2015 BMW X5 Technical Service Bulletins

412 technical service bulletins (TSBs) are on record for the 2015 BMW X5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10151108Feb 1, 2016Electrical system. February 2016 General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 03 14 dated May 2015. SUBJECT Check Control Messages Related to Battery Charge during Cold Ambient Temperatures. On cold days (an outside ambient temperature below 15F), customers may notice a check control message related to the battery displayed on the instrument cluster and the control information…
• 10151098Feb 1, 2016Equipment, Tires. SI B36 01 15 February 2016 Wheel and Tires Technical Service This Service Information bulletin supersedes SI 36 01 15 dated October 2015. designates changes to this revision SUBJECT Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10151079Feb 1, 2016Fuel system, Equipment. SI B13 03 15 February 2016 Fuel Systems Technical Service This Service Information bulletin supersedes SI B13 03 15 dated March 2015 and replaces SI B13 04 13 dated March 2014. SUBJECT N20, N26, N55, N63TU, S63TU and S55 Engines: Bosch Injector ETK Part Number Error. The current version of the ETK incorporates multiple part number errors for the Bosch type injectors. Ordering the injectors by VIN number or manual…
• 10151078Feb 1, 2016Fuel system, Engine cooling, Electrical system. The DDE software application for exhaust gas recirculation control (EGR) does not favorably match the diesel fuel grades available in many parts of the US market. The high pressure EGR cooler could become filled with soot particulate to the point that exhaust gas flow and cooling efficiency are significantly reduced. This could result in the Service Engine Soon light coming on with EGR control / Air mass faults…
• 10151075Feb 1, 2016Engine, Electrical system. Under certain engine operating conditions the measured air mass between the cylinder banks 1-4 and 5-8 is miscalculated by the DME's. This could result in incorrect engine torque and mismatched ignition parameters with the possibility of internal engine damage.
• 10151025Jan 1, 2016Equipment, Electrical system. "?This Service Information bulletin supersedes SI B65 13 13 dated October 2014. SUBJECT Headunit-High: CID Is Blank and ""NO SIGNAL"" Is Displayed . Intermittently the Central Information Display (CID) is blank and ""NO SIGNAL"" is displayed on the CID. Fault Code B7F8C3 ""no response from CID (HW error: loss of CID communication)"" is stored in the HU-H Note: If Fault Code E1C440 ""Headunit Reset"" is also stored…
• 10151023Jan 1, 2016Equipment. Whistling Noise Coming from the Center Vent - A/C is Off . A very high pitched whistling or beeping noise is heard coming from the center vents. The flow of refrigerant through the expansion valve at certain temperature differentials.
• 10151019Jan 1, 2016Electrical system. Instrument Cluster Multifunction Display Intermittently Blank . Some information displays in the Instrument Cluster (KOMBI) may intermittently go blank. This may include the tachometer and speedometer displays. There is a software error in the KOMBI.
• 10151016Jan 1, 2016Electrical system. "Vehicles which have had the Instrument Cluster (KOMBI) replaced may display incorrect CBS (Condition Based Service) data after programming. AFFECTED VEHICLES Vehicles which require this Service Action to be completed will show it as ""Open"" when checked either in the ""Service Menu"" of DCSnet (Dealer Communication System) or with the Key Reader. Incorrect SW calibration loaded after KOMBI replacement."
• 10151015Jan 1, 2016Electrical system. SI B61 30 14. January 2016. General Electrical Systems Technical Service This Service Information bulletin supersedes SI B61 30 14 dated December 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure . INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the…
• 10150905Jan 1, 2016Fuel system, Equipment. SI B16 15 14 January 2016 Fuel Supply Systems Technical Service.This Service Information bulletin supersedes SI B16 15 14 dated December 2014, designates changes to this revision. SUBJECT NVLD Tank Leakage FC 190302 Fuel Tank Ventilation and Purge Air System Micro Leak . The engine malfunction warning is illuminated and the following fault code is stored in the DME memory: FC 190302 Fuel tank ventilation and purge…
• 10147884Dec 1, 2015Electrical system. Instrument Cluster Outside Temperature Display Implausible. INFORMATION This service information bulletin provides technical, diagnostic and/or repair-related information. Eligible and Covered Work/Repairs To submit a claim for the repair of a verified defect in materials or workmanship, please following the established and applicable warranty policy and procedures together with the using corresponding defect code…
• 10147882Dec 1, 2015Electrical system. "?SI B61 30 14December 2015 General Electrical SystemsTechnical Service This Service Information bulletin supersedes SI B61 30 14 dated July 2015. designates changes to this revision SUBJECT BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement…
• 10147881Dec 1, 2015Visibility (wipers, defrost, mirrors). "The Low Washer Fluid Warning Light is illuminated when the Washer Fluid Tank is Full. INFORMATION The use of a ""non-approved"" washer fluid can cause the low fluid warning light to come on even when the reservoir is full. An analysis of parts returned to warranty has shown the sensor is operating correctly. Do not replace the reservoir with integrated sensor for these situations.
• 10147879Dec 1, 2015Visibility (wipers, defrost, mirrors). Sunroof Makes a Creaking Noise During Operation. When opening or closing the sunroof a creaking/ crackling type noise is heard. Insufficient lubrication of the sunroof guide rails
• 10147870Dec 1, 2015Brakes. Ticking Noise from the Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a metallic ticking from the area of the front wheels. Movement between the inner contact surfaces of the brake disc and drive flange of the wheel bearing hub.
• 10147867Dec 1, 2015Engine. ?SI B13 10 15 Fuel Systems December 2015 Technical Service. This Service Information bulletin replaces SI B13 07 15 dated August 2015. The DDE software release for the Engine Start-Stop (MSA) function is incomplete. As a result the (MSA) feature cannot be activated with the MSA On/Off switch.
• 10147838Nov 1, 2015Equipment, Electrical system. Comfort Access Does Not Function After Vehicle Enters Sleep Mode. Sporadically, when the vehicle has been locked and is in sleep mode, the vehicle will not waken when trying to unlock the vehicle with comfort access from any door. The vehicle can be unlocked from the remote. After waking, the comfort access function is restored. Software fault in the BDC.
• 10147833Nov 1, 2015Electrical system, Equipment. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147831Nov 1, 2015Electrical system. "Instrument Cluster display inoperative FC B7F689. The Instrument Cluster (Kombi) is intermittently inoperative with fault code B7F689 ""display backlighting and graphics PCB switched off"" stored. Kombi software."
• 10147830Nov 1, 2015Electrical system. "Instrument Cluster display is partially blank. INFORMATION Covered under the terms of the BMW New Vehicle Limited Warranty for Passenger Cars and Light Trucks or the BMW Certified Pre-Owned Program. If you are using a Main labor code for another repair, use the Plus code labor operation 00 00 556 instead. Refer to KSD2 for the corresponding flat rate unit (FRU) allowances.
• 10147822Nov 1, 2015Transmission and drivetrain. Leaking Rear Differential (QMVH). There is an oil leak from the rear differential housing. The liquid-type sealer used between the main differential housing and the outer superimposing gear units has failed.
• 10147779Oct 1, 2015Electrical system. Instrument Cluster display is partially blank. The Instrument Cluster (Kombi) lower display may be intermittently blank. The Board Computer, Ambient Temperature and Check Control Messages will not display. Instrument Cluster software error.
• 10147771Oct 1, 2015Tires. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147261Sep 1, 2015Equipment, Seats, Electrical system. "Third Row of Seats Blower is Inoperative. The blower in the third row of seats is not working and the fault code ""E70C32 - AC-LIN: Heating in third row of seats is not responding"" has been entered in the IHKA (Integrated Heating and Airconditioning, Automatic) control unit. CAUSE LIN BUS short or open circuit in wiring or connectors Blower motor, micro switch defective Control unit, A/C, for 3rd seat row…
• 10147257Sep 1, 2015Steering. Grating or Scraping Noise When Turning Steering Wheel. There is a grating or scraping noise when the steering wheel is turned. The noise comes from the steering column switch cluster (SZL), coil spring or steering wheel. CAUSE When the steering wheel is turned, the connection between the steering wheel and the steering column switch cluster causes torsional stress, which creates a noise in the coil spring cassette.
• 10147244Sep 1, 2015Brakes. This Service Information bulletin supersedes SI 37 02 14 dated February 2015. Unfavorable tolerances for the plug-in connections of the wheel acceleration sensors may result in fault code memory entries and the VDC being deactivated. If the VDC control unit identifies an implausable value from one of the wheel acceleration sensors, the VDC will be deactivated and the driver is informed by a Check Control message…
• 10147243Sep 1, 2015Tires. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147242Sep 1, 2015Brakes. Diagnosis of Compound Brake System Complaints in M Vehicles This Service Information bulletin supersedes SI 34 04 14 dated December 2014. Designates changes to the bulletin. INFORMATION 1.Visible cracks are caused by high thermal stresses during rapid heating and cooling of the brake discs. Braking from high speed with cold brake components (less than 212 degrees F) increases the likelihood of cracks to form.
• 10147241Sep 1, 2015Wheels, Transmission and drivetrain. Shudder from the Driveline on Vehicles with xDrive. There is a shudder or vibration from the driveline when taking off from a stop, or when accelerating at highway speeds. CAUSE Possible multiple root causes related to the engine, wheels & tires, suspension components or internal wear on the clutch plates of the xDrive transfer case.
• 10147239Sep 1, 2015Steering, Electrical system. "N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the ""engine stop"" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE)…
• 10151410Aug 1, 2015Brakes. After Cold Start, Brake Booster Reservoir Vacuum Reduced. With an outside temperature below 14ºF, brake booster vacuum may be reduced after a cold start. The non-return valve in the vacuum line to the brake booster may stick at temperatures below 14ºF. Sufficient vacuum supply is available again at the brake booster only after the vehicle is driven (approximately 1/4 mile).
• 10151404Aug 1, 2015Transmission and drivetrain. Vibration or Shudder from Driveline when Accelerating from a Stop. Chassis stabilization warning is displayed. Vehicle may exhibit a shudder or vibration when taking off from a stop. One or more of the following fault codes may be stored: LMV ? 440101 - Transfer box (VTG): End of transmission service life reached ? 440105 - Transfer box (VTG ) Calibration Faulty ? 440115 - Transfer box (VTG): Calibration angle…
• 10151402Aug 1, 2015Equipment, Steering, Electrical system. "N57T - Automatic Start/Stop (MSA) Does Not Function. The MSA feature to shut the engine off does not function at any time, although it is set to active. The MSA test plan indicates that the ""engine stop"" inhibitor is currently active due to missing steering angle information. There are no relevant faults stored and the steering angle is calibrated correctly. CAUSE A communication error between the engine (DDE)…
• 10147211Jul 1, 2015Equipment. NAV Road Map Installation Using USB Stick. INFORMATION The Navigation road map can be installed onto the head unit in the vehicle using a USB stick connected to the USB connector in the center console in the vehicle. ? 32GB USB stick is necessary ? Desired NAV road map version can be retrieved from the HDD-Update console PROCEDURE 1. Copy the desired NAV road map from the HDD-Update console onto a 32GB USB stick…
• 10147205Jul 1, 2015Seats, Electrical system. Rear Seat Heater Inoperative. The front passenger and both rear seat heaters do not work. The following fault codes are stored in the BDC (Body Doman Controller): D90C18 - LIN master I: Short circuit D90C1A - LIN master I: Communication faulty CAUSE One of the rear seat heater modules has an internal fault, which interrupts LIN bus communication.
• 10147202Jul 1, 2015Equipment. "Affected vehicles in dealer inventory must not be retailed or delivered until the label is removed. Vehicles at ports of entry will be remedied prior to dealer delivery. On affected vehicles, there is an incorrect label regarding the appropriate engine oil. Affected vehicles can be identified with a ""Vehicle Comment"" in the DCS Warranty Vehicle Inquiry or ISPA Light. Remove the engine oil label (located in the…
• 10147200Jul 1, 2015Transmission and drivetrain, Wheels, Brakes. Ticking Noise from Front Axle When Cornering. The customer may complain of a ticking noise from the front axle when cornering, maneuvering, parking or pulling away from a parking space. The noise can be heard as a light metallic ticking from the front outer cornering wheel. Movement between the brake disc and wheel bearing hub.
• 10147195Jul 1, 2015Steering. Noise When Adjusting the Steering Column Up or Down. Creaking noise when raising or lowering the steering column position CAUSE Steering column adjustment
• 10147190Jul 1, 2015Engine cooling, Vehicle speed control, Electrical system. "Reduced Engine Power with ""Charging Pressure Too High"" Faults Stored. When accelerating under certain conditions, the engine power may be reduced and a Check Control Message (CCM) ""Drive Faulty; Drive at moderate speed"" is displayed. The following charging pressure control fault is stored in the DME: ? Fault 120208: Exhaust camshaft sensor, signal: not plausible As a result, the engine power is reduced, and…
• 10147189Jul 1, 2015Electrical system, Fuel system. Engine Malfunction Warning Illuminated with FC 193208: Fuel Level Plausibility Stored in DME. The customer states that the engine malfunction warning lamp is illuminated, and while filling the fuel tank, the fuel gauge did not show the proper fill level. After the vehicle is driven a short distance, the fuel gauge will update to full. When diagnosed, the following fault is stored in the DME: ?
• 10059004Jul 1, 2015Engine, Electrical system. Check control message (ccm) "drive faulty; drive at moderate speed" will display and engine power may go down when accelerating under certain conditions due to dme software error.
• 10147722Jun 1, 2015Electrical system. "BMW Maintenance Program: 12-Volt Battery Replacement Measure. INFORMATION This bulletin outlines a customer satisfaction measure that has been designed exclusively for the BMW vehicles listed above. It involves the replacement of the 12-volt battery as a preventive maintenance measure. This 12-volt battery replacement measure is: ? Effective for repairs dated on or after January 1, 2015. ? Applicable to vehicles…
• 10147716Jun 1, 2015Tires, Wheels. Check Control Message: Tire Pressure Monitor (RDCi) Failure. A Check Control Message states Tire Pressure Monitor (RDCi) has failed CAUSE Hardware in the remote control unit (FBD3 antenna)
• 10147715Jun 1, 2015Suspension. Clicking Noise from Front Axle. Clicking noises are heard from the front axle area while maneuvering at low speeds (e.g., parking lot maneuvers). CAUSE Movement between the contact surfaces of the wheel bearing and swivel bearing (knuckle)
• 10058488Jun 1, 2015Equipment. Bmw: the chrome material adhesion is poor and causes chrome ring to peel on idrive controller and needs to be replaced.
• 10058424Jun 1, 2015Tires. Bmw: some vehicles experiencing the failure of tire pressure monitor (rdci) due to remote control unit hardware (fbd3 antenna) and needs repairing. Model years 2014-15.
• 10147154May 1, 2015Equipment. HU-H: Headunit Resets Intermittently or Permanently. The HU-H (Headunit-High) resets intermittently or permanently. ? The display is inoperative and there is no audio output ? Automatic system start-up after a couple of seconds CAUSE Software error in the HU-H
• 10147151May 1, 2015Equipment. A/C Operation: Reduced or No Airflow After Long Drive. The customer complains of reduced air-conditioning air flow when driving for a long period, usually greater than 30 minutes. This time varies based on outside temperature and humidity. The A/C low-pressure lines and evaporator are starting to freeze up.
• 10147150May 1, 2015Equipment. A/C Makes Unusual Whistling Noise from Center Vents. An unusual whistling noise can be heard coming from the center vent area for approximately15 seconds after the A/C is switched on. CAUSE Evaporator in the A/C system

← All problems reported for the 2015 BMW X5