2009 Nissan Rogue Technical Service Bulletins

98 technical service bulletins (TSBs) are on record for the 2009 Nissan Rogue. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10192615Aug 6, 2015Transmission and drivetrain. SERVICE INFORMATION The information in this bulletin is provided to help ensure correct diagnosis and repair of fluid leaks. All fluid leaks, when properly diagnosed, should be repaired (whether under warranty or customer pay) to ensure proper vehicle operation. However, certain normal operating conditions can be misdiagnosed as a leak requiring repair.
• 10192597Jul 6, 2015Equipment, Back-over prevention (rear camera), Steering, Brakes, Wheels. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty.
• 10192591Jun 24, 2015Engine cooling. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for…
• 10192532Mar 11, 2015Equipment. SERVICE INFORMATION NOTE - Failure to follow the procedures in this bulletin may result in the denial of a warranty claim. In an effort to protect the paint finish, Paint Guard Film (PGF) is applied on many new Nissan vehicles. Paint Guard Film is a temporary white plastic protective film that is applied by the factory to the horizontal painted surfaces of the vehicle.
• 10192513Jan 16, 2015Air bags, Equipment, Back-over prevention (rear camera). SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition.
• 10192474Nov 20, 2014Electrical system, Transmission and drivetrain. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit…
• 10056480Oct 7, 2014Engine cooling. Nissan: see document search button for owner letter. On certain vehicles, a voluntary emission recall campaign is being conducted and the engine control module (ecm) will be reprogrammed. Model 2008-2010 rogue.
• 10054516Aug 15, 2014Engine. Nissan: some vehicles may experience reduced performance caused by the cvt fluid temperature protection logic. *js updated 4/18/14. *pe updated 9/29/14.
• 10192394Jun 24, 2014Equipment, Electrical system. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this…
• 10192348Apr 9, 2014Electrical system. IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
• 10055490Apr 9, 2014Electrical system. Nissan: the main harness to body harness connectors is experiencing electrical corrosion issues. 2008-2014 rogue.
• 10192335Mar 20, 2014Equipment, Engine cooling. IF YOU CONFIRM A rattle coming from the exhaust center tube heat shield, and a heat shield spot weld is detached, ACTION Install a band clamp around the heat shield and over the detached spot weld. See this bulletin for further detail.
• 10192305Jan 27, 2014Equipment, Air bags. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail.
• 10192293Jan 13, 2014Engine, Engine cooling. SERVICE INFORMATION Replacement Engine Control Modules (ECMs) for many newer Nissan vehicles are now "Blank" ECMs. Blank ECMs come without software and must be programmed (not reprogrammed) before they will function. See this bulletin for further detail.
• 10032306Nov 27, 2013Exterior lighting. Nissan: exterior lamp fogging. Occasionally water is noticed in the exterior lamps. This is generally not due to a defect. All current exterior lamp assemblies are vented to the atmosphere (not sealed). This is necessary to allow for expansion and contraction of air from temperature variations (warmer or colder) without damage to the lamp. Moisture in the air sometimes travels into and out of the lamp assembly…
• 10192266Nov 15, 2013Fuel system, Equipment. SERVICE INFORMATION If one or more of these EVAP leak DTCs are stored (P0442, P0455, P0456) on a 2007 through 2011 Nissan vehicle, a loose fuel fill cap may be the cause. Use the following resources to perform diagnostics and confirm the cause of stored DTCs. ASIST: - Appropriate Service Manual diagnostic procedures - Applicable Technical Service Bulletins (TSB). Leak Test: - With CONSULT-III plus - WORK SUPPORT >>…
• 10053956Nov 15, 2013Fuel system. Nissan: a loose fuel fill cap is the cause of evap leak dtcs (p0442, p0455, p0456) stored on some vehicles. Model years 2007-2011. Model not listed.
• 10192233Aug 27, 2013Equipment, Wheels. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming…
• 10192231Aug 26, 2013Electrical system. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details.
• 10192217Jul 23, 2013Brakes, Steering, Wheels. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical…
• 10192216Jul 23, 2013Wheels, Brakes, Steering, Suspension. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the…
• 10192192Jun 7, 2013Electrical system. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer…
• 10192158Apr 4, 2013Electrical system. SERVICE INFORMATION Improper adjustment or operation of the ASCD brake switch can cause the Automatic Speed Control Device (ASCD) to "not set" and/or DTC P0605 (ECM) to store. See this bulletin for further detail.
• 10051768Apr 4, 2013Vehicle speed control. Nissan: cruise control will not set and dtc p0605 is stored.
• 10192155Apr 3, 2013Vehicle speed control, Seat belts. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled…
• 10051767Apr 3, 2013Latches, locks and linkages. Nissan: lock/unlock request button on outside handle does not respond.
• 10192145Mar 19, 2013Suspension. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod…
• 10192127Feb 15, 2013Body and structure. SERVICE INFORMATION If a CD/DVD Player incident is noted, a possible cause may be improper CD/DVD disc care, condition, or usage. This bulletin provides updated CD/DVD Player operation instructions to avoid potential incidents/customer concerns caused by improper care and usage of CD/DVD discs. To aid in solving customer concerns, use the guidelines in this bulletin when speaking to customers or inspecting incident…
• 10192120Feb 1, 2013Equipment. IF YOU CONFIRM Oil is leaking from the upper end of the engine oil cooler. ACTION: Reseal the oil cooler with the parts listed in the PARTS INFORMATION on page 2. - For repairs, refer to REPAIR PROCEDURE starting on page 3. NOTE: Do not replace the complete engine oil cooler assembly for this incident, if it should occur. See this bulletin for further detail.
• 10192114Jan 25, 2013Equipment. SERVICE INFORMATION A new updated front brake rotor service part is available for the Applied Vehicles in this bulletin. See this bulletin for further detail.
• 10192068Nov 14, 2012Engine cooling. SERVICE INFORMATION The R&I (Remove and Install) procedure on an applied vehicle for blower motor service will be amended to include the knee bracket. If a blower motor is to be removed and reinstalled or replaced, add the step shown in this bulletin. - The procedure for blower motor R&I is in the I VENTILATION, HEATER & AIR CONDITIONER>VTL Ventilation System section of all related ESMs. See this bulletin for…
• 10046601Sep 25, 2012Brakes. Nissan: bulletin regarding diagnosis of abs/vdc wheel speed sensor. Model 2007-2013 nissan.
• 10047059Aug 27, 2012Visibility (wipers, defrost, mirrors). Nissan: rain sensors may operate, intermittently or unexpectedly, when exhaust gas, moisture, fingerprints, dirt, or insects are near or around rain sensors. No models or model years listed.
• 10044570Jul 6, 2012Transmission and drivetrain. Nissan: if continuously variable transmission (cvt) fluid temperature rises above a certain threshold, it will go into fluid protection logic mode (fail safe mode), as designed.
• 10044039May 18, 2012Engine cooling. Nissan: if for any reason the engine harness is replaced, during the replacement of the harness, install a rubber protective pad on the battery tray support bracket. *js updated 5/24/2012
• 10043950Apr 10, 2012Transmission and drivetrain. Nissan: ecm replacement procedures with consult iii plus. Applies to all 2004 and later (does not apply to leaf/ev) vehicles.
• 10043735Feb 3, 2012Other or unknown, Latches, locks and linkages. Nissan: door lock/unlock inoperative with intelligent key.
• 10041392Sep 6, 2011Engine cooling. Nissan: oil is leaking from the upper end of the engine oil cooler.
• 10027865May 16, 2011Fuel system, Other or unknown. Nissan: fuel gauge does not read full, or slow to respond. Fuel level gauge is inaccurate or reads erratically. For 2wd model replace fuel sender. For awd replace the fuel sender and sub-sender unit. *pe updated 6/24/11.
• 10040032Oct 28, 2010Body and structure. Nissan service campaign: see document search button for owner letter. Recall to apply a seal and special grease to help prevent the front outside door handle latch assembly from freezing. 2008-2009 rogue.
• 10031305Sep 30, 2010Tires. Nissan: tire pressure monitoring system (tpms) warning light on/flashing. No models or model years listed. *pe updated on 08-11-2011.
• 10032506Sep 13, 2010Equipment. Nissan: vent control valve replacement. When replacing the evap canister vent control valve for reason: use the one listed on page 2; for vent control valve replacement procedure, refer to the appropriate section of the electronic service manuals (esm; when installing the new valve, do not add any lube to its o ring; for frontier (d40 series) only, install the protector listed in parts information. *pe includes…
• 10032992Apr 27, 2010Exterior lighting. Nissan: xenon head lamp service. A xenon headlamp is not functioning because of an issue inside the headlamp assembly (an internal issue). In most cases, replacement of a bulb or hid control unit will solve the incident. This includes all models with xenon head lamps. No models listed.
• 10033125Feb 25, 2010Equipment. Nissan: grinding/knocking noise from rear when turning. There is a grinding or knocking noise or vibration from the rear of the vehicle-when making wide turns; on dry roads; at low speeds (under 20mph). *pe updated 11/02/11.
• 10033308Feb 10, 2010Electrical system. Nissan: dtc p0444 (evap canister purge volume control solenoid valve circuit open is stored).
• 10038567Dec 11, 2009Transmission and drivetrain. Nissan service campaign: see document search button for owner letter. There is a subtle rattle noise that is coming from the transmission at low speeds. 2008-2009 rogue.
• 10032509Nov 5, 2009Tires. Nissan service campaign: see document search button for owner letter. Wheel valve stem nut. Some model year 2008-2009 vehicles may have been built with tire pressure monitor system (tpms) transmitter nuts that were not manufactured to specification. Over time, these nuts may corrode and potentially crack, especially in areas where heavy concentrations of road salt are used.
• 10030165Apr 6, 2009Electrical system. Nissan: the 12 volt battery is an important part of the vehicle electrical system and is required to stay connected when the engine is running. To prevent damage to vehicle electronic components follow the instructions/cautions. No model years listed.

← All problems reported for the 2009 Nissan Rogue