2013 BMW 535I Technical Service Bulletins

399 technical service bulletins (TSBs) are on record for the 2013 BMW 535I. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10147715Jun 1, 2015Suspension. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
• 10147447Jun 1, 2015Engine cooling. Service Action: Replace the Thermostat. The Service Engine Soon light is on with corresponding fault codes in the DME for the engine thermostat.
• 10147155May 1, 2015Latches, locks and linkages, Electrical system, Body and structure. Trunk Lid Does Not Operate with Remote After Programming. If the customer profile is assigned to only unlock the driver door after programming with ISTA/P 3.55.x, the trunk will not open with the remote. CAUSE Coding error in CAS (Car Access System) for trunk locking
• 10147154May 1, 2015Equipment. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147143May 1, 2015Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can occur. The check control message (ID…
• 10147136May 1, 2015Tires, Wheels. Valve Stem Replacement with Wheel Electronics. INFORMATION The valve stems are single-use only, and must be replaced every time the wheel electronics are replaced. If you loosen the nut (1), you must replace the valve stem. Failure to replace the valve stem will lead to a pressure leak. The proper repair procedure can be found in REP 3611533. Not applicable. [ Copyright (c)2015 BMW of North America, Inc.
• 10147135May 1, 2015Body and structure, Suspension. Groaning Noise from Front Axle. Groaning noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers) or over uneven road surfaces. CAUSE Hydraulic mount in tension strut
• 10147131May 1, 2015Fuel system. Service Action: N63 Replace High-Pressure Fuel Pumps. The high-pressure pump may fail, resulting in an engine malfunction warning and reduced engine output.
• 10147130May 1, 2015Electrical system. ?SI B12 21 14May 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated April 2015. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show…
• 10147127May 1, 2015Engine. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10147125May 1, 2015Engine. N63 Engine: Valve Seal Replacement. Refer to the following applicable SIBs before replacing the valve seals. ? B11 07 11 - Turbocharger Failure: Oil Supply and Return Line Blockage and Proper Repairs ? B11 07 12 - N63 Engine: Oil Consumption and/or Rough Running Complaints ? B11 01 13 - N63 Engine: Engine Oil Consumption, Engine Oil Top-ups and Refill Capacity ?
• 10193495Apr 6, 2015Visibility (wipers, defrost, mirrors). The customer complains of rattling noises from the rear window when driving on rough roads.
• 10157983Apr 1, 2015Suspension. Service Action: Replace Left Rear Air Spring. Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.
• 10156210Apr 1, 2015Suspension. Service Action: Replace Left Rear Air Spring. Torsional stress can cause the threaded fabric of the left air spring bellow to rupture and lose its airtightness. If the air spring is not airtight, the vehicle will lean on one side.
• 10152317Apr 1, 2015Back-over prevention (rear camera). Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear…
• 10152309Apr 1, 2015Electrical system. Service Action: Program Control Units (SCR). The Selective Catalyst Reduction (SCR) control module can make an error when calculating the DEF line pressure. This could cause the Service Engine Soon light (MIL) to come on with a pressure plausibility fault stored in the SCR module.
• 10152306Apr 1, 2015Fuel system. "N20 and N26 Engines: ETK Injector Part Number Error. INFORMATION The current version of ETK has an error on screen 13_1417: ""High -pressure pump/Tubing."" When selecting the high-pressure pump, the screen states ""only in conjunction with injector."" Disregard this statement and only replace the high-pressure pump.
• 10152305Apr 1, 2015Electrical system. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ?
• 10152301Apr 1, 2015Equipment. "This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel economy without compromising on its ""class leading"" power and performance.
• 10147690Mar 1, 2015Equipment. One or both of the situations listed below may be encountered: ? Android device connection stability (dropped calls) ? Third-Party App Metadata: The album art and song title do not update when streaming audio from Pandora or Spotify, etc. New KISU (Customer Initiated Software Update) software is available on the TIS website. This software improves the Bluetooth functionality in our vehicles, and it helps to keep us…
• 10147656Mar 1, 2015Engine. "This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT mandatory Technical Campaigns or Recalls. They should be completed only based on parts availability, workshop capacity, and the customer's schedule.
• 10147655Mar 1, 2015Engine. "N63: Quality Control Monitoring After CCP. INFORMATION If the vehicle exhibits any of the above drivability issues, perform the ISTA/D N63 Misfire Detection test plan. Please make sure the FASTA data is transmitted. Submit a PuMA case titled ""N63: Drivability after CCP."" Follow the recommendations received."
• 10147653Mar 1, 2015Engine. "N20 and N55 Engine: Engine Oil Filter Application for Plastic Oil Filter Housing. The current version of EPC does not provide all available options for the engine oil filters used in the N20 and N55 engines produced with a ""plastic"" oil filter housing. The illustration below will help identify the proper engine oil filter application until the EPC is corrected."
• 10147652Mar 1, 2015Engine. N20 and N26 Engine: Oil Leaks from Cylinder Head Cover. There is an engine oil leakage under the vehicle, or the vehicle smells of engine oil. The cylinder head cover gasket is leaking engine oil due to loose retaining bolt(s).
• 10147091Feb 1, 2015Air bags. "Airbag Warning Light: ACSM FC 930A60 or 930A1C Seat Occupancy Detection. According to the customer, the airbag warning light was on, but it may not be on when the vehicle arrives in the workshop. 1. ACSM fault code ""930A60 - Seat occupancy detection, front passenger; malfunction"" is stored. The fault may or may not currently be present. Or 2. ACSM fault code ""930A1C - Seat occupancy detection, front passenger…
• 10147085Feb 1, 2015Electrical system. "SI B61 30 14February 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated January 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the…
• 10147084Feb 1, 2015Transmission and drivetrain, Electrical system. Check Control Messages Related to Battery Charge During Cold Ambient Temperatures. On cold days with an outside ambient temperature of less than 15°F, customers may notice a check control message related to the battery that is displayed on the instrument cluster and the control information display. Under these conditions, the vehicle starts. Various power management faults can be stored. When the outside…
• 10147079Feb 1, 2015Wheels. SUBJECT Wheel Speed Sensor Faults Cannot Be Cleared. The Dynamic Stability Control (DSC) warning light comes on while driving. The following DSC fault codes for the wheel speed sensors are stored: ? 480712 and/or ? 480715 and/or ? 480718 and/or ? 48071B They cannot be cleared, even though the wheel speed sensors work correctly and no problem can be found with the wiring harness.
• 10147077Feb 1, 2015Transmission and drivetrain, Electrical system. SI B27 02 13February 2015 Intermediate and Special Transmission Technical Service This Service Information bulletin supersedes SI B27 02 13 dated June 2013. designates changes to this revision SUBJECT Knocking Noise from Driveline During Low-speed Turning. A cracking or knocking noise is heard from the driveline on sharp turns at low driving speeds (<15 mph). CAUSE Software calibration error in the transfer case…
• 10147073Feb 1, 2015Engine, Electrical system. SI B12 21 14February 2015 Engine Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B12 21 14 dated December 2014. designates changes to this revision SUBJECT Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not…
• 10147068Feb 1, 2015Engine. "This Service Information bulletin and attachment supersedes SI B11 16 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Check the Timing Chain. INFORMATION This bulletin outlines the procedure for checking the engine timing chains for wear, and should be completed in conjunction with SI B11 06 14, ""N63 Customer Care Package."" The N63CCP and N63 Engine Check the Timing Chain are NOT…
• 10147628Jan 1, 2015Equipment. "MSUBJECT iPhone and iOS 8.x Information. INFORMATION With the release of iOS 8.0, please be aware of the important functional change noted below: Scenario: z The customer leaves the vehicle and turns the phone off. z He or she turns the phone back on. z The customer then enters the vehicle, but does not unlock the phone prior to turning the vehicle on.
• 10147626Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 24 13 dated January 2014. designates changes to this revision SUBJECT Headunit-High: INITIAL Enabling Code Is Not Accepted Via I-Drive. INFORMATION Do not replace parts and do not program the vehicle for this issue. First-time activation of the navigation system should always be performed during the Quality Certification 1 (QC1) Pre-Delivery Inspection (PDI), with…
• 10147625Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 13 12 dated September 2012. designates changes to this revision SUBJECT Headunit High: Navigation System Road Map Usage. INFORMATION The Headunit High (HU-H), also called NBT, began replacing the Car Information Computer (CIC) on certain MY2013 vehicles with option 609. This change will affect the navigation system road map data support process and the warranty…
• 10147624Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 10 09 dated March 2013. designates changes to this revision SUBJECT CIC head unit: Vehicle Position Is Missing or Incorrect on Navigation Map. The vehicle position is missing or incorrect on the navigation map. The navigation system integrated in the Car Information Computer (CIC) is not calibrated correctly.
• 10147623Jan 1, 2015Equipment. This Service Information bulletin supersedes SI B65 05 09 dated July 2009. designates changes to this revision SUBJECT CIC Headunit: Navigation System Road Map Usage. INFORMATION The Car Information Computer (CIC) began replacing the Car Communication Computer (CCC) on vehicles with option 609 in September of 2008. This change affected the navigation system road map data support process and the warranty spare parts…
• 10147612Jan 1, 2015Brakes. "SUBJECT Carbon Ceramic Brake Noise. INFORMATION ""M"" vehicles are designed for high-performance, spirited driving. To accommodate this type of driving profile, a braking system which exceeds the standards for handling heavy brake forces, extreme temperatures, and excellent stopping power at high speeds is required.
• 10147603Jan 1, 2015Engine. SUBJECT N55: Engine Briefly Shudders or Runs Erratically After Cold Start. Under certain cold starting conditions, the engine may shudder or run a bit erratically for the first few moments when starting off. This can be felt at an engine speed of approximately 1,500 rpm. No relevant faults are stored in the DME memory. DME software calibration
• 10147602Jan 1, 2015Engine, Fuel system. SUBJECT N20, N26, and N55 Engines with Injector Electrical Faults. Any of the following symptoms could occur simultaneously with injector electrical faults stored in the DME: z After the engine is turned off for a short time, it can no longer be started; however, the starter motor turns. z The engine starts but immediately cuts off. z The engine runs erratically or lacks power. z The Service Engine Soon light (MIL)…
• 10147599Jan 1, 2015Vehicle speed control. "SUBJECT N55: Slight Surging at Constant Speeds when Accelerating Very Lightly. The vehicle shudders or surges slightly while driving at constant speeds and applying the accelerator very lightly. This symptom is most easily reproduced under light loads when the current fuel consumption is approximately 3448 miles per gallon.
• 10147595Jan 1, 2015Engine, Electrical system. SUBJECT DME Internal and Valvetronic Faults Set at Cold Ambient Temperatures. The Service Engine Soon light (MIL) can be illuminated with the erroneous internal and Valvetronic faults stored in the DME. The MIL will only come on if the fault has been detected on two (or more) consecutive drive cycles.
• 10147594Jan 1, 2015Transmission and drivetrain. SUBJECT N20 and N26 Differential Pressure Sensor Fault 195002 Stored in DME. The Service Engine Soon (MIL) light is on with the following differential pressure sensor fault stored: z 195002 - Differential pressure sensor, tank vent valve, electrical: Short circuit to ground During engine operation, vibration and movement of the sensor can damage the pin contacts of the harness connector, or cause a break in the…
• 10147593Jan 1, 2015Equipment, Engine. "This Service Information bulletin and attachment supersedes SI B11 06 14 dated January 2015. designates changes to this revision SUBJECT N63 Engine: Customer Care Package. INFORMATION This bulletin outlines the Customer Care Package program that has been designed exclusively for BMW vehicles with the N63 engine. Vehicles with the N63 high performance engine are engineered with EfficientDynamics that provides fuel…
• 10147591Jan 1, 2015Engine cooling. SUBJECT Deleting DME Adaptations After Crankshaft Sensor-related Repairs. The erroneous misfire faults are stored, and the Service Engine Soon light (MIL) illuminates The ISTA Service Function to delete the DME adaptations fails to clear the crankshaft incremental wheel adaptation, depending on the current DME software version. This adaptation must be cleared whenever the following repairs are made: 1. Replacement…
• 10148195Dec 1, 2014Equipment, Electrical system. Service Action: Bluetooth Software (KISU Data) Update. This Service Action is being released to improve customer satisfaction as we strive to be number 1 in the JD Power Initial Quality Survey (IQS). This new KISU software improves the Bluetooth functionality in our vehicles, and it helps keep us up-to-date with technology innovation. Please implement the Bluetooth Software Update Service Action. This Service…
• 10148194Dec 1, 2014Equipment, Electrical system. iPhone 6, 6 Plus, 5, 5S, 5C, 4S, 4, and 3GS with iOS 8.x Information. INFORMATION There is one major difference in functionality since iOS 8.0 was released. Scenario: z The customer leaves the vehicle and turns his or her phone off. z He or she turns the phone back on. z He or she enters the vehicle, but does not unlock the phone and start driving. Result: z The phone reconnects to the Bluetooth system (normal). z…
• 10148192Dec 1, 2014Equipment, Electrical system. Automated Activation of Navigation System During PDI/QC1. INFORMATION Important: The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department! When the vehicle is connected to the diagnostic system ISTA to perform PDI/QC1, the step to activate the navigation system (part of Delete Transport Mode) will automatically request the INITIAL NAV enabling code (VIN-specific) without…
• 10148186Dec 1, 2014Equipment, Electrical system. The Controller Responds Slowly or Not at All. When the customer presses or turns the controller, there is no or a delayed response. This can sporadically occur. Software in the controller
• 10148184Dec 1, 2014Electrical system, Equipment. BMW Maintenance Program: 12-Volt Battery Replacement Measure.
• 10148181Dec 1, 2014Brakes. M5 and M6 Front Axle Brake Squeak with Compound Brake System. A squeaking noise can be heard when braking from a slow speed. This situation may apply to M5 and M6 vehicles fitted with the metallic brake pads (P/N 34 11 2 284 869). These pads can be identified by the absorber weights at the top and bottom. Due to the design of the fixed caliper brake system, an unfavorable interaction between components may cause a…

← All problems reported for the 2013 BMW 535I