display, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux, Voice Command
• 10118468Aug 9, 2017Exterior lighting, Electrical system, Body and structure. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No.
• 10118467Aug 7, 2017Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10111043Jul 26, 2017Equipment. Some customers may complain about the following MAZDA CONNECT Temperature Warning message: Display is too Hot. Screen performance may be decreased until it cools. The warning message displays when the MAZDA CONNECT screen temperature is above 176 degrees Fahrenheit (80 degrees Celsius).
• 10111039Jul 21, 2017Equipment, Electrical system. Some customers may complain about one or more warning lights on when they start the vehicle during hot weather. The combination of warning lights mentioned by the customer may include: SCBS, LDWS, HBC. Instrument Cluster Multi-Information Display warning messages may include: Forward Smart City Brake Support Malfunction, Smart Brake System Malfunction, Front Camera Sensor System Malfunction.
• 10111038Jul 21, 2017Electrical system, Equipment. Some customers may complain about the "wrong" phone is connected to the infotainment system. MAZDA CONNECT bluetooth will connect all profiles to devices in order of priority if the last device is not available. This concern may be a normal operation of the CMU connecting to available devices on start up.
• 10111037Jul 19, 2017Body and structure, Interior lighting. On some 2017 CX-5s, the Accessory Lighted Door Sill Trim Plate (DSTP) accessory may not light up after installation. This is likely caused by an incorrect magnet location. The current installation instructions suggest that the installer close the door firmly with a light slam when installing the magnet, other wise the magnet will end up in an incorrect location. To make sure the magnet location is correct during…
• 10120373Jul 12, 2017Electrical system. All Mazda Connect vehicles in new car inventory must be updated to this software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502 or later).
• 10111036Jul 12, 2017Electrical system. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is© 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.
• 10111044Jul 11, 2017Electrical system. There is a minor error with the Controller Programming instructions included with the accessory remote start kit C960-V7-620. In the current "Registration (programming) of the controller" instructions, step 5 shows an incorrect image. The function button is the lower button. A revised set of instructions are available in the Accessory E catalog and will be included in all kits at the next revision point.
• 10111042Jul 6, 2017Electrical system, Transmission and drivetrain. Whenever you are reprogramming a PCM or any other module, always use the GR8 Battery Charger in the Power Supply mode to prevent the battery from discharging.
• 10111034Jul 6, 2017Visibility (wipers, defrost, mirrors). CAUTION: DO NOT attempt any repair of the windshield damaged by stone chipping/cracks at the area in front of the Forward Sensing Camera (FSC) and Laser Sensor. Replace the windshield with a new one instead.
• 10111033Jul 6, 2017Exterior lighting. High Beam Control (HBC) system frequently asked questions (FAQ)
• 10111032Jul 6, 2017Forward collision avoidance. Mazda Radar Criose Control (MRCC) system frequently asked questions (FAQ)
• 10111030Jul 6, 2017Lane departure. Blind Spot Monitoring (Advanced BSM) system frequently asked questions (FAQ)
• 10111029Jul 6, 2017Lane departure. Lane Departure Warning System (LDWS) frequently asked questions (FAQ)
• 10111028Jul 6, 2017Brakes. Smart City Brake Support (SCBS) frequently asked questions (FAQ)
• 10111022Jun 13, 2017Equipment, Electrical system. There are a few issues with the accessory C960-V7-620 remote start kit instructions. In the current ?Registration (programming) of the controller? instructions, step 5shows an incorrect image. The function button is the lower button. The correct set of instructions are below. The instructions for registration of additional remotes is not available on the E-catalog web site at this time. The instructions are below…
• 10120348Jun 5, 2017Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.502or later).NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will removed from the Active Driving Display as part of Mazda?s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the software.
• 10111021Jun 5, 2017Electrical system. In order to do a CMU data retrieval for the new MAZDA CONNECT software, make sure to use version 31 (available on MGSS).
• 10120347Jun 2, 2017Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance.This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10186335May 24, 2017Electrical system. Fctry MESSASGE DISPLAYED after instrument cluster replacement. After the installation of a new instrument cluster, the message "Fctry" is displayed instead of the odometer. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.
• 10186334May 22, 2017Electrical system. Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.
• 10118129May 22, 2017Electrical system. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom.

← All problems reported for the 2017 Mazda CX-5