2017 Mazda CX-9 Technical Service Bulletins

513 technical service bulletins (TSBs) are on record for the 2017 Mazda CX-9. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10185817Feb 8, 2017Electrical system. Stopper plates for air bag module connectors have been established as new service parts
• 10185813Feb 8, 2017Equipment, Electrical system. If you experience issues with the current version of ID's such as missing tools or modules not showing after completing a network test, be advised that we are aware of these issues and are working to resolve them. As a counter measure, it is advised that you un-install ids and re-install version 103.00 and "do not update" until further notice.
• 10185810Jan 23, 2017Electrical system. All models - Stopper plates for air bag module coinnectors
• 10185793Jan 19, 2017Back-over prevention (rear camera), Suspension, Electronic stability control. In support of the 2016-17 Mazda CX-9, Mazda will make available a Special service tool (SST) to address front suspension noise for specific highly humid and wet climate conditions of the lower Gulf States and Hawaii. The SST will be needed to complete repairs detailed in TSB 02-003/17, and is available through Mazda's tool vendor, Snap on Tools
• 10185792Jan 19, 2017Equipment, Body and structure. Special Service Tool Shipment - January 2017. In support of the 2014 - 17 Mazda6 and 2016-17 Mazda CX-9, Mazda will ship to all dealers a new Special Service Tool (SST) * The SST will be shipped by Mazda's toool vendor Bosch in the month of January, 2017 * The following SST is the latest addition to the Mazda required tool (MRT).
• 10186261Dec 22, 2016Electrical system, Lane departure, Equipment. Multi-Model - Blind Spot Monitoring (BSM) System Change (update)
• 10186263Dec 19, 2016Electrical system, Equipment. MAZDA Mobile start (MMS) cannot communicate with vehicle
• 10186256Dec 2, 2016Equipment, Electrical system. Fctry MESSAGE DISPLAYED AFTER INSTRUMENT CLUSTER REPLACEMENT. After the installatioin of a new instrument cluster, the message "F ctry" IS DISPLAYED INSTEAD OF THE ODOMETER. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required.
• 10186918Oct 7, 2016Electrical system. New IDs software version 102.00 and Update 102.01 is now available on MS3 IDs update 102.00 and 102.01 is now available on MS3 under the "IDs/Infotainment" tab.
• 10084957Aug 16, 2016Equipment. Bsm system vehicle detection has changed. Although the overall function is the same as previous vehicles, vehicle detection is different. For detailed bsm system information, refer to service highlights.
• 10092487Aug 11, 2016Equipment. Raising a vehicle with a jack can be dangerous if not done properly. The vehicle can slip off the jack and seri-ously injure someone. In this service information, some important warnings and cautions have been taken from the owner’s manual. For mazda customers who have questions about safely lifting their vehicle to change a flat tire or to install snow chains, please provide a copy of the attached handout for them.
• 10084949Aug 10, 2016Equipment. When installing a navigation sd card, confirm that the card is unlocked. Also, mazda does not recommend swapping navigation system sd cards from one vehicle to another for testing. If swapped, the sd card that is installed into the other vehicle becomes “linked” to the vin of that vehicle.
• 10091610Jul 22, 2016Body and structure. When removing parts from a vehicle, take caution of this symbol "r". Failing to replace the non-reusable part may cause a system failure.

← All problems reported for the 2017 Mazda CX-9