2011 Mazda CX-9 Technical Service Bulletins

296 technical service bulletins (TSBs) are on record for the 2011 Mazda CX-9. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10148003Oct 10, 2018Brakes, Equipment. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims…
• 10148002Oct 10, 2018Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle- specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10145237Sep 14, 2018Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10145240Sep 11, 2018Engine cooling. EXHAUST PIPE GASKET OPEN END: There has been some concern with the open end of hoop design being considered a defect in the gasket for P/N AJ17-40-305. The end of this ?hoop? is intentionally modified to press fix the gasket on the exhaust pipe. NOTE: The ?hoop? might become larger during shipping, but you can still use it by pressing this portion down when installing.
• 10145242Sep 6, 2018Engine cooling. On some vehicles, a sulfur smell or 'rotten egg' odor may be noticed coming from the exhaust system. The odor is usually noticed after a cold start, fast idle, extended periods of idling and full throttle acceleration. Sulfur smell is not an indication of an engine concern and will not cause reduced driveability or durability of the engine or any of its emission components. The sulfur smell or 'rotten egg' odor is…
• 10144333Aug 31, 2018Vehicle speed control. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10143973Jul 30, 2018Wheels. Some vehicles may have aluminum alloy type wheel(s) with one of the following paint damage conditions shown in the sample photos below. The damage extends to the front surface of the aluminum wheel partly or entirely.
• 10144010Jul 20, 2018Electrical system, Equipment. ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of…
• 10143965Jun 20, 2018Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following…
• 10142527May 11, 2018Equipment. Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement.
• 10142517May 11, 2018Engine cooling. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
• 10142515May 11, 2018Brakes. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare…
• 10142525May 8, 2018Equipment. When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).
• 10142519May 8, 2018Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road.
• 10136776Apr 27, 2018Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10136774Apr 27, 2018Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10136782Apr 16, 2018Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to…
• 10136787Apr 5, 2018Equipment. Some vehicles may exhibit BLUETOOTH® hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
• 10136784Apr 5, 2018Air bags. This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.
• 10136777Apr 2, 2018Transmission and drivetrain, Equipment. Always be sure to use the correct automatic transmission fluid when replacing ATF. Using the wrong ATF may cause shift quality complaints or may even damage the transmission. NOTE: ATF M-V (TYPE M5) IS NOT THE SAME FLUID AS MERCON®V OR MERCON®LV ATF. ATF M-V (TYPE M5) HAS A GREATER VISCOSITY THAN MERCON®V AND MERCON®LV ATF IN LOW TEMPERATURES. ATF M-V (TYPE M5) HAS A GREATER ANTI-JUDDER SPECIFICATION THAN MERCON®V…
• 10136775Apr 2, 2018Engine cooling. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction…
• 10134933Mar 28, 2018Equipment, Electrical system. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10134930Mar 26, 2018Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10134929Mar 26, 2018Electrical system. The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10134928Mar 26, 2018Electrical system. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10134703Mar 26, 2018Equipment. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is…
• 10134702Mar 22, 2018Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10134701Mar 22, 2018Exterior lighting. Some customers may complain of condensation/fog inside the front (headlamp/headlight) or rear (taillamp/taillight) combination lights. The recent new models have been fitted with a clear lens which can cause the symptom to be more noticeable, however, it does not affect the performance of the light. This condensation/fog is a natural phenomenon that occurs when there is a fairly large temperature difference between…
• 10134699Mar 22, 2018Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle-specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10134925Feb 16, 2018Air bags, Equipment. The Workshop Manual has two-different airbag procedures, one for Standard Deployment and one for Two-Step Deployment. Standard Deployment is for Mexico spec vehicles and Two-Step Deployment is for US and Canadian spec vehicles.
• 10134916Feb 6, 2018Engine. ome customers may complain of a check engine light on while driving the vehicle. If DTCs P2A04:00, P2272:00 and/or other DTCs are found during diagnosis, follow the repair procedure below. P2A04:00 - HO2S (LH) circuit range/performance, P2272:00 - HO2S (LH) signal stuck lean
• 10188488Nov 2, 2017Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10120388Sep 12, 2017Suspension. Some vehicles may experience a knocking noise from the front and/or rear shock absorbers when driving over rough roads or speed bumps. The noise may be caused by damage to the inner seal of shock absorber, resulting in fluid seepage. To eliminate this concern, modified parts with improved oil sealing performance have been established as service parts.
• 10118753Sep 12, 2017Air bags. STOPPER PLATES FOR AIR BAG MODULE CONNECTORS HAVE BEEN ESTABLISHED AS NEW SERVICE PARTS. When removing the connector (1) to the air bag module (2), make sure to first lift the stopper plate (3) carefully using a flathead screwdriver (but do not remove it), and then pull out the connector.
• 10118468Aug 9, 2017Body and structure, Electrical system, Exterior lighting. When dealing with customer complaints of excessive condensation and/or water within the headlamp unit, first determine if all the bulb sockets (including O-ring), seals and covers are present and correctly installed. In most cases you will find that the Bulb Seal No. 1 (A) or HID Bulb Seal No. 1 (B) and Bulb Seal No.
• 10118467Aug 7, 2017Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer?s responsibility to comply with Federal, State, and local laws concerning odometerand related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with…
• 10120375Jul 21, 2017Suspension. Some vehicles may experience a knocking noise from the front shock absorbers when driving over rough roads or speed bumps. The noise may be caused by damage to the inner seal of front shock absorber, resulting in fluid seepage. To eliminate this concern, modified parts with improved oil sealing performance have been established as service parts.
• 10111036Jul 12, 2017Electrical system. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is© 2017 Mazda North American Operations, U.S.A. allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service.
• 10111031Jul 6, 2017Lane departure. Blind Spot Monitoring (BSM) system frequently asked questions (FAQ)
• 10120365Jun 30, 2017Suspension. Some vehicles may experience a knocking noise from the front shock absorbers when driving over rough roads or speed bumps. The noise may be caused by damage to the inner seal of front shock absorber, resulting in fluid seepage. To eliminate this concern, modified parts with improved oil sealing performance have been established as service parts.
• 10186334May 22, 2017Electrical system. Display shows inaccurate ambient temperature. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature.
• 10118129May 22, 2017Electrical system. Some customers may complain that the ambient temperature display is not accurate, or it takes too long for the display to show actual temperature. When you encounter a customer with this concern, first verify the condition when the customer noticed this symptom.
• 10186342May 18, 2017Transmission and drivetrain, Equipment. Abnormal Noise & Oil Leak from power transfer Unit Warranty Extension Program - Special Service Program (SSP) 92 extended.
• 10116228May 18, 2017Equipment, Engine cooling. In relation to on-going warranty extension program SSP92 (effective from April 2014), which extended the warranty coverage for power transfer unit (PTU) replacement on certain 2010-2014 CX-9 vehicles with AWD, Mazda Motor Corporation has decided to additionally include certain 2014-2015 CX-9 vehicles in this SSP92.The warranty coverage for specific repair of power transfer unit (PTU) on certain 2014-2015 CX-9…
• 10111011Mar 9, 2017Exterior lighting. Take caution when cleaning plastic headlight lenses. Damage can occur when using some cleaners that contain strong acid, alkaline cleanser or organic solvent. Damage caused by using these cleaners is not covered by Mazda's New Vehicle Limited Warranty term.
• 10185809Jan 13, 2017Body and structure. Driver and/or passenger sunvisors drop by themselves
• 10186247Dec 7, 2016Equipment, Transmission and drivetrain. Engine Surge and/or shift shock. Some vefhicles may experience one or more of the following concerns: * Engine surging c oncern when the vehicle is driven up hill with the cruise control ON. * Shift shock when shifting from N, R or from P to D * Shift shock when down shifting from 5 to 4.
• 10092487Aug 11, 2016Equipment. Raising a vehicle with a jack can be dangerous if not done properly. The vehicle can slip off the jack and seri-ously injure someone. In this service information, some important warnings and cautions have been taken from the owner’s manual. For mazda customers who have questions about safely lifting their vehicle to change a flat tire or to install snow chains, please provide a copy of the attached handout for them.
• 10085405Jul 28, 2016Air bags. Takata recalls general information purpose: this page was created to assist with handling takata air bag recalls. Processes: please use these process flowcharts to properly handle vehicles subject to the takata air bag recall. Recall 8215f & 9416e preliminary parts process recall 9516e & 9616e preliminary parts process general information: the links below contain the latest takata recalls information. The documents…
• 10091610Jul 22, 2016Body and structure. When removing parts from a vehicle, take caution of this symbol "r". Failing to replace the non-reusable part may cause a system failure.

← All problems reported for the 2011 Mazda CX-9