2020 BMW X3 Technical Service Bulletins

286 technical service bulletins (TSBs) are on record for the 2020 BMW X3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10184573Nov 1, 2020Engine cooling, Equipment. CONNECTING ROD BEARING: BMW AG has issued a Delivery Stop (effective November 20, 2020) on a small number of Model Year 2020-2021 BMW vehicles that were produced between May 15, 2019 and October 23, 2020.
• 10182910Oct 1, 2020Equipment. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated, with faults stored related to the upper and/or lower active air flap(s). Potential causes include: Faulty upper air flap actuator or flap assembly (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02…
• 10182908Oct 1, 2020Steering. INCREASED STEERING EFFORT WITH CHECK CONTROL MESSAGE (CCM): During multiple vehicle steering maneuvering or extended time at steering end stops (i.e. "full lock"), the check control message (CCM) "Increased steering effort, drive moderately" (CCM ID 997) may appear.
• 10182898Oct 1, 2020Body and structure. FRONT GRILLE UPPER/LOWER ACTIVE AIR FLAPS: LTD WTY EXT TO 15 YEARS/150,000 MILES: Component-Specific Limited Warranty Extension This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
• 10182611Oct 1, 2020Body and structure, Electrical system, Equipment. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated, with faults stored related to the upper and/or lower active air flap(s). Potential causes include: Faulty upper air flap actuator or flap assembly (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02…
• 10182609Oct 1, 2020Equipment, Steering. INCREASED STEERING EFFORT WITH CHECK CONTROL MESSAGE (CCM): During multiple vehicle steering maneuvering or extended time at steering end stops (i.e. "full lock"), the check control message (CCM) "Increased steering effort, drive moderately" (CCM ID 997) may appear.
• 10182605Oct 1, 2020Body and structure. FRONT GRILLE UPPER/LOWER ACTIVE AIR FLAPS: LTD WTY EXT TO 15 YEARS/150,000 MILES: Component-Specific Limited Warranty Extension This component-specific limited warranty extension applies to defects in materials or workmanship. This coverage is subject to the same vehicle eligibility requirements, limitations, and exclusions that apply to the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks.
• 10181226Sep 1, 2020Body and structure. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated.
• 10179824Aug 1, 2020Electrical system. COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery.
• 10179821Aug 1, 2020Electrical system. HEAD UNIT RESETS WHEN NAVIGATION IS USED IN CERTAIN LOCATIONS: The head unit resets sporadically causing the CID to turn black and then starts up again after a short time with the message "Start navigation system". This only occurs during navigation guidance when the "3D building" function is used Software in the Head Unit High (HU-H3).
• 10179820Aug 1, 2020Electrical system. INSTRUMENT CLUSTER DISPLAY SHAKES-SHIFTS TO THE LEFT: The Instrument cluster intermittently flickers, shakes and has shifted to the left. The fault is resolved once the vehicle goes into sleep mode.
• 10179819Aug 1, 2020Electrical system. DELIVERY STOP - HIGH-VOLTAGE BATTERY: Please do not charge the vehicle high-voltage battery until further notice. There may be a potential issue in the welding process of the HV-modules.
• 10179816Aug 1, 2020Latches, locks and linkages. DOORS WILL NOT COMPLETELY LATCH: One or more doors will not completely latch or will open to the first stage at times. The door lock strikers may be misadjusted.
• 10179811Aug 1, 2020Electrical system. EME GROUND CONNECTION MONITORING FAULTS: Check Control message (CCM ID 794): "Drive. Check as soon as possible" illuminates. Increased ground cable contact resistance at Electrical Machine Electronics (EME) due to corrosion/oxidation.
• 10179748Aug 1, 2020Equipment, Electrical system. NEW ECU VALIDATION NEEDED AFTER REPLACING CERTAIN CONTROL MODULES: With introduction of the new Headunit HU-H3 (MGU Media Graphics Unit), there is a new protection mechanism against tampering.
• 10179010Jul 1, 2020Electrical system. BMW CONNECTEDDRIVE APPS ARE NO LONGER AVAILABLE AFTER PROGRAMMING: After programming vehicle with "20-03" software, BMW ConnecedDrive apps are no longer available in the head unit. Software in the Head Unit High (HU-H3).
• 10179009Jul 1, 2020Electrical system. NAVIGATION SYSTEM - REPORTING MISSING OR INCORRECT ROADMAP DATA: Do not replace parts and do not program the vehicle. Roads can change by up to 15% every year. To ensure the best navigation experience, we do everything in our power to create the best maps. Your reports help us to detect changes in your area and keep future versions of our maps as accurate as possible. Therefore, a road map error or missing data…
• 10179007Jul 1, 2020Equipment. INSTRUMENT CLUSTER AND ONBOARD COMPUTER INTERMITTENTLY INOPERATIVE: The audio source, radio station, or music track cannot be changed using the MFL. Normal functionality may possibly return after a sleep cycle or a battery reset. This affects vehicles with: Integration level S18A-18-11-5xx Live Cockpit Professional (option code 6U3) including the instrument cluster High 4.1. While the Kombi is not working properly…
• 10179003Jul 1, 2020Electrical system, Equipment. VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
• 10178998Jul 1, 2020Electrical system. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: Potential causes include: Faulty upper air flap actuator (G01, G02, G12, G30, G32) Faulty lower air flap assembly (G01, G02, G12, G30, G32) Software error in the DME affecting the upper flap (G01, G02 only).
• 10178996Jul 1, 2020Brakes, Wheels. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: Ticking noise coming from front wheel while cornering without brakes applied, noticeable at low speeds. The vehicle must be moving.
• 10177632Jun 1, 2020Visibility (wipers, defrost, mirrors), Back-over prevention (rear camera). TOP VIEW CAMERA: IMAGE IS MISALIGNED: The top view image of the vehicle is misaligned when observed in the Control Information Display (CID). When the vehicle is parked in a parking spot with line markings, it is clearly noticed in the CID that the lines are not parallel to the side of the vehicle. This may be noticed on either the driver side, passenger side or both. Side view camera loose fitment in the exterior…
• 10177628Jun 1, 2020Electrical system. VEHICLE DOES NOT START BATTERY TOTALLY DISCHARGED: The customer's vehicle does not start due to a totally discharged battery.
• 10177627Jun 1, 2020Electrical system. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated, with faults stored related to the upper and/or lower active air flap(s).
• 10176382May 1, 2020Electrical system. SURROUND VIEW VEHICLE IMAGE DISPLAYED IS INACCURATE: When Surround View is activated the vehicle image displayed in the Central Information Display (CID) contains inaccurate details.
• 10176380May 1, 2020Electrical system. SURROUND VIEW WRONG VEHICLE DISPLAYED AFTER PROGRAMMING: After programming the wrong vehicle model is displayed in the Central Information Display (CID) when the Surround View is activated.
• 10176377May 1, 2020Electrical system. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: A yellow CCM (Check Control Message) ID 415 is displayed- "Increased battery drain! // Battery. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases…
• 10176376May 1, 2020Equipment, Visibility (wipers, defrost, mirrors). SUNROOF WATER LEAK DIAGNOSIS: This bulletin outlines multiple known areas of possible water entry for the vehicles listed above. It serves only as a diagnostic resource in troubleshooting water leak complaints from the roof area. This bulletin does not include all potential areas of water entry from the sunroof. Additional diagnosis may be required for vehicles which are not affected by the scenarios outlined below.
• 10176373May 1, 2020Electrical system. ACTIVE AIR FLAP FAULT DIAGNOSIS AND REPAIR: A check control message or MIL (Malfunction Indicator Lamp) may be illuminated with faults stored related to the upper and/or lower active air flap(s). Potential causes include: Faulty upper air flap actuator (G01 G02 G12 G30 G32) Faulty lower air flap assembly (G01 G02 G12 G30 G32) Software error in the DME affecting the upper flap (G01 G02 only)
• 10176367May 1, 2020Lane departure, Wheels. JERKING OR SHUDDERING FROM THE DRIVELINE (XDRIVE TRANSFER CASE ATX13-X): There is a jerking or shuddering during either or both of the following: Cornering or accelerating from low speeds Driving with low to medium loads There are no warning lights or Check Control messages. CAUSE Unevenly worn or incorrect fitment tires are installed on the vehicle or the factory-filled transfer case oil does not meet BMW…
• 10176366May 1, 2020Engine cooling, Brakes, Fuel system, Lane departure, Electrical system. COOLANT LINE QUICK DISCONNECTS LEAK IN LOW TEMPERATURES AT OR BELOW -15Ë?C (5Ë?F): The coolant reservoir in the high or low temperature cooling system is low There may be a coolant leak under the vehicle There may be a check control message (ID166) to top up coolant The low temperature cooling system have a low level warning indicator.
• 10176363May 1, 2020Engine cooling. TANK VENTILATION AND MIXTURE CONTROL FAULTS STORED IN THE DME: The Engine Malfunction Warning is illuminated and one or more of the following faults are stored in the DME.
• 10176360May 1, 2020Engine. B58C AND B58M ENGINES ENGINE OIL FILTER INSERT IS DIFFICULT TO REMOVE - REMOVAL: On rare occasions during an engine oil service the BMW Original (Genuine) engine oil filter insert is either difficult to remove or breaks apart in the oil filter housing. The engine oil filter is broken. The paper is torn and the lower plastic section is stuck in the engine oil filter housing.
• 10175293Apr 1, 2020Electrical system. REMOTE 3D VIEW NOT AVAILABLE: Remote 3D View cannot be launched In the BMW ConnectedDrive App. Software error in the Advanced Telematics Module 2 (ATM2).
• 10175292Apr 1, 2020Electrical system. BMW CONNECTEDDRIVE SERVICES ARE NOT AVAILABLE: The BMW ConnectedDrive services are not available for an extended period. This may include: Calls in the BMW Assistance app (Concierge Service) Vehicle data and status in the BMW ConnectedDrive app Remote services Remote 3D View Real Time Traffic Information (RTTI) Weather News Software error in Advanced Telematics Module 2 (ATM2).
• 10175287Apr 1, 2020Electrical system. SERVICE ACTION - REPLACE RIGHT FRONT SHORT RANGE RADAR SENSOR (SRR): The functionality of the right front SRR sensor could be reduced which would display the Driving Assistance Check Control Message.
• 10175286Apr 1, 2020Electrical system. SERVICE ACTION - REPLACE LEFT FRONT SHORT RANGE RADAR SENSOR (SRR): The functionality of the left front SRR sensor could be reduced which would display the Driving Assistance Check Control Message.
• 10175285Apr 1, 2020Electrical system. DEACTIVATION OF THE INTERIOR MOVEMENT DETECTOR/TILT ALARM SENSOR IS NOT POSSIBLE: Customer complains that the interior movement detector and the tilt alarm sensor system cannot be deactivated by pressing the lock button on the remote control / BMW display key twice. The second button press on the radio remote control / BMW display key is not detected. Customer may have to press the button 3 times to deactivate the…
• 10175272Apr 1, 2020Engine. DELIVERY STOP - REPLACE HIGH-PRESSURE PUMP: Due to an assembly error the flange bolts for the high-pressure pump did not have the proper tightening torque applied.
• 10175269Apr 1, 2020Engine cooling. ERRONEOUS ELECTRIC FAN FUNCTION FAULT STORED IN THE DME: The following faults may be erroneously stored in the Digital Motor Electronics (DME): Fault code: Control module: Fault code text: 1A2806 DME Electric fan function: limited operation 1A4007 DME Electric fan function: Operating mode implausible And: There is no customer-facing vehicle symptom(s) or related check control message displayed.
• 10174320Apr 1, 2020Electrical system, Equipment. CONNECTEDDRIVE/BMW ASSIST SYSTEM DIAGNOSIS INFORMATION: This Service Information Bulletin (Revision 7) replaces SI B84 02 14 dated May 2019. ConnectedDrive/BMW Assist features are partially or completely inoperative. This Service Information Bulletin: Is being published because vehicles are down for an extended period of time when researching system failures with ConnectedDrive or BMW Assist. Will assist you both…
• 10174319Apr 1, 2020Seat belts, Electrical system. FALSE WARNINGS THAT THE FRONT PASSENGER SEAT IS OCCUPIED WITHOUT THE SEAT BELT BUCKLED: This Service Information Bulletin (Revision 10) replaces SI B72 04 17 dated September 2019. Acoustic and visual warnings indicate that the front passenger seat is occupied and the safety belt is not fastened when the seat is actually unoccupied. If the situation is currently present sit in the seat and move the seat to a…
• 10174317Apr 1, 2020Latches, locks and linkages, Equipment. COMFORT ACCESS AND COMFORT GO NOT POSSIBLE: This Service Information Bulletin (Revision 1) replaces SI B66 19 19 dated May 2019. Vehicle cannot be unlocked/locked or started via Comfort Access. Remote control functionality is restored by pressing any of the key buttons or by removing and reinstalling the remote control key battery. The Display Key Digital Key and the Digital Key Card are not affected. Electrostatic…
• 10174316Apr 1, 2020Back-over prevention (rear camera), Equipment. REAR VIEW CAMERA FAILS TO DISPLAY IMAGE: This Service Information Bulletin (Revision 6) replaces SI B66 08 17 dated January 2020. Sporadically when the rear view camera is activated no image appears in the display. The rear view camera can be activated by either: 1. Selecting reverse with the shift selector 2. Camera activation via the button on the center console Camera function returns after a terminal change.
• 10174032Apr 1, 2020Equipment. AUTOMATED ACTIVATION OF NAVIGATION SYSTEM DURING PDI/QC1: This Service Information Bulletin (Revision 2) replaces SI B65 22 14 dated October 2015. The INITIAL NAV enabling code no longer needs to be pre-ordered through the Parts department!
• 10174031Apr 1, 2020Equipment, Electrical system. DISPLAYS SPORADICALLY REACT VERY SLOWLY WHEN SCROLLING IN THE AUDIO MENU: Sporadically the reaction time of the display in the instrument cluster the head-up display or in the CID (Central Information Display) is very long. This can occur when browsing/scrolling through lists in the audio menu switching radio stations or albums. Software in the Head Unit High (HU-H3).
• 10174027Apr 1, 2020Air bags, Electrical system, Exterior lighting. DAYTIME RUNNING LIGHT IS DIM OR DISCOLORED: This Service Information Bulletin (Revision 2) replaces SI B63 04 18 dated January 2019. One or more of the LED daytime running lights are dim or discolored. The connection between the LED module and light tube inside the headlight is damaged.
• 10174025Apr 1, 2020Electrical system. DIGITAL SPEEDOMETER MISSING FROM THE INSTRUMENT CLUSTER AFTER PROGRAMMING DIGITAL SPEEDOMETER MISSING FROM THE INSTRUMENT CLUSTER AFTER PROGRAMMING: This Service Information Bulletin (Revision 2) replaces SI B62 07 19 dated June 2019. The digital speed display in the Instrument Cluster (Kombi) is missing or is only displayed in Kilometers per hour after ISTA programming. There are no iDrive settings for a customer…
• 10174019Apr 1, 2020Engine. CCM DISPLAYED "INCREASED BATTERY DRAIN" CAUSED BY CONTROLLER: This Service Information Bulletin (Revision 1) replaces SI B61 05 20 dated February 2020. Electrostatic discharge at standstill / start engine. Energy management" The results of the Energy Diagnosis test plan identifies the Controller as the root cause of the CCM. The Controller delays the vehicle going to sleep by up to 6 minutes. In some cases this…
• 10174017Apr 1, 2020Visibility (wipers, defrost, mirrors), Back-over prevention (rear camera). KNOCKING NOISE FROM WASHER FLUID RESERVOIR: When driving over uneven pavement or cobblestones a knocking noise is present from the passenger side front area (A pillar). Once the vehicle is driven on a flat even surface; the noise is no longer present. CAUSE Washer fluid reservoir movement caused by mounting bracket clearance.

← All problems reported for the 2020 BMW X3