2017 Mazda CX-3 Technical Service Bulletins

519 technical service bulletins (TSBs) are on record for the 2017 Mazda CX-3. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10170814Jan 23, 2020Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
• 10170813Jan 23, 2020Equipment, Electrical system. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem  P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service…
• 10170943Jan 15, 2020Equipment, Electrical system. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10170829Jan 15, 2020Engine cooling, Electrical system, Body and structure. LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10170817Jan 13, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
• 10170662Jan 10, 2020Latches, locks and linkages, Body and structure, Equipment. Some vehicles may exhibit rust (A) on the liftgate around the border of the rear mount camera (B) and/or the liftgate opener switch (C). Repair the paint rust and install a pad to prevent future paint rust.
• 10170661Jan 9, 2020Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement.  Mazda vehicles are…
• 10170656Jan 9, 2020Suspension, Equipment. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10169542Dec 19, 2019Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).
• 10169540Dec 19, 2019Equipment, Engine cooling. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold.
• 10169513Dec 18, 2019Other or unknown, Transmission and drivetrain. WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
• 10169539Dec 17, 2019Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is…
• 10169543Dec 13, 2019Equipment, Other or unknown, Visibility (wipers, defrost, mirrors). Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window…
• 10169537Dec 13, 2019Equipment, Engine cooling. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10169509Dec 5, 2019Engine cooling, Transmission and drivetrain. GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a…
• 10168785Nov 26, 2019Engine cooling. Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
• 10168139Nov 20, 2019Electrical system, Equipment, Engine cooling. Some customers may complain about:  Intermittent engine no start  Instrument cluster red security indicator light ON  Engine Start/Start Button Amber indicator light flashing  Battery discharge  Electrical relay buzzing noise  DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by:  A key in a purse near a cell phone. The cell phone radio…
• 10168118Nov 20, 2019Equipment, Engine cooling, Electrical system. Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint:  MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE  CANNOT COMMUNICATE WITH VEHICLE  ERROR MESSAGE INSTALLED ON ANDROID DEVICES  COMMUNICATION ERRORS  MMS CHECK MODE - Use to verify system operation (see below).
• 10168070Nov 6, 2019Equipment. Be advised that TSB 07-001/19 is no longer valid and has been superseded to "SSPB8 - 2016-2017 CX-3 A/C CONDENSER WARRANTY EXTENSION".
• 10168072Nov 4, 2019Equipment, Engine, Electrical system. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block…
• 10166896Oct 17, 2019Equipment. The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no mileage limitation. Concern Outline On certain subject CX-3 vehicles, the A/C condenser may be corroded, causing an A/C refrigerant leak. Vehicles with this condition may exhibit no…
• 10166848Oct 8, 2019Engine cooling. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
• 10165676Sep 30, 2019Engine cooling. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold.
• 10165653Sep 24, 2019Brakes. Some vehicles may exhibit a rattle / knock noise from the front disc brake caliper (1) when driving on a rough road surface.This is caused by the slide pin (1) hitting the mounting support (2) due to insufficient holding power of the dust boots (3) when a shock (4) is applied from the road. To eliminate this concern, the dust boots have been modified to increase holding power.
• 10165343Sep 10, 2019Equipment. Some customers may complain about warm air from the climate control vents. This may be caused by improper brazing of the evaporator, causing a refrigerant leak from the joint between the tubes and the header.
• 10165342Sep 10, 2019Equipment. Some customers may complain about warm air from the climate control vents when the air conditioner is ON. This may be caused by condenser corrosion, causing a refrigerant leak. The manufacturer of the condenser has been changed and the configuration of the condenser tube has been improved.
• 10165350Sep 6, 2019Body and structure, Engine cooling. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10165351Sep 4, 2019Equipment. The warranty coverage for the repair of the A/C Condenser due to refrigerant leak from condenser caused by corrosion is extended to 7 years (84 months) from the original New Vehicle Limited Warranty (Normal Warranty) start date, with no mileage limitation. Concern Outline On certain subject CX-3 vehicles, the A/C condenser may be corroded, causing an A/C refrigerant leak. Vehicles with this condition may exhibit no…
• 10164267Aug 23, 2019Engine cooling. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10163827Aug 7, 2019Equipment, Electrical system. After the installation of a new instrument cluster, the message "Fctry" or “Factory” is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are…
• 10163825Aug 7, 2019Exterior lighting, Brakes, Electrical system, Visibility (wipers, defrost…. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3)…
• 10163334Jul 31, 2019Equipment. The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download.
• 10163327Jul 30, 2019Forward collision avoidance. Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure…
• 10163385Jul 26, 2019Seats. Some customers may notice that the driver's seat gradually moves downward by itself and needs to be re-adjusted after 3 or 4 days of driving. This concern may be caused when a load, which is applied to the seat during braking, exceeds a specified level and may impact the retaining mechanism of the seat lifter and cause the seat to move downward. To eliminate this concern, the rigidity of the retaining mechanism of…
• 10163356Jul 26, 2019Electrical system, Equipment. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10163365Jul 22, 2019Steering. Some vehicles may exhibit a light resistance and/or an unusual noise when turning the steering wheel to the left. This concern may be caused by insufficient lubrication of the gear due to uneven and deteriorated grease. To eliminate this concern, the production process for steering shaft has been modified.
• 10163367Jul 16, 2019Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available…
• 10163364Jul 12, 2019Steering. Some customers may find a piece of aluminum tape and/or black liquid on the driver side floor. The aluminum tape may have dropped from the bottom of the steering column and the black liquid is grease that has melted and dripped onto the floor. This concern is caused by the grease from the power steering motor seeping out and loosening the adhesive on the aluminum tape. Parking in the sun can create high interior…
• 10163333Jul 9, 2019Equipment, Electrical system. Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
• 10162027Jun 25, 2019Equipment. ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/
• 10162014Jun 6, 2019Electrical system, Equipment. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda’s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10160583May 23, 2019Steering. Some vehicles may exhibit wear/peel-off of the leather steering wheel surface causing a poor appearance. This concern may be caused by an insufficient wear resistance of the steering wheel surface.
• 10160555May 20, 2019Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil…
• 10160575May 1, 2019Equipment, Electrical system, Back-over prevention (rear camera). Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
• 10160552May 1, 2019Suspension. Some vehicles may experience a creaking noise from the front shock absorber when going over bumps. Upon inspection, the coil spring is found to be broken at the lower part without any trace of an accident. It may be found during maintenance or service opportunity without customer complaints. Mud and sand caught between the coil spring and the lower spring seat causes paint damage on the coil spring, resulting in…
• 10159204Apr 8, 2019Suspension, Wheels. There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
• 10159198Apr 5, 2019Equipment, Electrical system. Apple carplayã¢â„⢠/ android autoã¢â„⢠frequently asked questions (faq)
• 10159201Apr 1, 2019Equipment. MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any…
• 10155442Mar 27, 2019Equipment, Electrical system. APPLE CARPLAY™ / ANDROID AUTO™ FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers.
• 10155437Mar 27, 2019Transmission and drivetrain. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: Depends on the vehicle’s speed only (the more speed, the more noise)Occurs with all types of driving (acceleration, deceleration, steady speed)Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration…

← All problems reported for the 2017 Mazda CX-3