2024 Mercedes-Benz E350 Technical Service Bulletins

163 technical service bulletins (TSBs) are on record for the 2024 Mercedes-Benz E350. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11026127Dec 3, 2025Electrical system. Complaint Displayed Message: “Driver camera not functioning, see Operator’s Manual” Cause Interior temperature too high due to: • Summer heat • Direct sunlight • Lack of air conditioning or ventilation Camera enters self-protection mode to prevent overheating. Remedy Do NOT replace any parts. The driver camera (NTG7: MDC295; CIVIC.i2: CIVIC206) is operating as designed. Allow the interior to cool down.
• 11025646Nov 18, 2025Electrical system. Complaint USB port not functioning properly. Cause Most reported USB port issues are due to improper use or contamination. Note: Any repair costs must be discussed with the customer beforehand. Common external factors identified include: • Fluid intrusion • Broken bushings or physical damage See attachments. Remedy If a component needs replacement but shows no visible external damage, submit a detailed TIPS case…
• 11025150Nov 5, 2025Transmission and drivetrain. Complaint A harsh 5-4 downshift can be felt during deceleration while braking or coasting. It may be mistaken for a hard brake engagement Cause Poor learning of brake B06 adaptation values over time. Remedy Short-term remedy: 1. Perform IPR and follow the instructions. 2. Perform resetting of deceleration values (VGS > Special Procedures > Special procedure > Resetting learned values Deceleration mode) 3. Perform…
• 11025100Nov 3, 2025Transmission and drivetrain. Complaint Only vehicles with a variable transfer case are affected. This can be identified through control unit N45 or N15/7 in the quick test. When accelerating with light load, vibrations or jolting sensation may come from the drivetrain. It may be mistaken for a harsh shift. Cause Modified oil quality of the transfer case over time Remedy 1. Check initial quick test for faults in the following control units.
• 11024405Oct 20, 2025Brakes. Complaint At low speeds and light brake pressure, brakes will make a groaning or honking noise. Cause Frictional vibrations with very light brake pressure/modulations. Remedy This condition can be duplicated on most vehicles. To validate, use a like for like reference vehicle. The noise is normal behavior under the conditions listed. With very light brake pressure this noise can be induced/caused due to normal…
• 11024274Oct 10, 2025Electrical system. Complaint Clanking noise from the area of the speakers in the doors. Cause Under analysis. Remedy To narrow down the cause, first of all remove the door trim. • If the noise continues to occur even with the door trim removed, then continue the diagnosis working towards the speaker and if necessary, create a TIPS case with an informative video as an attachment.
• 11023650Sep 26, 2025Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain 2024 C-Class, E-Class, and GLC (206, 214, 254 platform) vehicles, the electronic ignition lock control unit does not correspond to current specifications. As a result, the ignition lock may not react after a key cycle, which could result in the vehicle not starting and the instrument cluster display not reacting. MBUSA will…
• 11023347Sep 25, 2025Electrical system. Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged…
• 11023194Sep 16, 2025Electrical system. Complaint After a software update from campaign 2025050001 of component LIB48_222 - G1/3 (48 V on-board electrical system battery) from software release A 000 902 50 48 to software release A 000 902 15 89, the fault code B183319 may be output. B183319 "The battery for the 48V on-board electrical system has a malfunction.
• 11023047Sep 5, 2025Electrical system. Complaint The Apple Music app is no longer available in the head unit apps menu after updating the software of the (A26/17 - MBUX multimedia system + instrument cluster (head unit)) to E333.8 / A236 904 19 00. Cause Head unit software (CIVIC206) Remedy NOTE: Do not replace any component parts A remedy is currently being developed and will be communicated once finalized. Once service is restored, the app will be…
• 11022923Sep 5, 2025Electrical system. Complaint One of the flush door handles (Also referred to as Seamless Door Handles) does not extend/retract (and/or) the KeylessGo sensor surfaces do not respond. Cause Multiple possible causes can be inferred from the table, see remedy (additionally as reference table in attachment). Remedy 1) KeylessGo sensor surfaces do not respond. Door handles can extend/retract if the key is used for locking/unlocking. No…
• 11022819Sep 5, 2025Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, there is a new software release for the MBUX Infotainment system. An OTA update will enhance both functionality and entertainment features. The update introduces Dolby Atmos support for in-car apps, improvements to the MBUX calendar app, and the launch of MBUX SOUND DRIVE.
• 11021154Jul 31, 2025Seats. Complaint The customer complains about squeaking/creaking noises on uneven roadways, on bends or when moving in their seat. Cause Noise in the backrest adjustment mechanism Remedy The adjustment mechanism is treated with dry lubricant spray A000 989 35 60 to rectify the noise. To do this, proceed as follows: • Move the seat to the front position and put the backrest into a lying position.
• 11020951Jul 25, 2025Forward collision avoidance, Electrical system, Lane departure. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has updated driver assistance system software available for certain subject vehicles. The updated software improves system stability and enhances the robustness of the driver assistance system. MBUSA will conduct an OTA service campaign. Remote software updates are automatically downloaded and installed in the customer’s vehicle free of charge and do not…
• 11020163Jul 2, 2025Suspension. Complaint Vehicle lifts and lowers again while driving. Cause Moisture may collect in the compressor of the air suspension over its lifetime, which can result in corrosion. Corrosion can result in reduced compressor performance or be deposited on the valve seats of the valve block and subsequently result in internal micro leakages. Remedy Update software for air suspension compressors as of 08/2022 or vehicles…
• 11019782Jun 28, 2025Lane departure, Forward collision avoidance, Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has updated driver assistance system SCN coding available for certain subject vehicles. The updated SCN coding improves system stability and enhances the availability of driver assistance features. MBUSA will conduct an OTA service campaign. Remote SCN coding updates are automatically downloaded and installed in the customer’s vehicle free of charge and…
• 11019746Jun 17, 2025Other or unknown. Complaint The intent of this document is to provide workshops with helpful technical reference language. • Commonly used acronyms in LI's and TIPS cases. • Control unit names, numbers, and how to identify. • Network/wiring architecture groups to baumuster quick reference. • Platform to baumuster quick reference.
• 11018712May 30, 2025Electrical system. Complaint MBUX head unit display with red text box "System Inoperative". ONLY for vehicles with SA code (549+21U) or (549+U19). Cause Head unit software variant. Remedy For all chassis use Xentry to update head unit (A26/17). Target boot software number should be either: • 247 904 6600 (E905.4) OR • 247 904 7500 (E906.1) If vehicle fits all criteria and either target software is not available via Xentry, please…
• 11018701May 29, 2025Seats. Complaint Squeaking or creaking noises on uneven roadways, in turns, or when moving in their seat. Cause Noise in the backrest adjustment mechanism Remedy The adjustment mechanism is treated with dry lubricant spray A000 989 35 60 to rectify the noise. To do this, proceed as follows: • Move the seat to the front position and put the backrest into a lying position. • Due to the risk of soiling on the left and right…
• 11019018May 21, 2025Transmission and drivetrain. Complaint Single throttle lift-off clunking noise from the side shaft when moving off (audible at the outboard end). The clunk is heard once when changing from forward to reverse (and vice versa). Note: Sound file in attachment Cause If the complaint is eliminated by experimentally loosening the outboard collar nut (by 1 turn), the problem is due to micromovement in the connection between the wheel bearing inner…
• 11018530May 15, 2025Engine. Complaint Check engine light illuminated Fault code stored in N3/10 control unit- P052E71 – Positive Crankcase Ventilation Regulator Valve Performance: The valve for crankcase ventilation has a malfunction Cause The partial-load ventilation valve (a part of the intake line assembly) may not work as intended. Remedy **Important** Replacement of the engine wiring harness or control unit is not needed if oil is found…
• 11018365May 14, 2025Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left…
• 11018297May 13, 2025Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the HLI control unit. Cause HLI control units processing of level sensor data. Remedy Update the software for the HLI control units - starting with the left (driver…
• 11018627May 10, 2025Engine. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the ME-SFI control unit software does not meet current production specifications. As a result, a check engine malfunction indicator lamp might erroneously be triggered.
• 11018164May 7, 2025Electrical system. Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document.
• 11018213May 2, 2025Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the coding for the electronic ignition lock control unit does not correspond to the latest series production configuration. The electronic ignition lock control unit will be updated to change the logic for locking and unlocking the vehicle via the door handles. To unlock the vehicle, the large outer…
• 11018206May 2, 2025Electrical system. Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM or EZS cannot record the data if the battery is discharged. Note: A discharged…
• 11018204May 2, 2025Forward collision avoidance, Steering, Lane departure. Complaint Hand detection system not operating correctly / vehicles with code 266 Fault message in instrument cluster: "Active Emergency Stop Assist not available" "Active Lane Keeping Assist not available" Cause Possible causes: the hand detection mat, the hand detection control unit, the contacts and the steering wheel harness.
• 11018039May 1, 2025Electrical system. Complaint Symptoms relating to CIVIC A26/17 - MBUX multimedia system + instrument cluster (head unit)] and/or displays Cause Enhanced technical support process for CIVIC modules and associated displays Remedy Note: Do not replace any components. For all symptoms concerning CIVIC and displays create a TIPS case after performing initial diagnosis.
• 11018032May 1, 2025Electrical system. Complaint In vehicles with the MBUX multimedia system Gen20x.i2 without premium sound system and external amplifier, the sound does not meet the customer's expectations. Changing the sound settings, for example for the bass, does not provide the desired effect. Cause Sound parameter software in the A26/17 - MBUX multimedia system + Instrument cluster (Head unit) control unit Remedy For vehicles with standard sound…
• 11017500Apr 28, 2025Exterior lighting. Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy Check for external damage: You can identify a damaged…
• 11017496Apr 28, 2025Exterior lighting. Complaint Headlamp, front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Remedy NOTE: If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Headlamp: Remedy 1 Clearing fogged/condensed LED headlamps and LED rear…
• 11017217Apr 21, 2025Visibility (wipers, defrost, mirrors). Complaint Random heating of air conditioning system. Cause Temperature sensor in overhead control panel (OCP) delivering incorrect values: The temperature sensor in the overhead control panel is malfunctioning. Fault code B110709 or fault code B11F697 are present in the overhead control panel with the status (active) or (active stored).
• 11017208Apr 21, 2025Electrical system, Exterior lighting. Complaint Message in instrument cluster "Adaptive high beams assistant not available/inoperative" or "DIGITAL LIGHT reduced range of functions" in relation to "FC151E29- The level sensor at front left has a malfunction. There is an invalid signal" in the control unit HLI/LED headlamp range adjustment front left. Cause Electronic interference occurring at the sensor level of the front axle. Remedy Update of the…
• 11017127Apr 21, 2025Seats, Electrical system. Complaint The "Easy entry and exit feature" function deactivates itself after a brief period. Cause The cause is currently being investigated. Remedy A remedy is currently not available. A software update in the seat control unit does not solve the problem. The document will be updated once the reason has been analyzed and a remedy is available.
• 11017037Apr 7, 2025Electrical system. Complaint Traffic sign symbol for "Traffic Sign Assist" is blinking in instrument cluster without obvious cause usually with one of the following scenarios: • Flashing without a speed limit ("- -"). • Flashing when current vehicle speed is under speed limit. • Flashing between US speed limit symbol and European speed limit symbol. Cause Under Investigation Remedy Under investigation. One option is to turn off…
• 11016221Mar 25, 2025Electrical system. Complaint This LI does Not apply to 223 or 206 which use a different generation of 48V systems. Please follow the relevant guided tests for the 223 and 206. For 223 with fault code B1FCB97 follow LI54.10-P-076026. Various causes are possible. The faults listed in the various causes do not all have to be present at all times. Some of these complaints may overlap. Rely on the faults listed in the Cause section for…
• 11015626Mar 13, 2025Electrical system, Transmission and drivetrain. Complaint - Engine diagnosis indicator lamp (MIL) lights up. - Current and saved fault code in DCCU and powertrain control unit (PTCU): P2E9873 The position sensor of the external socket flap of the vehicle socket (direct current) indicates an electrical fault. The actuator does not open. - The vehicle starts or charges normally and without any problems. Cause Software in the control unit "N116/5 - DC…
• 11015627Mar 10, 2025Electrical system, Exterior lighting. Complaint The luggage compartment lighting switches off and back on erratically if the tailgate is opened with the ignition switched off. Cause The problem was caused by a software error in the control unit N10/8 (Rear SAM). Remedy Software update to the control unit N10/8 (Rear SAM - Signal acquisition and actuation module rear control unit).
• 11015617Mar 10, 2025Electrical system, Body and structure. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead. This reduces the likelihood of the button…
• 11015614Mar 10, 2025Suspension. Complaint A squeaking noise comes from the electric power steering; see video with example. Cause Toothed rack in the area of the screw drive of the electric power steering needs additional grease. Remedy 1. Lift the vehicle and remove the center engine compartment lining; for basic data, see WIS AR61.20-P-1105S 2. Loosen the bellows of the electric power steering on the right of the steering gear and slide outward…
• 11015667Mar 8, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles. The software for the communication module does not correspond to the latest series production configuration. The communication module will receive an OTA update. The update is downloaded and installed in the background. During installation, the system can be used without restrictions. The new…
• 11015663Mar 7, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and…
• 11015659Mar 7, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the communication software does not correspond with the latest series production configuration. The communication module will receive an OTA update which includes quality-enhancing optimizations and improves the system stability and accessibility of Mercedes me services. The update is downloaded and…
• 11015543Mar 7, 2025Engine. Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901…
• 11015673Mar 5, 2025Electrical system. Issue Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain subject vehicles, the MBUX multimedia system software does not correspond with the latest series production configuration. The MBUX multimedia system software will receive an update to introduce new functions and improve the customer experience. Remedy MBUSA will conduct an OTA service campaign.
• 11015640Mar 5, 2025Electrical system. Complaint During a phone call, the called party has difficulty understanding/cannot understand the driver, or interference/background noises are audible to the called party during a call. It becomes increasingly difficult to understand as the speed rises. Cause A. Seating of the microphones in the headliner. Side edges are covered by the textile cover (see picture "1") B. Assembly of microphones (B25/20 or B25/21)…
• 11014686Feb 28, 2025Fuel system. Complaint Check engine light on. Engine in limp-home mode. Rough running. Low fuel rail pressure fault code P008700 stored in MRG2 control unit. Additional faults below may be stored in MRG2 control unit: Misfire- P030000, P030100, P030200, P030300, P030400, P030084, P030004 Mixture adaptation- P217800 P218762, P017100, P017200, P217700 Injector malfunction- P02EE00, P02EF00, P02F000, P02F100, P214601, P214901…
• 11014684Feb 28, 2025Engine. Complaint Red oil pressure warning in instrument cluster One of the below fault codes is stored in powertrain control unit N127: P052497 The oil pressure is too low. The system function is restricted. P052400 The oil pressure is too low Cause Various Remedy If low oil level warning present diagnose cause of this first. -Check engine oil level and correct if necessary.
• 11014610Feb 25, 2025Back-over prevention (rear camera), Electrical system. Complaint Please note that the exact quick test conditions must be met as seen below. If not exactly as listed below, there is no need to create a TIPS case referencing this LI unless further assistance is needed outside of this document.

← All problems reported for the 2024 Mercedes-Benz E350