2015 Subaru WRX Technical Service Bulletins

417 technical service bulletins (TSBs) are on record for the 2015 Subaru WRX. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10143878Jul 28, 2018Visibility (wipers, defrost, mirrors). This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets.
• 10143873Jul 23, 2018Electrical system. This bulletin announces a design change to the EPB adapter cord harness connector. In some cases, the retaining tab of the connector may become damaged as a result of removal or installation for diagnosis and later and cause DTC C1956 or C1957 to set and the brake warning lamp to illuminate. The retaining tab portion of the connector has been changed to improve its durability and prevent recurrence of the DTC.
• 10142838Jun 21, 2018Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components.
• 10142831Jun 6, 2018Body and structure. This bulletin replaces TSB 12-201-16R and provides a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop?s rear corners may come in contact with the hood panel and abrade the finish.
• 10142830Jun 6, 2018Body and structure. IMPORTANT: This Service Bulletin has been as been replaced by TSB 12-243-18 dated 6/6/2018 entitled ?Paint Chipping between Hood Grille (Scoop) and Hood?. Please refer to this new bulletin for the latest information regarding this condition.
• 10141490May 31, 2018Brakes. This Service Information bulletin announces availability of a new front brake pad shim kit to specifically address customer concerns of a squeaking or squealing sound on the models listed. The new shims incorporate a new laminated design with increased damping characteristics to eliminate vibration identified as the root cause of the sound. The new kits include shims only (NO brake pads).
• 10141499May 10, 2018Equipment. This bulletin announces a design change to the A/C Condenser receiver-dryer assembly. The change involves the addition of a rubber end cap and retaining clip onto the bottom of the receiver-dryer tank portion to prevent corrosion intrusion and enhance sealing.
• 10141496May 10, 2018Equipment, Body and structure. 4 DOOR MODELS ONLY. This bulletin announces a change made to the trunk lid lock (latch) assembly. The purpose of this change is to improve parts integration (or ?commonality?) between models. This change is not intended to address any specific customer concern.
• 10141495May 3, 2018Body and structure, Equipment. This bulletin announces a design change to the front door checkers used on the models listed. The new checker mechanism provides a more ?positive feel? of the detents or check positions as the front doors are opened and closed.
• 10133522Mar 28, 2018Visibility (wipers, defrost, mirrors). This bulletin provides a repair procedure for replacing the foam cushion installed between the top front edge of the IP and the windshield glass. Use the supplied Service Procedure to address a customer concern involving the foam cushion becoming visible above the IP near the defroster vent outlets
• 10133521Mar 28, 2018Electrical system. On Forester Turbo and applicable WRX models, after re-connecting the battery, if the ignition switch is turned back ?ON? within one minute after the first time the ignition is turned ?OFF?, it becomes possible for the CEL to illuminate storing DTC P0606 in memory. The code will not occur immediately, but may occur after a period of time depending upon how the vehicle is operated
• 10133528Mar 23, 2018Electrical system. This bulletin announces a design change to the CVT select lever (shifter) mechanism in response to isolated customer concerns of not being able to remove the key from the ignition switch when the vehicle is in Park. The cause is contamination of the Park-Range switch internal components
• 10133520Mar 14, 2018Equipment. This Service Information bulletin provides a new troubleshooting chart to use when diagnosing a DTC B1760 related to the Occupant Detection System (ODS). Following these diagnostic steps will help avoid unnecessary ODS sensor / seat cushion assembly replacement
• 10133527Mar 13, 2018Transmission and drivetrain. 2010-15 Legacy/ Outback 2.5L NA CVT, 2015 Legacy/ Outback 3.6L NA CVT, 2012-15 Impreza 2.0L NA CVT, 2013-15 Crosstrek 2.0L NA CVT, 2014-15 Crosstrek Hybrid CVT 2014-15 Forester 2.5L NA CVT 2014-15 Forester 2.0L Turbo CVT 2015 WRX 2.0L Turbo models only. In the interest of customer satisfaction, Subaru of America, Inc.
• 10133529Mar 2, 2018Equipment. The purpose of this bulletin is to provide a description of current changes to Service Manuals available via the Subaru Technical Information System (STIS) web site. The tables contained within this bulletin are to be used as guides for becoming aware of the latest changes.
• 10140485Feb 13, 2018Equipment, Body and structure. This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to…
• 10140470Feb 13, 2018Body and structure, Equipment. This bulletin announces a design change to the air vent grille located in the lower portion of the trunk (or cargo) area. The shutters of the vent grille are designed to open briefly and relieve cabin pressure when the doors are shut with the windows fully closed. The vent grilles have rubber ?shutters? which occasionally, may catch on the frame (case) portion and not close properly allowing outside air / odor to…
• 10140483Feb 9, 2018Engine. 2.0L Turbor Models only. This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333.
• 10140468Feb 9, 2018Engine, Electrical system. 2.0L Turbor Models only. This Service Information Bulletin announces design changes to the engine?s knock sensor which will help improve vehicle assembly line efficiency and increase durability. In some cases, the Check Engine light may illuminate and a knock sensor-related DTC set in the ECM memory: P0327, P0328, P0332 and P0333.
• 10140480Feb 6, 2018Engine cooling, Equipment. 2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrence of ice formation from condensation in the duct?s PCV system passages.
• 10140425Feb 6, 2018Engine cooling. 2.0L Turbo Models only. This bulletin announces availability of a special turbocharger air intake duct designed to prevent EXTREMELY RARE occurrences of ice formation from condensation in the duct?s PCV system passages.
• 10130270Jan 24, 2018Brakes, Exterior lighting. This Service Information bulletin provides a measurement and adjustment procedure for the stop lamp switch. An improperly adjusted (or faulty) stop lamp switch can cause any of the DTCs listed above to set and result in the related system?s warning lamp to illuminate.
• 10130277Jan 11, 2018Body and structure. ( 2017-2018MY Impreza - 5 Dr Only)
• 10138778Dec 15, 2017Electrical system, Air bags, Equipment. NOTE: The Airbag systems used on previous and current WRX, STI and Tribeca models are NOT equipped with EDR functionality. This Bulletin provides information regarding Event Data Recorder (EDR) functionality which has been incorporated into the airbag system. The function of the EDR is best explained using the following statements found in the vehicle Owner?s Manual: ?This vehicle is equipped with an event data…
• 10125885Nov 9, 2017Equipment, Transmission and drivetrain. CVT MODELS ONLY. In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first).
• 10131689Oct 31, 2017Electrical system. This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: ? Check Engine light coming on (with DTC P05A0 stored in memory). ? Potential battery discharge (dead battery) after repeated periods of short-trip driving. ? A high (or ?hanging?) engine RPM after depressing the clutch pedal (Forester only).
• 10131664Oct 5, 2017Steering. This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) rack assembly. The repair involves installation of a new tension spring for the worm gear to reduce / eliminate the condition. It should be noted the condition is NOT detrimental to the operation of the EPS system.
• 10131629Sep 22, 2017Steering. This bulletin provides a service procedure to address isolated customer concerns of a rattling sound identified as coming from the Electronic Power Steering (EPS) rack assembly. The repair involves installation of a new tension spring for the worm gear to reduce / eliminate the condition. It should be noted the condition is NOT detrimental to the operation of the EPS system.
• 10131632Sep 11, 2017Engine cooling. This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs.
• 10117554Aug 16, 2017Equipment. This bulletin contains illustrations of exchange components and their manufacturer as well as a description of the proper exchange procedure. The exchange program policy can also be found in Sections 8.4.9 and 11.2.10 of your Claims Policies and Procedures Manual found in subarunet.
• 10117558Aug 14, 2017Electrical system, Transmission and drivetrain. 2.0L DIT Models Only. Subaru of America, Inc. has determined that vehicles affected by this Service Program require ECM reprogramming. This bulletin includes the service procedure for diagnosis and repair of customer concerns involving engine idle roughness or, in some cases, engine noise and/or damage resulting from spark knock (pre-ignition). The Engine Control Module logic has also been optimized requiring the…
• 10117543Aug 8, 2017Electrical system. This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: * Check Engine light coming on (with DTC P05A0 stored in memory). * Potential battery discharge (dead battery) after repeated periods of short-trip driving. * A high (or "hanging") engine RPM after depressing the clutch pedal (Forester only).
• 10117528Jun 26, 2017Engine cooling. This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the…
• 10117535Jun 23, 2017Electrical system. This bulletin announces the availability of reprogramming files to optimize the ECM and address the following customer concerns: * Check Engine light coming on (with DTC P05A0 stored in memory). * Potential battery discharge (dead battery) after repeated periods of short-trip driving. * A high (or "hanging") engine RPM after depressing the clutch pedal (Forester only).
• 10117538Jun 21, 2017Transmission and drivetrain, Equipment. CVT MODELS ONLY. In the interest of customer satisfaction, Subaru of America, Inc. (SOA) is extending the New Car Limited Powertrain Warranty coverage for the Continuously Variable Transmission (CVT) on the above listed models and model years from the original five (5) years or sixty thousand (60,000) miles (whichever comes first) to ten (10) years or one-hundred thousand (100,000) miles (whichever comes first).
• 10117529Jun 15, 2017Engine, Engine cooling. This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound.
• 10111087Apr 20, 2017Latches, locks and linkages, Body and structure. This new bulletin replaces TSB 12-186-15 and announces a new repair procedure to address customer concerns of the hood scoop scrubbing the finish of the hood panel in the areas shown in the photo below. Due to different expansion rates between the metal hood panel and the resin material used for the hood scoop, the edges of the scoop's rear corners may come in contact with the hood panel and abrade the finish.
• 10111086Apr 20, 2017Transmission and drivetrain. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT's oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the cover.
• 10111074Mar 10, 2017Engine cooling. This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage.
• 10131692Feb 23, 2017Electrical system. This bulletin announces the availability of reprogramming files to optimize the ECM and address isolated customer concerns of a spark knock (engine ping) -type sound.
• 10131698Feb 16, 2017Seats. This bulletin announces a design change made to the front seat outer hinge cover trim panels. In some cases, when exiting the vehicle, the trim panel may inadvertently get kicked and become dislodged from the seat cushion assembly. The shape of the front portion of the panel has been changed to prevent this condition.
• 10131699Feb 15, 2017Fuel system. REVISED. This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
• 10131703Feb 5, 2017Electrical system. This bulletin announces availability of reprogramming files for optimization of the transmission control module (TCM). The new logic addresses customer concerns of inconsistent shifting characteristics and / or a ?slipping? -type sensation which may be experienced under moderate acceleration after a cold start before the CVT is up to operating temperature.
• 10111071Dec 30, 2016Fuel system. This bulletin announces a design change of the fuel injector used on 2.0L DIT models to prevent water intrusion. A new silicone rubber cover has been developed and incorporated into production for this purpose.
• 10111069Dec 27, 2016Engine cooling. This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability
• 10111067Dec 16, 2016Fuel system. This Service Information bulletin announces a change to the shape of the rubber cap used on the flange nuts securing the sub-level sending unit to the fuel tank. In addition, two of the caps are now used in production instead of only one. This change was made to enhance productivity during vehicle assembly.
• 10111066Dec 14, 2016Transmission and drivetrain. Only Models Equipped with TR690 CVT only. This bulletin has been developed in response to a small number of customer concerns regarding fluid seepage found coming from the CVT assembly. Investigation has identified a likely source of the seepage to be the sealant used on the CVT's oil pump chain cover. The repair involves removal, a thorough cleaning and inspection of the sealing surfaces followed by re-sealing the…
• 10120999Nov 29, 2016Electrical system, Equipment. All 2012 to 2015 Models Equipped with Fujitsu Ten (F10) Generation 1 (Gen1) Audio / Navigation Systems. This bulletin announces a new procedure for updating the operating software used in F10 Gen1 audio / navigation systems. This new procedure eliminates the need to exchange the head unit / SD card to obtain software-related updates and operating enhancements.
• 10121003Nov 21, 2016Equipment. IMPORTANT NOTE: Due to the extensive revisions made to the information originally contained in this bulletin, a new bulletin, 15-205-16 has been issued. Please refer to this new bulletin for the latest information regarding this condition.
• 10120997Nov 16, 2016Equipment. The purpose of this bulletin is to provide replacement key and immobilizer information along with an overview of the Subaru Lock Information web-site.

← All problems reported for the 2015 Subaru WRX