2017 GMC Yukon Denali Technical Service Bulletins

549 technical service bulletins (TSBs) are on record for the 2017 GMC Yukon Denali. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10167461Oct 25, 2019Vehicle speed control. This Preliminary Information communication provides information to the technician about vehicles that have a detent / click with a feel of increased resistance when the accelerator pedal is about ¾ of the way. The new accelerator pedal design has a built-in detent position near the last 1/4 of pedal travel. Dealer should communicate to the customer this is a normal operating characteristic of the vehicle and no…
• 10167460Oct 25, 2019Lane departure. This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view…
• 10167439Oct 15, 2019Electrical system. This Preliminary Information communication provides information to the technician on how the radio display gets the air ambient temperature. On 1500 series trucks and all sport utility vehicle with regular production option code IO3 radio the ambient air temperature sensor is hard wired to the engine control module and then the signal goes on high speed local area network to the body control module from there on…
• 10167426Oct 3, 2019Electrical system. This Preliminary Information communication provides information and definitions to the technician about vehicles that have fishbite, chuggle, misfire, AFM disturbances or torque converter shudder/vibration concerns. Technician are advised to use PICO software to determine root cause of the concern. If torque converter shudder is confirmed technicians are referred to Torque Converter Diagnosis in SI.
• 10167425Oct 3, 2019Forward collision avoidance. This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
• 10165920Sep 30, 2019Body and structure. This Preliminary Information communication provides information to the technician about vehicles with erratic or hesitation when opening and closing the power liftgate. There may be a diagnostic trouble code B153A set in the power liftgate module. This concern could occur if the left liftgate actuator is internally coming apart. The actuator will need to be replaced however care must be taken when removing the…
• 10165899Sep 23, 2019Transmission and drivetrain. This Preliminary information communicates to the dealer technician that if they are unable to perform the solenoid characterization using the transmission unit number (TUN) off a replacement 8L90 RPO M5U automatic transmission to refer to the TUNs listed in this PI. If the TUN off the replacement transmission is listed they should refer to bulletin 18-NA-355 and perform a transmission fluid exchange due to possible…
• 10165870Sep 5, 2019Engine cooling. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
• 10165868Sep 5, 2019Forward collision avoidance. This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
• 10165865Sep 4, 2019Steering. This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist. Starting with 2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane…
• 10164757Aug 8, 2019Visibility (wipers, defrost, mirrors), Steering, Electrical system. This Preliminary Information communication provides information to the technician about vehicles that may have any of these concerns remote keyless entry, passive Entry and Start Inoperative, No Fob detect message on driver information center, service tire pressure system, no audio, touch screen Inoperative, Steering Wheel Controls Inoperative, Service Stabilitrak, rear power windows inoperative, rear wiper…
• 10163690Jul 31, 2019Equipment. This Preliminary information communicates AFM / DFM usage Information. providing additional information on the AFM and DFM systems
• 10163684Jul 29, 2019Electrical system. This Preliminary Information communication advises the technician with a tip when the vehicle stops running after it has been idling for 2.5 hours. This is normal operation of the vehicle built with regular production code BTM and without Regular Production Option Code AVF. If the vehicle was built with regular production code BTM and AVF only has a 1 hour idle time.
• 10163657Jul 9, 2019Lane departure. This Preliminary Information communication provides information to the technician about vehicles that may have Service Front Camera, Service Lane Departure Warning, and Service Lane Keep Assist Message. Technician may find Diagnostic Trouble Code B1008 Sym 4B set. Technician will need to check the windshield to ensure it is not aftermarket. Technician will also check for anything that may impair the front view…
• 10162161Jun 26, 2019Electrical system. This Preliminary information communication provides information to the technician about vehicles with the rear body fuse block with a loose fuse connection. Technician will need to check terminal tension on the rear fuse block. Technician will need to replace the rear body fuse block if poor terminal tension is the issue. Technician will need to replace the appropriate terminated lead if something other than the…
• 10162151Jun 24, 2019Electrical system. This Preliminary Information communication provides information to the technician about how to diagnosis a battery draw that may be caused by a module back feeding voltage in the ignition relay circuits making the vehicle think it is still awake.
• 10162143Jun 19, 2019Engine cooling. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on. Technician will find Diagnostic Trouble Codes P0340 and P0341 setting at times. Technician should use normal published Service Information diagnostics. If normal Service Information diagnostics does not isolate the concern, inspect for corrosion in connector…
• 10162136Jun 17, 2019Fuel system. This Preliminary Information communication provides information to the technician for a vehicle setting both a P2635 and P018B diagnostic trouble codes. The following steps may help to determine if this is caused by a fuel pressure sensor not reading the low end of the pressure range. Technician is to make sure the engine is cold and install the Multiple Diagnostic Interface along with Global Diagnostic System 2.
• 10162127Jun 14, 2019Suspension. This Preliminary Information communication provides information to the technician about vehicle with Service ABS and/or Traction control lights/message on, Service Power Steering System, Service Suspension System, and or Loss of communication with EBCM, SWPS, PSCM, and/or SCM. Technician may find Diagnostic Trouble Codes U0077, U0121, U0126, U0131, U0139, U0401, U0415, and/or U0428. Technician should remove the…
• 10161019May 15, 2019Forward collision avoidance. This Preliminary information communicates a "Forward Collision System Reduced" message displayed on the DIC when the Forward Automatic Braking has been set to the "Alert" setting. This is normal when the FAB has been set to "Alert".
• 10161010May 13, 2019Body and structure. This Preliminary information communicates that unwanted liftgate opening can occur if the customer leaves a programmed fob in the vicinity of the passive liftgate antenna. If the antenna can locate a programmed fob in said area, the gate will open if the liftgate open switch or hands free sensor is activated.
• 10160989May 7, 2019Engine cooling. This Preliminary information communicates A vehicle may have a concern of DTC P050D setting along with a P0300 after a cold start up. White smoke and/or coolant odor may come from exhaust for an extended period of time at cold start as well. Cause Coolant getting into the cylinders, and provides direction for the repair.
• 10160978May 3, 2019Body and structure. This Preliminary Information communication provides information to the technician about vehicle that may have wind whistle noise heard from the right or left rear quarter glass area when driving at highway speeds or with a cross wind. Technician will inspect the quarter glass for excessive urethane. If excessive urethane is found use a sharp knife and cut off the excessive urethane. Also the technician will install…
• 10160687Apr 24, 2019Engine. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a buffeting vibration and/or drone type noise, exhaust tone change, and/or body pressure booming. Replace or repair any of the issue that was found in the inspection. If the vehicle is equipped with a 4.3 liter or 5.3 liter engine an updated exhaust system is now available.
• 10160676Apr 18, 2019Brakes. This Preliminary Information communication provides information to the technician on the step needed to diagnose and repair vehicles that may have uneven brake pad wear. Technician will need to inspect and measure the brake pads thickness. Also determine the customer?s driving style. The disc brake pads should only be replaced if the friction surface is worn to within 2.0 mm (0.079 in) of the mounting plates.
• 10160665Apr 15, 2019Electrical system, Brakes. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have an intermittent "Check Trailer Wiring" or "Service Trailer Brake" message on the Driver Information Center. Technician will inspect and clean the ground wire (normally white wire) connection on the trailer side of the 7-pin connector. Inspect that the wires inside the trailer…
• 10160663Apr 12, 2019Equipment. This Preliminary information communicates an issue with aftermarket USB chargers causing SIR DTC's to set.
• 10160662Apr 12, 2019Electrical system. This Preliminary Information communication provides information to the technician about vehicles that the speedometer needle appears to be inaccurate. Dealer should advise the customer the specification for speedometer needle accuracy is +/- 2 MPH at any given speed when looking straight at the needle.
• 10160659Apr 11, 2019Body and structure, Electrical system. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that have remote start is inoperative, power lift gate Regular Production Option Code (TB5) is inoperative with the ignition off, Crank no start, Start and Stall, and vehicles equipped with the diesel engine, the blower motor may stay on after the engine is turned off. Technician may find…
• 10156933Mar 15, 2019Equipment. This Preliminary Information communication advises the technician that the Product Quality Center part restriction has ended for the 8L45 and 8L90 park actuator rod.
• 10156912Mar 6, 2019Engine cooling, Engine. This Preliminary Information communication provides information to the technician on the steps to diagnose and repair vehicles that may have a Service Engine Soon Malfunction Indicator Lamp on at low mileage. Technician may find Diagnostic Trouble Codes P0420 and or P0430 stored. Technician should be advised that the catalytic converter efficiency Diagnostic Trouble Codes P0420 and P0430 are disabled for the first…
• 10154322Feb 25, 2019Back-over prevention (rear camera). This Preliminary information communicates repair information for the rear vision camera or surround vision camera image being: - Yellow - Blurry - Distorted - Image scrolling - Image with NO gridlines - Screen is blue with gridlines - Screen is blue with Service Rear Vision System message
• 10154319Feb 25, 2019Latches, locks and linkages. This Preliminary Information communication provides information to the technician about vehicles that have the alarm sounding when learning new key fobs after the original key fobs were lost. Technician will open the driver's door and allow the Content Theft Deterrent alarm to activate, which will pulse the horns and exterior lamps for approximately 30 seconds and the alarm will shut off at this time.
• 10154312Feb 21, 2019Transmission and drivetrain. This Preliminary Information communication provides information to the technician that a whine noise heard from the automatic transmission fluid pan hear with the the key on and engine off, or for up to one minute after the vehicle has been shut off should be deemed a normal characteristic.
• 10154301Feb 18, 2019Electrical system, Other or unknown. This Preliminary Information communication provides information to the technician that a customer may request the factory Integrated Trailer Brake Control be bypassed and their aftermarket trailer brake controller be installed instead. Technician will need to gain access to the body harness. Install trailer brake controller harness General Motors part number 23184088 into Middle Bus Electrical Center (X61A).
• 10154300Feb 18, 2019Steering. This Preliminary Information communication provides information to the technician about vehicles that show a "Take Steering" message on the Driver Information Center along with a warning chime/alert. Dealer should be advised the purpose of the message is to alert the driver that the Lane Keep Assist system has not detected active steering input from the driver (hands off the steering wheel).
• 10154298Feb 15, 2019Electrical system. This Preliminary Information communication provides information to the technician with the correct way to remove the front shock electrical connector terminals. Technician will need to slightly bend the end of the J-38125-12A release tool. There is a purple Terminal Position Assurance that will align itself in the release position when the release tool is inserted into the release hole.
• 10154290Feb 8, 2019Electrical system. This Preliminary Information communication provides information to the technician about the text messaging feature on some newer General Motors infotainment systems. Pair the iPhone to the system then enter the Bluetooth settings menu, select the ?i? icon next to the vehicle name in the device and enable show notifications. The text messaging feature will be available on the next ignition cycle.
• 10154280Feb 8, 2019Electrical system, Engine. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that have a no crank or a start and then immediate stall, Service Engine Soon Malfunction Indicator lamp may not be on when the ignition is in the run position. Technician may find Diagnostic Trouble Codes P0513 and or P262B may also be set. Technician will pulled the driver sill plate and…
• 10154276Feb 7, 2019Engine cooling. This Preliminary information communicates P0016 setting after internal engire repair. The engine Base timing is not being set correctly. The information in this PI will be helpful in setting the timing in the vehicle.
• 10154604Dec 17, 2018Engine cooling. This Preliminary Information communication provides information to the technician about vehicles that have an intermittent no crank, no start, or start stall concern with the security light coming on. Technician may find Diagnostic Trouble Codes B3055, B3060, and/or B3935. Technician should not replace any parts for this concern. If unable to duplicate the concern ask if the customer uses any Radio Frequency…
• 10154583Dec 13, 2018Brakes. This Preliminary Information communication provides information to the technician about fluid leaking from the brake caliper piston area found during a service of the vehicle. The substance is actually excess assembly grease from the caliper boot and piston installation. This grease can be cleaned off and the rest of the service completed.
• 10154553Dec 3, 2018Engine cooling. This Preliminary Information communication advises the technician that generation 5 engines with Regular Production Option Code L83, L86, or LV3 may have an oil consumption concern were one quart in 2000 miles is being used. Dealer will confirm oil level was properly checked per Owner's Manual, and check the bolt torque on the Valve Lifter Oil Manifold Assembly, before doing any repairs to the vehicle.
• 10151860Nov 19, 2018Seats. This Preliminary Information communication provides information to the technician on how to diagnose and repair vehicles that may have a rattle noise from the second row seat. Technician will need to inspect the striker not aligned properly in latch opening. To repair this condition, rework/adjust the striker in the direction to center it in the latch opening. An adjustable wide mouth metal working tool may be used…
• 10147382Oct 16, 2018Engine cooling. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp on, engine misfire, and/or engine noise. Technician may find Diagnostic Trouble Codes P0300-P0308.
• 10145501Sep 19, 2018Transmission and drivetrain. This Preliminary information communicatesSES lamp, setting DTC P0333 when shifting the Transmissionfrom park.DTC P0333 cansetdue to voltage from the Transmission park/neutral signal 1circuit bleeding into the knock sensor system circuits.If SI does not isolate the concern inspect the K20 ECM connector X2 looking for debris, connectorand or terminal concerns.
• 10145486Sep 14, 2018Suspension. This Preliminary Information communication provides information to the technician with the steps to diagnosis and repair vehicles with various handling, vehicle dynamics concerns, noises from the suspension or underbody, or issues related to damaged suspension components. Before any in-depth diagnostics are performed, be aware that various issues could occur if the vehicle has been modified and inform the customer…
• 10144464Aug 20, 2018Lane departure. This Preliminary Information communication provides information to the technician with additional information on the functionality of Lane Keep Assist.Starting with2016 model year Lane Keep Assist Regular Production Option Code (UHX) replaced Lane Departure Warning Regular Production Option Code (UFL). Lane Keep Assist is designed to assist the driver in keeping the vehicle from drifting out of a driving lane that…
• 10143757Jul 9, 2018Transmission and drivetrain. This Preliminary information communicates to the dealer technician thatLight Duty Trucks equipped with automatic transmissions and 4 wheel drive may exhibit a condition of grinding/ratcheting type noise when shifting the automatic transmission into park while the transfer case is in 4 wheel drive low (4LO) range. Dealers technician's are advised this condition should be deemed a normal characteristic of 4WD low…
• 10143459Jun 27, 2018Equipment, Engine. This Preliminary Information communication provides information to the technician about vehicles that have the oil pressure gauge jumps from approximately 40 lb. to 60 lb. The 4.3L (LV3), 5.3L (L83), 6.2L (L86) engines are equipped with a two stage oil pump. Dealer should advise the customer this is normal operation for these engines.

← All problems reported for the 2017 GMC Yukon Denali