2015 Subaru WRX Technical Service Bulletins

417 technical service bulletins (TSBs) are on record for the 2015 Subaru WRX. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10171084Jan 10, 2020Electrical system, Equipment. The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.
• 10169881Dec 13, 2019Equipment, Electrical system. This bulletin announces availability of a new HVAC blower motor unit assemblies developed to address isolated concerns of the blower motor becoming inoperative. If this issues occurs on models with Auto A/C, the blower fan may become totally inoperative. If this issue occurs on models with Manual A/C, the blower fan may operate on high speed only. The root cause of these conditions is water intrusion into the…
• 10169868Dec 9, 2019Seats. This bulletin announces a change made to the leather front seat cushion covers to address isolated concerns of a sagging/loose fitting condition after an occupant leaves the seat as shown in the example photos below. A pattern revision was made to increase tension of the cover material and decrease the time it takes for the condition to disappear after an occupant leaves the seat.
• 10168585Nov 6, 2019Electrical system, Engine cooling. "This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below."
• 10165497Sep 26, 2019Transmission and drivetrain. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified likely sources of the seepage to be the sealant used on the CVT’s oil pump chain cover and the input shaft oil seal. The repair involves chain cover removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the…
• 10165512Sep 20, 2019Engine cooling. The purpose of this Bulletin is to provide procedures for the diagnosis and repair of oil seepage which may be coming from the timing chain cover, front camshaft cap, camshaft carrier and / or upper oil pan. There are five areas that should be closely inspected if an oil leak is reported by the customer: 1. The 6mm tapped hole casting boss area in the left-hand camshaft cap 2. The sealing surfaces between either…
• 10164447Aug 29, 2019Body and structure. This Service Information Bulletin announces a design change made to the rear bumper cover side mounting brackets. These new brackets provide increased clearance between the edges of the bumper cover and the corresponding quarter panels. This change will prevent them from contacting each other and possibly damaging their painted surfaces.
• 10164446Aug 29, 2019Transmission and drivetrain. "This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified likely sources of the seepage to be the sealant used on the CVT’s oil pump chain cover and the input shaft oil seal. The repair involves chain cover removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing…
• 10164392Aug 23, 2019Equipment, Electrical system. This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Claims Policies and Procedures Manual found in subarunet.
• 10164182Aug 5, 2019Electrical system, Engine cooling. This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: “ECM/PCM ENGINE OFF TIMER PERFORMANCE”. Under certain RARE conditions, an electrostatic surge may influence the ECM’s internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from…
• 10163563Jul 30, 2019Electrical system. This bulletin announces availability of a new Engine Control Module (ECM) for the models listed above designed to address DTC P2610: “ECM/PCM ENGINE OFF TIMER PERFORMANCE”. Under certain RARE conditions, an electrostatic surge may influence the ECM’s internal timer used after the engine is turned off and store a DTC P2610 in memory. Hardware in the ECM has been changed to eliminate any impact from…
• 10163558Jul 26, 2019Electrical system, Equipment. All 2015-2017 MY vehicles with Fujitsu TEN (F10) 7in. Multimedia Navigation (AVN) & Display Audio Units. This bulletin provides information to help diagnose and address different conditions relating to customer concerns which may arise when operating the new-generation “Gen 2” and “Gen 2.1” F10 Navigation and Display Audio systems. We will continue to add more helpful tips to this TSB as they become…
• 10163530Jul 16, 2019Electronic stability control, Brakes. This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driver’s side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
• 10163526Jul 12, 2019Visibility (wipers, defrost, mirrors), Electrical system. "This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: • Power windows inoperative from the driver’s door master and / or passenger front door switch • Unable to remotely operate other door windows from the driver’s door master switch • One-Touch Auto Up / Down features inoperative from either / both front door switches"
• 10163525Jul 11, 2019Brakes. This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the…
• 10163520Jul 9, 2019Exterior lighting, Electrical system. SOA has received multiple requests for additional 83399Fj000rt BRAKE LIGHT SWITCH tools and now has sufficient stock to allow retailers to place orders for single tools.
• 10163017Jun 27, 2019Engine. This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
• 10161831May 28, 2019Equipment, Body and structure. This Service Information bulletin announces a design change made to the TGV assemblies used on the Forester Turbo models and WRXs listed above. Condensation resulting from EGR system operation may enter the area between the TGV shaft and bearing. Over time, corrosion can develop and impede movement of the TGV shaft and cause any of the DTCs P2004, 2005, 2006 and /or P2007 to set. The material of the TGV shaft has…
• 10161824May 21, 2019Equipment. Subaru Service and Technical Support Line Newletter.
• 10161822May 15, 2019Equipment. This Service Information bulletin announces a design change made to the retaining bolt used to secure the child anchors to the rear shelf plates on the models listed above. This change was made in support of parts communization with other similar mounting bolts. There is no change between the old and new bolt in terms of function or durability.
• 10161813May 6, 2019Equipment. To help reduce confusion and increase technician efficiency, Subaru of America, Inc. (SOA) has developed the following cross reference list to help locate the appropriate Special Service Tool.
• 10161812May 2, 2019Visibility (wipers, defrost, mirrors), Electrical system. This bulletin announces availability of new power window switch assemblies developed to address the following customer concerns: ? Power windows inoperative from the driver?s door master and / or passenger front door switch ? Unable to remotely operate other door windows from the driver?s door master switch ? One-Touch Auto Up / Down features inoperative from either / both front door switches
• 10161811May 2, 2019Steering. This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) gear box (steering rack) assembly. The repair (when applicable) involves installation of a new tension spring for the worm gear to reduce / eliminate the condition.
• 10160214Apr 23, 2019Electrical system, Engine. This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
• 10160211Apr 17, 2019Electrical system, Exterior lighting. This bulletin provides a procedure for replacing the rear combination lamp wiring harness. The harness is now available as a service part separate from the lamp assembly.
• 10160490Mar 8, 2019Engine cooling, Equipment. This Service Information bulletin provides new inspection and repair procedures for AVCS (Active Valve Control System) -related DTCs on the FA and FB engine equipped models listed above. The applicable Service Manuals will be revised with this new information in the near future.
• 10160485Mar 4, 2019Equipment. This bulletin provides a procedure to follow for addressing customer concerns of a shuddering condition or chattering -type sound heard or felt when making sharp turns. If an applicable vehicle presents with the condition as described, it is recommended to perform the transfer clutch break-in procedure as described.
• 10155225Feb 22, 2019Equipment. This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
• 10155220Feb 20, 2019Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components.
• 10154425Jan 31, 2019Engine, Equipment. The purpose of this bulletin is to announce a change to the specification of the valve springs used in the FB engine. The new springs have different color paint marks to help identify their application.
• 10154423Jan 29, 2019Electrical system. This Service Information bulletin announces availability of a new control valve assembly (valve body) designed to prevent false detection of DTC P0841 and / or illumination of the AT Temp light. Testing has revealed in some limited cases, air bubbles (aerated fluid) may enter certain pressure circuits within the control valve assembly causing fluid pressure control and adjustment to be calculated incorrectly…
• 10154419Jan 25, 2019Brakes. This Service Information bulletin announces instruction for application of additional lubrication between the brake caliper support and pad clips. This will prevent the pad from dragging due to corrosion buildup which may result in uneven or premature wear of the replacement brake pads. This additional instruction applies to all models with brake pads using the upper and lower pad clips and has been added to the…
• 10154417Jan 24, 2019Electrical system. This bulletin announces a design change made to the engine wiring harness to improve resistance to moisture. A detailed illustration describing the change is supplied below.
• 10154207Jan 10, 2019Equipment, Air bags. This Bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system.
• 10154206Jan 8, 2019Transmission and drivetrain. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT?s oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the cover.
• 10153187Nov 14, 2018Engine. This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333. The knock sensor for DIT engines is now utilized for NA engines to improve durability and resistance to heat.
• 10153178Nov 6, 2018Transmission and drivetrain, Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components.
• 10150949Oct 26, 2018Transmission and drivetrain, Equipment. This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate.
• 10150924Oct 26, 2018Transmission and drivetrain, Equipment. This Service Information bulletin announces a design change to the clutch release bearing used on the models as listed above. During assembly of the bearing, a different type of grease is used which has a higher resistance to heat. In cases where the operator keeps a foot on the clutch pedal for extended periods, an increased amount of heat is generated which can cause the grease inside the bearing to deteriorate.
• 10150946Oct 22, 2018Transmission and drivetrain, Equipment. This bulletin announces a change to the clutch system components optimizing their durability and resistance to certain severe driving conditions including high-temperature operation.
• 10150921Oct 22, 2018Transmission and drivetrain, Equipment. This bulletin announces a change to the clutch system components optimizing their durability and resistance to certain severe driving conditions including high-temperature operation.
• 10150936Oct 12, 2018Brakes. This Service Information bulletin announces a design change made to the front brake rotors used on the models listed above. The change makes it easier to identify these parts from those used on other models.
• 10150911Oct 12, 2018Brakes. This Service Information bulletin announces a design change made to the front brake rotors used on the models listed above. The change makes it easier to identify these parts from those used on other models.
• 10150932Oct 9, 2018Latches, locks and linkages, Body and structure. This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just…
• 10150887Oct 9, 2018Electrical system, Body and structure. This bulletin provides a service procedure to address a gap between the top edge of the door and the instrument panel on the models listed as shown in the photo below. The gap may also make the glove box door difficult to close fully.There is a latch to keep the glove box closed on both sides of the glove box door. If the door is closed without using enough force to engage both latches or by pushing it shut on just…
• 10146486Sep 27, 2018Equipment. A design change was made to the blower motor assembly to address the following customer concerns: ? Blower fan is either inoperative or only operates on high speed. ? Excessive rotational-type sound heard when the fan is operating.
• 10146485Sep 24, 2018Electrical system. This bulletin announces a new Vehicle Dynamics Control (VDC) Module and Hydraulic Control Unit (VDCCM&HCU). The new part was designed to address a small number of customer concerns regarding a clicking or ticking-type sound heard coming from the driver?s side footrest area. The new modules incorporate logic with enhanced internal solenoid and motor control characteristics.
• 10146480Sep 18, 2018Exterior lighting. This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
• 10145078Aug 29, 2018Transmission and drivetrain. This Service Information bulletin announces a design change made to the rubber timing hole access plug to improve its retention and prevent water intrusion into the converter case.
• 10144875Aug 9, 2018Exterior lighting. This bulletin outlines a design change made to the inner lens extension portion of the LED headlamp assembly. Under the right conditions, the shape of the lens for the actual head lamp light source can cause sunlight to be focused onto the extension portion of the lens resulting in deformation. A heatresistant shade has been added to protect the affected area.

← All problems reported for the 2015 Subaru WRX