2015 MINI Cooper Technical Service Bulletins

395 technical service bulletins (TSBs) are on record for the 2015 MINI Cooper. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10148442Nov 1, 2014Equipment, Suspension. Noise from Front Axle Control Arm Hydraulic Bearing. When driving in high ambient temperatures on rough road surfaces, at speeds between 5 and 30 mph, a squeaking noise may be heard coming from the front axle. Hydraulic bearing of the front axle control arm
• 10148441Nov 1, 2014Engine, Electrical system, Equipment. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. The sealing plug was not tightened sufficiently during production.
• 10149400Oct 1, 2014Equipment. Delivery Stop: Head Airbag.A Delivery Stop has been issued on certain F56 vehicles produced from August 8, 2014 through August 14, 2014. These vehicles will need both head airbags replaced. Affected vehicles in dealer inventory must not be retailed or delivered until this issue is corrected. Vehicles at ports of entry will be repaired prior to dealer delivery. This bulletin will be updated with instructions and…
• 10149399Oct 1, 2014Engine cooling. Start/Stop Button Must Be Pressed Several Times to Stop Engine. To turn the engine off when it is running, the Start/Stop button must be pressed several times. This error does not affect starting the engine. Body Domain Controller (BDC) application software error. BDC fault "8040A9 - Start-stop button SST: Incorrect operation (pushed at an angle)" is stored.
• 10149397Oct 1, 2014Brakes. Front Axle Brake Pad Wear Sensor Routing.During brake service, the brake pad wear sensor cable may be incorrectly routed and also fastened to the front brake caliper?s bleed valve dust cap. Incorrect routing of the brake sensor cable may cause damage to the cable or brake sensor, resulting in a brake warning message being displayed.
• 10057572Oct 1, 2014Electrical system. Mini: the start/stop button needs to be touched several times before the engine can be turned off after running. Starting engine is not affected. Possible software application error. Model f56.
• 10148058Sep 1, 2014Electrical system, Visibility (wipers, defrost, mirrors). Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
• 10148057Sep 1, 2014Engine, Electrical system. "The Service Engine Soon (MIL) On with Fault 102001: Air Mass Too High. The Service Engine Soon light (MIL) is illuminated with the Check Control message: ""Drivetrain: Drive Moderately"" displayed. Fault 102001: Air mass too high is stored in the DME. CAUSE Unfavorable DME software"
• 10148056Sep 1, 2014Transmission and drivetrain, Electrical system. "VANOS Control Faults Stored Due To DME Error. The Service Engine Soon (MIL) lamp is illuminated, and the engine could go into a reduced power mode with the ""Drivetrain Malfunction"" message displayed. One or more of the VANOS faults listed in the attachment are stored in the DME, although the engine is mechanically sound and no unusual noises can be heard from the VANOS area.
• 10148054Sep 1, 2014Engine. Service Action: Program Control Units (DME). Due to unfavorable DME software, the engine idle speed may be unstable and fluctuate at times.
• 10148052Sep 1, 2014Equipment. "MINI ""AMP-up"" Motorer Care Fleet Increases. MINI USA, a division of BMW of North America, LLC (""MIN USA""), is pleased to introduce the Aftersales Mobility Program (AMP) Motorer Care Fleet Increase. The ""AMP-up"" program is designed to support (on a temporary basis) your alternate transportation needs, even in challenging times.
• 10148051Sep 1, 2014Equipment. "?Incorrect Vehicle Identification Number (VIN) Labels Installed. Twenty-six ""Model Year 2014"" vehicles have incorrect VIN labeling that indicates they are ""Model Year 2015."" Incorrect VIN labels were applied at the factory. The 9th and 10th digits of the VIN indicate that it is a MY 15 (F), when in reality the vehicle is a MY 14 (E). This includes the NHTSA compliance label, VIN number in the windshield and…
• 10148393Aug 1, 2014Steering, Engine, Electrical system. Power-assisted Steering Intermittently Not Available at Engine Start-up. An EPS warning lamp may light up in the instrument cluster intermittently at engine start-up. At the same time, the power-assisted steering is unavailable. After switching the ignition off and then on again, the steering is available again. No fault codes are stored in the fault code memory of the electric power steering (EPS-I1). Electric…
• 10148392Aug 1, 2014Equipment, Steering. Knocking Noise from Front of Vehicle when Turning. While driving or with the vehicle stationary, a knocking or popping noise can be heard from the front of the vehicle when turning the steering wheel to the full locked position in either direction. Screw connection between the swivel bearing and control arm.
• 10148391Aug 1, 2014Engine. N16 Engine: Oil Leak from Cylinder Head Sealing Plug. An oil leak can develop at a sealing plug located in the cylinder head, just below the vacuum pump. CAUSE The sealing plug was not tightened sufficiently during production.
• 10056794Aug 1, 2014Steering. Mini: there is noise, popping or knocking, heard from front of vehicle, when driving or stationary, and turning steering wheel to lock position and is caused by screw that is connected between control arm and swivel bearing. Model f56 hardtop.
• 10148153Jul 1, 2014Visibility (wipers, defrost, mirrors). Washer Fluid Leaks from Front Washer Jets. When operating the rear window washer, washer fluid leaks from the front windshield washer nozzles. Design issue with the windshield washer system
• 10148152Jul 1, 2014Visibility (wipers, defrost, mirrors). Squeaking Noise When Operating Front Windshield Wiper. A squeaking noise can be heard when operating the front windshield wiper. Fitment between the cowl panels and the left windshield wiper post
• 10148151Jul 1, 2014Transmission and drivetrain. Service Action: Manual Gear Shift Knob Loose. The manual transmission gear shift knob easily comes off the shift rod with minimal upward force.
• 10148150Jul 1, 2014Engine cooling. Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon"…
• 10148149Jul 1, 2014Engine cooling. Service Action: Retrofit of the Engine Coolant Temperature Sensor. Internal corrosion could form in the engine coolant temperature sensor which is integrated into the thermostat housing (not replaceable). This corrosion leads to internal bridging of the contacts, which can cause an inaccurate engine temperature reading. This false reading could lead to difficulty in the engine starting or a "Service Engine Soon"…
• 10148148Jul 1, 2014Fuel system, Electrical system. Various Check Control Messages with Fault 11B033 Stored in DME. A drivetrain or MSA malfunction Check Control message may be displayed, along with a Service Engine Soon light (MIL). DME fault 11B033: Fuel pump control module (FPC), signal: Short circuit to ground is stored in the DME. CAUSE Unfavorable DME software diagnostics
• 10148147Jul 1, 2014Transmission and drivetrain. B38M Shuts Off when Placed into Gear After Cold Engine Start. After a cold start, the engine idles poorly and could shut off when the transmission in placed into Reverse or Drive position. Unfavorable DME software.
• 10148146Jul 1, 2014Engine cooling. At operating temperature, the engine idle speed could dip low. In rare cases, the engine may stall, requiring a restart. This could mostly likely occur at a low speed (2nd gear) when coasting off the throttle and slowing to a stop. This situation could be perceived as an MSA malfunction: intermittent and not easily reproduced. Unfavorable DME software.
• 10148145Jul 1, 2014Engine. ?Service Engine Soon Lamp (MIL) On with DME Fault 120408 Stored. The Service Engine Soon lamp (MIL) is illuminated with a reduction of engine power. Fault 120408: Charging pressure control: Switch-off, pressure build-up blocked is stored in the DME. CAUSE 1. This fault normally sets as the result of a problem with another component of the engine management system. 2.
• 10148244Jun 1, 2014Equipment, Visibility (wipers, defrost, mirrors). Front Windshield Washer Jets Not Working. When operating the windshield washer, very little or no washer fluid is coming out of the washer jets. The windshield washer hose shown below is too short. This causes it to kink or disconnect.
• 10148242Jun 1, 2014Suspension. Delivery Stop/Service Action: Shock Absorber Rear Axle MODEL F56 (MINI Hardtop) SITUATION A rear shock absorber with a malfunctioning damper valve may have been fitted into some vehicles. Important note: In the group of identified vehicles, only four shock absorbers in total are affected. The damper function of these four units is only partially effective. These four shock absorbers can be identified, based on a…
• 10148359May 1, 2014Equipment, Wheels. Service Action: Replace Wheel Bolt Wrench. The internal thread of the wheel bolt wrench is incorrect at M8. AFFECTED VEHICLES This Service Action involves F56 vehicles according to VIN selection. First check if a Service Action label with a code number 64 is already attached to the B-pillar. If a code number 64 has been punched out, the Campaign has already been performed and no further action is necessary.
• 10148358May 1, 2014Equipment. Automatic Deactivation of Recirculation Mode. The customer states the recirculation display goes out, even though the recirculation button was switched on. CAUSE The automatic recirculation air deactivation feature was introduced in July 2012. Note: If the customer dislikes this feature, it can be deactivated by using the following steps.
• 10148357May 1, 2014Electrical system, Exterior lighting. LED Headlight Malfunction Displayed, but Lights Function Properly. A check control message or warning light is on, indicating a headlight malfunction, but the lights operate correctly. The BDC (Body Domain Controller) fault code 8041B6: "Headlight (LWR): System failed" is the only fault stored. This fault can occur after QC1 is performed or after a vehicle software update. BDC (Body Domain Controller) software error
• 10148356May 1, 2014Equipment, Electrical system. Vehicle Honks for 20 Seconds when Left in Neutral. INFORMATION This is normal vehicle operation if the customer leaves the vehicle (with the key in pocket) in Neutral without being shifted into Park. The honking noise notifies the customer that if the shifter is not put into Park position, the vehicle will roll away or, if left alone for longer periods, have a discharged battery. Please refer to the attached…
• 10148355May 1, 2014Visibility (wipers, defrost, mirrors), Equipment. Washer Fluid Leaks from Front Washer Jets. When operating the rear window washer, washer fluid leaks from the front windshield washer nozzles. Design issue with the windshield washer system
• 10148353May 1, 2014Body and structure. F56 Make Good Program: Install Accessory Roof Graphic or Mirror Caps. Due to production restrictions at Plant Oxford, certain F56 vehicles produced in May and June of this year cannot be built with the factory option for the contrasting roof and/or mirror caps. This production issue was caused by the plant expanding its paint capabilities to meet increasing vehicle demand.
• 10148352May 1, 2014Body and structure. Driver's Side Exterior Door Handle Cover Cap Is Loose. The driver's side exterior door handle cover cap is loose or missing. CAUSE Driver's side exterior door handle
• 10148351May 1, 2014Visibility (wipers, defrost, mirrors), Equipment. Transportation Protective Sleeve Introduced for Windshield Wipers. The windshield wipers streak and judder. The windshield wiper blades become distorted during transportation and when in storage.
• 10148350May 1, 2014Tires. Erroneous Check Control Message: Tire Pressure Check Failed. After pressing the Start/Stop button, Check Control message "Tire pressure check failed" appears briefly, as well as the corresponding light in the instrument cluster. These displays disappear after a few seconds. Software in the BDC (Body Domain Controller)
• 10148349May 1, 2014Brakes, Electrical system. Erroneous "Service due" Message Although Brake Lining Thickness is Above Minimum Specification. The yellow "Service Due" warning message lights up in the instrument cluster, even though the brake pad thickness is more than 4.2mm (above the thickness at which the pad sensor intervenes). The calculated remaining service life for the brake pads (front and/or rear axle) from the CBS data does not match the actual brake…
• 10148348May 1, 2014Engine cooling. Turbocharger Coolant Pump: Fault Code 20A503. "Drive Faulty" message is displayed in the Check Control. Fault code 20A503 "Turbocharger coolant pump, self diagnosis: Signal implausible" is stored in the DME. Unfavorable DME software application
• 10148346May 1, 2014Engine cooling. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2…
• 10148345May 1, 2014Equipment, Engine. B38 and B48 Engines: Engine Oil Pressure Faults Stored in DME Memory. INFORMATION When diagnosing the vehicle, the following fault is stored in the DME: FC 1C0102 Engine Oil Pressure control, plausibility, static: pressure too low If the vehicle's integration level is not F056-14-11-500 or higher, and no other faults related to the engine oil pump or engine oil pressure regulating valve are stored in the DME, it…
• 10148299Apr 1, 2014Exterior lighting. After deleting transport mode during PDI (QCI Pre-Delivery Inspection), fault code ?8041A9 - Daytime running light lock active? is present in the BDC (Body Domain Controller) and the DRL (Day Running Light) is switched off. CAUSE Software in the BDC.
• 10148296Apr 1, 2014Electrical system, Engine. Service Action: Grease Engine Starter Electrical Terminals. Due to the location of the engine starter, the electrical contacts must be coated with special contact grease for protection from moisture and outside elements.
• 10148295Apr 1, 2014Engine, Equipment. B38 and B48 Engines: Grease Residue Found at Bottom of Transmission Bell Housing. INFORMATION While performing repairs to the underside of the vehicle, the technician may notice yellow grease residue has formed on the lowest point of the transmission bell housing near the engine starter. The residue is not related to the engine oil or transmission fluid. The grease was applied to the starter during vehicle…
• 10148294Apr 1, 2014Engine cooling, Equipment. "Delivery Stop/Service Action:Replace Oil Filter Housing Assembly. A Delivery Stop has been issued on certain 2014 model year F56 vehicles produced from November 2013 to March 2014. A coolant leak could occur at the oil filter housing, resulting in overheating, loss of power and an engine warning light. Affected vehicles in dealer inventory must not be retailed or delivered until the oil filter assembly has been…
• 10147958Jan 1, 2014Engine, Electrical system. N16: Fault 274D Mixture Adaptation Is Stored in the DME. Certain low speed, light-load driving conditions at lower outside temperatures could cause the Service Engine Soon lamp (MIL) to illuminate. The following fault would be stored in the DME: ??Fault 274D: Mixture adaptation, lower engine speed range (mixture too lean) CAUSE 1. Possible intake/exhaust leaks, or a faulty component as listed in the test plan 2…

← All problems reported for the 2015 MINI Cooper