2016 Mazda CX-9 Technical Service Bulletins

613 technical service bulletins (TSBs) are on record for the 2016 Mazda CX-9. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10144334Aug 15, 2018Transmission and drivetrain. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration.
• 10144325Aug 9, 2018Brakes, Engine cooling, Engine. After parking the vehicle at temperatures below the freezing, some customers may experience a lack of power with the check engine light on and DTC P0638:00 and/or P2112:00 stored in memory. - P0638:00: Throttle valve actuator control range/performance problem (one drive cycle DTC) - P2112:00: Throttle valve actuator motor current range/performance problem (one drive cycle DTC) This concern may be caused by…
• 10143982Jul 30, 2018Electrical system. MAZDA MOBILE START (MMS) APP ERROR MESSAGE INSTALLED ON ANDROID DEVICES: Customers may get an error message "Device no longer has access or service." for the MMS APP installed on android devices starting 8/1/18. Inform the customer that all they need to do is update the MMS APP to the latest version to get rid of the error message.
• 10143975Jul 30, 2018Brakes. Some vehicles may exhibit a squeaking noise from the front brakes during light braking. This concern usually occurs when the front brake pads have been worn to certain levels. Also, as the pads wear, the chamfer goes away and the grease between the pad and the shim deteriorates.To eliminate this concern, the chamfer shape of the brake pad has been modified to increase its durability.
• 10143973Jul 30, 2018Wheels. Some vehicles may have aluminum alloy type wheel(s) with one of the following paint damage conditions shown in the sample photos below. The damage extends to the front surface of the aluminum wheel partly or entirely.
• 10143970Jul 30, 2018Engine. Some vehicles may exhibit an engine misfire during acceleration with the check engine light flashing and the following DTC(s). P0302:00 - Cylinder No.2 misfire detected and/or P0303:00 - Cylinder No.3 misfire detected NOTE: Even if a misfire occurred, the DTCs may not be stored because they are set after the continuous misfire occurred for 2 drive cycles. In this case, check if the following information is…
• 10144013Jul 20, 2018Engine, Equipment. ENGINE NO START (KEY NOT DETECTED): Some customers may complain about the following: Intermittent engine no start, Instrument cluster red security indicator light ON, Engine Start/Start Button Amber indicator light flashing.
• 10144012Jul 20, 2018Electrical system, Engine, Visibility (wipers, defrost, mirrors). ENGINE NO START AND / OR REAR VIEW MONITOR DISPLAY IS BLURRY DUE TO AFTERMARKET ELECTRICAL DEVICE: Some customers may complain about the following: Engine no start. A blurry rear view monitor display. This may be caused by an aftermarket accessory device. Some aftermarket electrical devices (e.g., an accessory cell phone charger) may create excessive electrical noise. The noise may interrupt some of the vehicle…
• 10144010Jul 20, 2018Electrical system, Equipment. ELECTRICAL CONCERN AND/OR MULTIPLE DTC'S DUE TO AFTERMARKET DEVICE: If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of…
• 10143980Jul 16, 2018Equipment. Mazda connect system frequently asked questions (faq)
• 10143977Jul 13, 2018Seats. Some vehicles may exhibit excessive operating noise when sliding the driver and/or passenger power seat(s) back and forth. The noise may be caused by cable vibration, which transmits power from the motor to the gears. The cable vibrates inside the cable casing due to inadequately wrapped fabric around the cable. To eliminate this concern, the power seat cable has been changed to a type that produces less friction…
• 10143974Jul 13, 2018Suspension. Some vehicles may exhibit a crack on the front shock absorber dust boot (1). This may be caused by the dust boot having insufficient resistance to the cold. The shape and material of the dust boot has been changed to improve its resistance to cold.
• 10144011Jul 3, 2018Body and structure, Electrical system. POWER LIFTGATE INOPERATIVE WITH DTC U3003:16: Some customers may complain about an inoperative power liftgate (PLG) with DTC U3003:16 (Power liftgate (PLG) control module power supply voltage low input) is stored in memory. This may be caused by low vehicle battery voltage.
• 10143957Jun 27, 2018Equipment. When troubleshooting a radar unit, DO NOT swap it with another vehicle. Radar units are configured to the original vehicle, and if installed in another vehicle, a configuration error will occur. Refer to MGSS (RADAR UNIT INSPECTION) for proper diagnosing.
• 10143965Jun 20, 2018Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.Customers experiencing related concerns should have their vehicle and/or device inspected according to the following…
• 10143964Jun 6, 2018Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 59.00.546 or later). NOTE: For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda's continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10143955Jun 6, 2018Engine cooling. IMPORTANT: If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any key after reading the notifications about the…
• 10142534May 23, 2018Seat belts, Air bags. Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.
• 10142527May 11, 2018Equipment. Mazda infotainment systems require contacting the proper source for diagnostic support, parts authorization, and parts exchange. Some components require prior authorization before ordering as exchange. Refer to DAG Exchange Central (MXConnect>Parts and Accessories>Parts>Programs>Exchange Central) for component availability, source of technical support and prior authorization requirement.
• 10142517May 11, 2018Engine cooling. Some vehicles may exhibit the check engine light on with DTC P0456 stored in the PCM memory. P0456: EVAP system leak detected (very small leak)The concern is most likely the result of the customer not getting the fuel cap completely closed after fuelingthe vehicle. This causes a small fuel vapor leak and turns DTC P0456 on.
• 10142515May 11, 2018Brakes. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAOauthorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorizedequipment program.NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claimsare…
• 10142533May 8, 2018Engine. If a vehicle is driven on extremely short trips most of the time (where the engine never reaches normal operating temperature), the engine oil may become diluted with fuel and the engine oil level will increase. Engine oil dilution with fuel occurring under this specific driving condition is normal with direct injection engines.
• 10142525May 8, 2018Equipment. When replacing the SiriusXM satellite radio unit (or a MAZDA CONNECT tuner and amp unit (TAU)) with replacement tuner for any reason, a call must be made to inform SiriusXM of the existing Radio ID and the new/replacement SAT Radio ID as soon as possible to ensure the customer leaves the dealership with active (working SAT radio).
• 10142520May 8, 2018Tires. This service bulletin illustrates the conditions when a TPMS warning light may illuminate, why it illuminated and how to properly initialize the system.The Tire Pressure Monitoring System (TPMS) monitors the tire pressure of all four tires indirectly using the data sent from the ABS wheel speed sensors.
• 10142519May 8, 2018Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road.
• 10142516May 8, 2018Engine. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored inmemory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service. P2507 in this…
• 10142518May 7, 2018Tires. Customer complaints have been reported where the TPMS warning light is unnecessarily illuminated because the TPMS initialization was not performed correctly before customer delivery.TPMS INITIALIZATION PROCESS: When any of the services below is performed, BE SURE TO INITIALIZE THE TPMS BEFORE DRIVING THE VEHICLE by pushing and holding the TPMS Set Switch on the dash until the TPMS warning light flashes two times…
• 10142531May 3, 2018Body and structure. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10142530May 1, 2018Lane departure, Exterior lighting. Some vehicles may have DTC C1001:92 stored in memory. DTC C1001:92 sets as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure Warning System (LDWS) and/or High Beam Control system (HBC).
• 10136776Apr 27, 2018Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10136774Apr 27, 2018Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10136771Apr 27, 2018Engine cooling. Some vehicles may exhibit an engine misfire during acceleration with the check engine light flashing and the following DTC(s). P0302:00 - Cylinder No.2 misfire detected and/or P0303:00 - Cylinder No.3 misfire detected NOTE: Even if a misfire occurred, the DTCs may not be stored because they are set after the continuous misfire occurred for 2 drive cycles. In this case, check if the following information is…
• 10136773Apr 20, 2018Suspension. Some vehicles may exhibit one or more of the following noises from the front suspension: 1. A creaking noise from under the front of the vehicle (front lower arm bushing) when driving over bumps at approximate 12 - 25 mph (20 - 40 Km/h). The noise occurs when the road surface is wet or after the vehicle has been washed. The noise becomes more noticeable as the bumps get higher. The creaking noise is caused by the…
• 10136782Apr 16, 2018Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/Cevaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available to…
• 10136780Apr 16, 2018Engine cooling. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil…
• 10136766Apr 16, 2018Engine cooling. While inspecting turbocharger housings, you may see cracks (fractures) as shown below. The cracks do not affect engine performance or cause any noise, so replacement is NOT necessary.
• 10136788Apr 5, 2018Body and structure. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.
• 10136787Apr 5, 2018Equipment. Some vehicles may exhibit BLUETOOTH® hands-free and/or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010. Customers experiencing related concerns should have their vehicle and/or device inspected according to the following procedure.
• 10136784Apr 5, 2018Air bags. This information is provided to help address Passenger Airbag Deactivation (PAD) Indicator illumination concerns during vehicle service.
• 10136772Apr 5, 2018Equipment. The vehicles listed above are equipped with a push button start/stop ignition system. Unlike previous Mazdamodels, there is no key cylinder on the steering column. Therefore, the engine cannot be started with theauxiliary key if the room fuse is removed or if the transmitter battery is dead.NOTE: The auxiliary key can only be used to lock or unlock the doors. It cannot be used to start the engine. Two transmitters…
• 10136778Apr 2, 2018Transmission and drivetrain. The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use"ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 10136775Apr 2, 2018Engine cooling. Some customers may report a slight clunk/bang/buzz noise or jolt from the front of the vehicle. This concern will most likely occur during the vehicles first forward movement after starting the engine. This is a normal operating noise of the Anti-Lock Brake System (ABS). Do not attempt any repairs. If you encounter a customer complaint for this concern, explain that the noise comes from the ABS/TCS/DSC "Malfunction…
• 10134931Mar 29, 2018Engine. Some vehicles may exhibit an engine misfire during acceleration with the check engine light flashing and the following DTC(s). P0302:00 - Cylinder No.2 misfire detected and/or P0303:00 - Cylinder No.3 misfire detected. NOTE: Even if a misfire occurred, the DTCs may not be stored because they are set after the continuous misfire occurred for 2 drive cycles. In this case, check if the following information is…
• 10134945Mar 28, 2018Electrical system. Upgrade your PCs to IDS version 109.00 and 109.01 from the previous version. NOTE: You may see ?Selection not available? on IDS when a selecting ?Programming menu?, 108.07 included a timer extension for Programming menu application that had to be installed before the expiration date of 3/27/18. After the expiration, IDS can?t accept the extension. To correct this, uninstall IDS and re-install IDS 108.00 >IDS 108.07…
• 10134933Mar 28, 2018Equipment, Electrical system. If you encounter any type of electrical concern (e.g, dead battery), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10134930Mar 26, 2018Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10134929Mar 26, 2018Electrical system. The Mazda GR8-1291 is required for all warranty battery testing. If the Mazda GR8-1291 is not used, incorrect battery testing may result in unnecessary battery replacement. Use the following test procedures in this Service Bulletin to test Mazda vehicle batteries and to generate a Warranty Code.
• 10134928Mar 26, 2018Electrical system. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10134703Mar 26, 2018Equipment. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is…
• 10134704Mar 22, 2018Equipment. Some customers may experience a navigation system screen that shows the wrong location. This concern is due to poor reception of the GPS signals. To eliminate this concern, the CMU hardware has been modified.

← All problems reported for the 2016 Mazda CX-9