2019 Mercedes-Benz GLE 400 Technical Service Bulletins

135 technical service bulletins (TSBs) are on record for the 2019 Mercedes-Benz GLE 400. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 11008070Sep 26, 2024Suspension. Complaint Creaking noise, in irregular sequence when driving slowly in combination with slight steering movements. Sound file attached for comparison. NOTE: Steering functionality is not affected. For 192 and 232: Only affects vehicles up to VIN vehicle identification end number. If vehicle falls outside of VIN range, create a TIPS case. Model series 192: xxx xxx xx 182881 Model series 232: xxx xxx xx 182883 Cause…
• 11007974Sep 21, 2024Exterior lighting. Complaint Headlamps leaking or fogged Cause The fogging of the headlamp is a natural phenomenon which can occur under certain climatic conditions. In contrast to a leaky headlamp, physical fogging does not result in a technical impairment of the headlamp. A leak test must be performed to determine if physical fogging exists or if the headlamp is leaky. Remedy In advance, observe LI82.10-P-078301 "Headlamps or Front…
• 11008323Sep 10, 2024Exterior lighting. Complaint Headlamps fogged or droplets forming. Cause Due to its outlet openings, the headlamp is an "open system". This means that acidic gases, moisture, dirt and exhaust gases can penetrate into the headlamp. This can lead to the formation of condensation on the lens of the headlamp. The headlamps comply with all applicable US standards and regulations. Remedy Check housing cover of lamp unit for natural fogging…
• 11007753Sep 10, 2024Exterior lighting. Complaint Headlamp or front fog lamp leaky or fogged Cause Fogging of the headlamps is a natural phenomenon, which can occur under certain climatic conditions. It does not lead to any technical impairment of the headlamp. Headlamps comply with all applicable standards. If a pressure compensation diaphragm is fitted in the housing cover, then the lamp unit is a "closed system". Remedy Headlamp: Remedy 1 Clearing…
• 11007790Sep 9, 2024Exterior lighting. Complaint Headlamps fogged or droplets forming. Cause Due to the housing cover with pressure compensation diaphragm, the headlamps are a "closed system". This means that the headlamps are protected against acid gases, dirt and exhaust gas. However, moisture can still enter from two sources. Through absorption and desorption (the commonest cause) or through permeation.
• 11007728Sep 9, 2024Transmission and drivetrain. Complaint To insure vehicle down time is kept at a minimum and all required information is available when case is escalated, as well as assist technicians with checks that may help lead in resolving issue without case creation. THIS LI IS NOT TO BE USED AS A REASON FOR CASE CREATION BUT AS A GUIDE IF A CASE IS NEEDED Cause There are, at times, additional steps workshops can do to help diagnose and rectify…
• 11005294Jul 23, 2024Exterior lighting. Complaint Rear lamps fogged up/not leaktight. Cause Fogging of the rear lamps is a natural phenomenon, which can occur under certain climatic conditions. This does not lead to any technical impairment of the rear lamps. Remedy Rear lamp: Remedy 1: Clearing fogged/condensed rear lamps: 1. Drive the vehicle into the workshop (temperature higher than +18 °C/+64.4 °F) Note: Do not wash the vehicle or subject it to…
• 11005344Jul 9, 2024Transmission and drivetrain. Complaint Customer complaints relating to automatic transmission 725.0 (NAG3 Classic / 9G-TRONIC automatic transmission) and 725.1 (NAG3 facelift/9G-TRONIC automatic transmission facelift) For faster, more effective and more targeted diagnosis, Intelligent Predictive Repair (IPR) has been developed and integrated into XENTRY Diagnosis. This ensures an automated diagnosis process.
• 11005331Jul 9, 2024Transmission and drivetrain. Complaint Only vehicles with a variable transfer case are affected. Can be identified through control unit N45 or N15/7 in the quick test When accelerating with light load, vibrations or jolting sensation may come from the drivetrain Cause Modified oil quality of the transfer case over time Remedy Check initial quick test for faults in the following control units N45 - All-wheel drive (ARS) N127 - 'Drivetrain'…
• 10253708Apr 30, 2024Electrical system. In our continuing efforts to assure the proper performance of Mercedes-Benz products and to enhance the satisfaction of our customers, Mercedes-Benz USA (MBUSA) is extending the coverage for the Fuel System Control Module (FSCM) software on your vehicle from the original New Vehicle Limited Warranty of 4 years / 50,000 miles to 1 S year: / 150,000 mile: (whichever occurs: first), and applies to the vehicle…
• 10249540Jan 29, 2024Electrical system. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2019-2023 A-Class, CLA, E-Class, G-Class, GLA, GLB, GLC, GLE, GLS, and S-Class (177, 118, 238, 463, 247, 253, 167, and 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration. The communication module system will receive an…
• 10249495Jan 24, 2024Steering. Noises in the steering column area when steering. Under analysis. Check which area of the steering column the noises occur in. Do the noises tend to occur at the bottom in the driver footwell or do they tend to occur in the area of the steering column switch module (MRSM/SCCM)? If the noises occur in the area of the MRSM/SCCM, work through the following points: - Loosen screws of the MRSM/SCCM and steering wheel…
• 10249482Jan 24, 2024Steering. The steering wheel generates grinding noises between the steering wheel and steering column switch module during steering maneuvers See example file in the attachments area: Lenkrad-Schleifgeräusch_SteeringWheel-GrindingNoises.mp4 The plastic cover on the back of the steering wheel is not positioned correctly and may therefore rub against the steering column switch module Please use the following noise files for…
• 10249726Jan 18, 2024Electrical system. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz, has determined that in certain MY 2017-2021 C-Class, CLA, CLS, E-Class, GLC, GLE, GLS, AMG GT, S-Class, SL, and SLC (205, 117, 257, 213/238, 253, 166/292, 190/290,217/222, 231, 172) vehicles, the software of the communication module does not correspond with the latest series production configuration.
• 10248195Dec 7, 2023Electrical system. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, C-Class, CLA, CLS, E-Class, EQB, G-Class, GLA, GLB, GLC, GLE, GLS, AMG GT, S-Class (177, 205, 118, 257, 213, 238, 243, 463, 247, 253, 167, 290, 217, 222 platform) vehicles, the communication module system software does not correspond with the latest series production configuration.
• 10248162Dec 4, 2023Seats. Crease formation on genuine leather seat covers in vehicles with low mileage • Objects left on the seats for extended periods of time (pressure marks). • Objects wedged between the seat backrest and seat cushion (e.g. seat belt buckle). • Light initial creases due to vehicle handling. • Light creases in the outer covers originating from the production process (missing finish). Heat treatment of…
• 10248203Dec 1, 2023Electrical system. Mercedes-Benz AG, the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY19-23 A-Class, CLA, CLS, E-Class, EQB, GLA, GLB, GLC, GLE, GLS, AMG GT (177, 118, 257, 213, 238, 243, 247, 253,167, 290 platform) vehicles, the head unit software does not correspond to the current series production configuration. The head unit will receive an OTA update to optimize the "Live Traffic Information" service…
• 10244837Oct 10, 2023Electrical system. The "SOS nonfunctional" message appears sporadically in the instrument cluster of the vehicle. The fault code B129C00 is stored in the control unit log. The message occurs in particular after the vehicle has been non-operational for an extended period of time; the message then disappears of its own accord after a few minutes. No functional limitation to the emergency call system is to be expected. Software error in…
• 10241527Aug 28, 2023Electrical system. Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vehicles, has determined that on certain MY 2018-2023 C-Class, EQE, EQE SUV, EQS, EQS SUV, GLC, GLE and S-Class (206, 295, 294, 297, 296, 254, 167 and 223 platform) vehicles, the communication module software does not correspond with the latest series production configuration. The update is free of charge and will be carried out in the background.
• 10241790Aug 18, 2023Electrical system, Equipment. The Mercedes me connect services cannot be activated. The remote status data does not update. Error in N112/9 - control unit for telematics services (HERMES). In the HERMES control unit log, under the "URL" tab, the value DEFAULT is stored for "atpServerUrl" and/or "rcsServerUrl". Please carry out a re-commissioning of the control unit N112/9 - Control unit for telematics services (HERMES), which includes both a…
• 10237252May 25, 2023Body and structure. Complaint Cracking and creaking noise from area of roof frame, C-pillar (inner) when driving on rough terrain. Cause Sheet metal sections in the area of the roof frame, C-pillar (inner) could cause noises due to tension or contact of the sheet metal. Remedy 1. Remove the headliner and detach the head airbag in the working area. 2. Park vehicle in the sun/heat and allow it to warm up. 3. Then perform a test drive…
• 10235676Apr 5, 2023Suspension. Check upper transverse control arm of front axle on left and right, replace upper transverse control arm if necessary
• 10235667Apr 4, 2023Electrical system. Complaint Ambient lighting malfunctions sporadically, mainly in the Ocean Blue color value and with animation "ON". After the next ignition cycle, the ambient lighting functions again correctly. Cause Software in coupling elements (EKE) faulty. The coupling element software cannot be updated in After-Sales. Remedy In a complaint case, replace the respective wiring harness (coupling elements are installed on the…
• 10233784Mar 1, 2023Steering. Complaint Knocking noises from area of steering gear, particularly when decelerating or accelerating. Cause - Remedy Please create a TIPS case with informative videos and send this to the responsible MPC.
• 10231025Jan 7, 2023Steering. Complaint No power steering available following engine start, warning message and indicator lamp "Steering" active in instrument cluster. Fault code P063500: "The electric power steering has a malfunction. _" in control unit N68 "Electric power steering" The fault code details show for "Root_Cause_ErrorID": 60015 - ECU reset occurred - No assist start-up was executed Cause Software error when starting the electric…
• 10231032Jan 5, 2023Latches, locks and linkages, Electrical system. Complaint Tailgate opens unintentionally. Cause Accidental or unnoticed activation of the button to open the tailgate on the vehicle key. E.g. when stored in trouser pocket, handbag etc. Remedy As of the 6th generation, the vehicle key can be recoded so that the tailgate no longer opens as a result of a long press on the button, but by double-clicking on the button instead.
• 10222475Sep 12, 2022Body and structure. Complaint Metallic noises from area of instrument panel Cause Due to a possible drop in torque at the screw connection of the NVH struts in the engine compartment (see picture in the attachment), noises may be perceived in the area of the instrument panel. Remedy Replacement of the 8 screws of the NVH struts in the engine compartment.
• 10222461Sep 12, 2022Steering. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle manufacturing date) 1. Replace repair kit for steering column height adjustment 2…
• 10222481Sep 8, 2022Electrical system. Complaint Customer states after a bus sleep the SiriusXM category changes from "My Favorites" to "All Stations" or a different category. Sometimes, the "My Favorites" category will be unavailable for the entire drive cycle. Cause Current MBUX Multimedia System (A26/17) software release Remedy Software update of MBUX Multimedia System (A26/17) to E905.4 (in development). This document will be…
• 10219260Aug 15, 2022Engine cooling. Complaint Yellow coolant warning system message appears in instrument cluster. Fault code P048392 or P048397 present in N127 Powertrain Control Unit. Cause Faulty communication between fan and control unit N127-PTCU. Remedy Replace engine fan with part as specified in XENTRY parts information. Group 50/015 part 400. Note: Do not install a lower wattage fan than what was originally installed in vehicle.
• 10219263Aug 1, 2022Seats. Complaint On vehicles with "ARTICO man-made leather upholstery" or "ARTICO man-made leather upholstery / DINAMICA microfiber - black (601A)" the material of the seat side bolster can tear. Both the seat cushion cover and the backrest cover on the front seat can be affected here. Cause The material may tear because the material in the side bolster is not suitable. Remedy Optimized seat covers are now available for…
• 10217157Jul 14, 2022Electrical system, Equipment, Steering. Complaint Height adjustment of electric steering column adjustment jammed in the top/bottom adjustment position (e.g. with Easy Entry function). Cause Height adjustment moves to the top/bottom limit stop and jams. 1. Steering column height adjustment transmission 2. Seat control unit software Remedy There are 2 repair procedures to follow depending on vehicle (differentiated according to model and vehicle…
• 10217158Jul 11, 2022Equipment, Steering. Complaint Noises from the area of the steering column. - Creaking - Squeaking - Chattering - Humming - Grinding Cause At present, there are no known noise problems with the steering column. Remedy Check surrounding area of the steering column for possible noises. - Instrument panel support - Steering column switch module If the cause of the noise can be narrowed down to the steering column, create a PTSS case
• 10217156Jul 11, 2022Equipment, Suspension. Complaint Malfunction due to the ingress of dirt during the repair of the hydraulic system. Cause Cleaning instructions in WIS are not being sufficiently observed. This can result in dirt entering the hydraulic system of the vehicle or the filling unit. In subsequent filling/emptying procedures, the dirt is then transferred to another vehicle.
• 10217163Jul 8, 2022Equipment, Electrical system. Complaint The Apple Carplay interface cannot be controlled via the center console touchpad or the right-hand steering wheel touchpad. Cause A setting on the iPhone may prevent control via the touchpad Remedy To remedy on the affected iPhone, navigate to "Settings" -> "Accessibility" -> "Touch" and turn the "BackTap" option OFF.
• 10213046May 9, 2022Suspension. Complaint Fault message, suspension, max. 50 mph in instrument cluster. "i" - Fault code "ERR_INF2_CORE2CORE_COMM_FAILURE" = true is stored in the quick test and/or current. Cause Communication fault between electrohydraulic suspension component parts through out-of-date software (application software and bootloader software).
• 10210925Apr 18, 2022Suspension. Cause Communication fault between electrohydraulic suspension component parts through out-of-date software (application software and bootloader software). Remedy With the latest hardware item number for the electrohydraulic pump units A167 901 62 03, the new application software A167 902 31 12 and the new bootloader software A167 904 18 01 have to be flashed. With older hardware item numbers, please open a PTSS case.
• 10210931Apr 13, 2022Electrical system, Seats. Complaint • Seats cannot be adjusted • Seats cannot be folded • Seats in the 2nd seat row cannot be locked or unlocked • Normalization cannot be performed in its entirety using XENTRY Cause Under analysis Remedy *Make sure a battery charger is connected to vehicle while performing all testing* Please perform the following checks that help to resolve most concerns: #1 - Make sure seat control units have…
• 10209877Mar 31, 2022Electrical system. Complaint The result from the XENTRY battery test does not match the current state of the battery. Cause The XENTRY battery tester uses the stored on-board electrical system data in the SAM module to access the health of the 12 volt battery. The XENTRY battery test may not take into account a single discharge event because the SAM cannot record the data if the battery is discharged. Note: A discharged battery does…
• 10207198Jan 27, 2022Electrical system. Complaint The garage door hand transmitter cannot be initialized with the integrated garage door opener in the inside rearview mirror. Cause 1. The integrated garage door opener (GDO) is not compatible with the opening system installed in the garage. 2. The garage door drive uses a rolling code system. In contrast to the fixed code system, the LED in the mirror in this case flashes green after programming. 3.
• 10207183Jan 4, 2022Equipment, Engine cooling. Complaint Sporadic warning message in instrument cluster "Engine oil pressure stop switch off vehicle" (or similar) is shown in red on vehicles with low mileage. Cause Directional control valve may stick. Remedy 1- Read off oil level in instrument cluster and correct if necessary. 2- Perform approx. 10-15 engine starts, then clear fault codes. 3- Perform road test with vehicle. If fault code reoccurs during road…
• 10206080Dec 17, 2021Engine cooling. The exhaust gas cleaning information label does not correspond to currently valid specifications. It is therefore possible that the emission classification given on the information label may not correspond to the certified classification. This issue has no impact on the vehicle's registration papers.
• 10206077Dec 8, 2021Engine cooling. "MY15+ M278 and M157 Equipped Vehicles with Fault Code ""P023400 – Boost Pressure is Too High"" "
• 10206067Dec 2, 2021Equipment, Electrical system. MBUX multimedia system: Map data does not match with your system/the navigation system cannot be activated
• 10206063Dec 1, 2021Electrical system. "Functional impairment of 48 V on-board electrical system "
• 10205835Sep 16, 2021Other or unknown, Back-over prevention (rear camera), Body and structure. Model series 167 noise on B/C/D pillars.
• 10205806Aug 30, 2021Equipment. Upon selecting navigation, the central display may show the following message: "Map data does not match with your system. Please insert a medium containing the corresponding map data". the navigation menu cannot be opened.
• 10205812Aug 27, 2021Equipment. The customer may note that the Dashcam feature is inoperable with one of the following complaints.
• 10205814Aug 11, 2021Fuel system. Fuel filler flap opens slowly/switch flashes/tank is bleeding instrument cluster warning
• 10205794Aug 11, 2021Body and structure, Visibility (wipers, defrost, mirrors). Excessive resistance of door side windows when being raised/lowered, cracking and squeaking noises.

← All problems reported for the 2019 Mercedes-Benz GLE 400