2022 Mazda CX-30 Technical Service Bulletins

419 technical service bulletins (TSBs) are on record for the 2022 Mazda CX-30. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10233704Mar 1, 2023Visibility (wipers, defrost, mirrors). Some customers may report an odor or water in the HVAC system and upon inspection, the cabin air filter may be found to be wet.
• 10233562Mar 1, 2023Engine cooling, Exterior lighting, Equipment, Latches, locks and linkages. Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF
• 10232298Feb 24, 2023Exterior lighting. Some customers may notice an abnormal noise (i.e. whine, groan, rattle or squeak) coming from the front combination lights when turning them on, or a few minutes after turning them off. The noise may be due to contamination by foreign matter during the manufacturing process. The fan motor bearing may become worn out during use. To eliminate the noise, the production process at the supplier and the material has been…
• 10232297Feb 23, 2023Visibility (wipers, defrost, mirrors), Body and structure. Some vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty corrosion, may drip out from gaps under the outer mirror…
• 10232274Feb 16, 2023Engine cooling. Some customers may experience the check engine light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable.
• 10232285Feb 9, 2023Seats, Other or unknown. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs “B1030:13” and/or “B1032:13” are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat…
• 10232281Feb 7, 2023Body and structure, Other or unknown, Latches, locks and linkages. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate. To eliminate this concern, the internal structure of the latch and surface treatment of the bolts have been modified.
• 10232303Feb 6, 2023Equipment, Engine cooling, Electrical system, Exterior lighting. Some customers may complain about any of the following: Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ".
• 10232302Feb 2, 2023Steering, Wheels. Some vehicles may exhibit a steering shimmy or body vibration during the PDI test drive or during the first few miles of driving after the vehicle has been delivered to the customer due to flat spots on the tires. Flat spots on tires may be caused by improper maintenance during dealer storage (e.g.: Vehicle was left stationary for a prolonged period of time in high ambient temperatures).
• 10232402Feb 1, 2023Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
• 10230891Jan 31, 2023Engine cooling. Some vehicles may have a "LOW ENGINE OIL LEVEL" warning message and an engine oil level warning light on in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the…
• 10230866Jan 25, 2023Electrical system. Due to the supply chain shortages for BDGF-66-5G0G, hardware has been confirmed compatible between BDGF-66-5G0B up to the G suffix. This can be used for repair with vehicles originally equipped with C to G level suffix parts.
• 10230902Jan 23, 2023Body and structure. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10230880Jan 23, 2023Electrical system. Some customers may complain about the infotainment system and/or the MyMazda App showing incorrect clock and/or tire pressures and/or tire pressure missing. This may be caused by: - Incorrect calendar entry (month/day/year) after a battery disconnect - Infotainment system software update. - BCM TPMS unlearn during vehicle storage or transport. - Wheel/Tire change
• 10230865Jan 23, 2023Engine cooling. When servicing SKYACTIV engine vehicles requiring to replace the Oil Galley Plug and Crush Washer, order the required part numbers below. These parts are not listed in GEPC and were previously listed as "non-serviceable" in the cylinder block diagram.
• 10230878Jan 19, 2023Electrical system. Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 10230877Jan 13, 2023Latches, locks and linkages. Some customers may report hearing an unusual noise coming from the power liftgate (PLG) when it is unlatching to open or latching closed. This is caused by an internal fault in the liftgate latch and/or loose bolts holding the latch to the liftgate.
• 10230875Jan 11, 2023Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10230873Jan 6, 2023Exterior lighting. Some customers may complain about hearing noise from their headlamps. While some noise is normal from the electric motor, if it is louder in one headlamp than the other or both are significantly louder than a known good vehicle
• 10230894Jan 3, 2023Electrical system. Some vehicles may exhibit DTC U3000:04 (Telematics communication unit internal malfunction) stored after the connected service contract has been discontinued (only vehicles in which the customer opted out of CV services are affected - CSP04). This is caused by improper control software of telematics communication unit. To eliminate this concern, the control software of telematics communication unit has been modified.
• 10228661Dec 22, 2022Brakes. Some customers may complain about hearing a grinding noise and/or vibration occur when applying the brake. This is due to rust on the rear brake disc plate.
• 10228662Dec 21, 2022Visibility (wipers, defrost, mirrors), Electrical system. Some customers may complain the A/C blows warm. This may be caused by one of two things. Cause 1: After accelerating in hot weather, the A/C blows warm air for a longer time than other models. This is caused by improper control software of the PCM not allowing the A/C compressor to resume properly after acceleration. During a hard acceleration above a certain throttle level opening, the PCM stops the A/C compressor…
• 10228657Dec 20, 2022Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10228659Dec 19, 2022Engine cooling. Some vehicles may experience an engine stall when hard accelerating from a stop (often difficult to reproduce on a test drive), no codes are stored and the vehicle easily restarts with no other drivability concerns. This is only caused in certain situations by the torque reduction calibration in the PCM software. To correct this issue, the control software of the PCM has been modified to optimize the torque…
• 10228650Dec 14, 2022Electrical system. Customers having MAZDA CONNECT concerns should have their vehicle repaired using the following repair procedure.
• 10228653Dec 13, 2022Electrical system. MAZDA CONNECTED SERVICES Frequently Asked Questions (FAQ)
• 10228652Dec 13, 2022Electrical system. Some customers may complain about any of the following: * Infotainment Center Display does not provide the Authorization Code during the MyMazda App Connected Vehicle enrollment. * Remote function(s) inoperative. - Engine Start / Stop - Door Lock / Unlock - Lights ON / OFF * MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Confirm the customer's phone and vehicle have good to strong…
• 10228651Dec 7, 2022Equipment. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method
• 10228663Dec 1, 2022Body and structure. Some vehicles may experience white-streak stains appearing on the front door that look like they seeped out from under the outer mirror base. This is caused by water intruding from gaps of the outer mirror body and/or the hinge of the outer mirror, and corrosion occurring on the aluminum die-cast inner base in the outer mirror. Water, including white-salty corrosion, may drip out from gaps under the outer mirror…
• 10228648Dec 1, 2022Engine cooling. Some vehicles may experience the Check Engine Light ON with DTC P0171 (Fuel Trim too Lean) and possibly DTCs P030X (Misfire). Vehicles having this concern should use the following Inspection/Repair procedure.
• 10226856Nov 22, 2022Electrical system. Some customers may experience one or both of the following symptoms while locking and unlocking the doors works fine using the remote transmitter. - Symptom 1: The touch sensor of the front door outer handle does not lock the doors after rain and/or car washing, even though unlocking is possible. - Symptom 2: The touch sensor of the front door outer handle does not unlock the doors.
• 10226892Nov 21, 2022Electrical system. Some customers may experience that, with a specific operation, the touch sensor of front door outer handle does not lock and unlock the doors but the remote transmitter operates correctly. Description of the specific operations: - Specific Operation 1 [MX-30]: After using cabin preconditioning or hazard warning lights for approx.15 minutes. - Specific Operation 2 [MAZDA3 and CX-30]: After using hazard warning…
• 10226814Nov 18, 2022Suspension. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10226889Nov 15, 2022Electrical system, Seats. Some customers may complain that the seat warmer does not operate when turning the ignition on while the seat is warm but when turning the ignition off then on again, the seat warmer begins to operate appropriately. DTCs "B1030:13" and/or "B1032:13" are stored. This is caused by the seat warmer's fail-safe mode which prevents it from working during the initial drive cycle. To correct this issue, the seat warmer has…
• 10226924Nov 14, 2022Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices. Examples: 1. Devices connected to the…
• 10226923Nov 14, 2022Visibility (wipers, defrost, mirrors), Electrical system. Some customers may complain the HVAC system not maintaining the correct temperature or the ambient (outside) temperature reading incorrectly. This is caused by a failure in the ambient temperature sensor. To correct this issue, the ambient temperature sensor has been modified.
• 10226816Nov 7, 2022Engine cooling. Some vehicles may have a "LOW ENGINE OIL LEVEL" warning message and a CHECK ENGINE light illuminated in the instrument cluster with DTC P250F:00 stored in memory, and the oil level has actually decreased to near low. - DTC P250F:00 - Engine oil level signal: engine oil level low This is caused by an oil consumption increase due to damage of the valve seals on the exhaust side. To eliminate this concern, the design…
• 10226898Nov 4, 2022Electrical system. Some customers may complain that Mazda Connect does not start (blank screen) or that it takes a long time to restart/ reboot after starting the vehicle. This is caused by the initialization process with the CMU failing at startup due to a defective circuit board element. To eliminate this concern, the internal hardware (DRAM) of the CMU has been improved.
• 10226916Nov 2, 2022Electrical system. Some customers may comlpain about an intermittent Beep sound (popping sound) every 1 ~ 2 minutes while driving. This may be cause by a software error in the navigation SD card.
• 10226918Nov 1, 2022Electrical system. Some customers may complain about intermittent audio no sound from the MAZDA CONNECT infotainment system and/or static noise from the speakers. The concern may be reproduced by tapping on the dash pad near the MAZDA CONNECT center display and the following DTC's may be stored.
• 10226896Nov 1, 2022Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 7000C0A-NA01_12004 or later). Ver. 7000C0A-NA01_12004 fixes these software errors (bugs): * Album artwork may not appear when playing music using an USB connected iPhone. * The center display may turn black when the gear is shifted from reverse position to parking position. * Screen freezes and…
• 10225784Oct 28, 2022Visibility (wipers, defrost, mirrors). Some vehicles may exhibit windshield glass distortion or a double-image from the active driving display. These may be due to a) distortion in the windshield glass not properly removed during the manufacturing process or b) glass with incorrect specifications used in the manufacturing process. To eliminate these concerns, the windshield glass manufacturing process has been modified.
• 10225779Oct 19, 2022Equipment. Some customers may complain that the rear console lid does not slide smoothly. This may be caused by improperly positioned felt pads attached to the rear console lid lock, which may have moved out of position after repetitive use. The exposed adhesive residue may stick to the rail and disrupt smooth sliding operation. To eliminate this concern, the felt pad positions have been changed.
• 10225785Oct 17, 2022Electrical system. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Ver. 7000C0A-NA06_12012 or later).
• 10225767Oct 17, 2022Transmission and drivetrain. The new SKYACTIV-DRIVE FW6A-EL AT uses "Automatic Transmission Fluid (ATF) Type: FZ". Only use "ATF-FZ" to fill or top off the fluid level. ATF-FZ is specially designed for use in the SKYACTIV-DRIVE series AT. It is a low viscosity formula with less friction for better fuel economy. NOTE: ATF-FZ is colored blue for easy identification.
• 10225724Oct 17, 2022Body and structure. Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 10225763Oct 12, 2022Electrical system. Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less: * The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following: - The windshield is dirty - The FSC lens is foggy - There is low visibility due to rain…
• 10225761Oct 12, 2022Electrical system. Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: * C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles] * B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles built on or before March 2, 2019] * No DTC - Warning Message only [Gen 7…
• 10225778Oct 10, 2022Electrical system. Some customers may complain the A/C blows warm. This may be caused by one of two things. Cause 1: After accelerating in hot weather, the A/C blows warm air for a longer time than other models. This is caused by improper control software of the PCM not allowing the A/C compressor to resume properly after acceleration. During a hard acceleration above a certain throttle level opening, the PCM stops the A/C compressor…
• 10225751Oct 10, 2022Engine cooling. Some vehicles equipped with a coolant control valve may exhibit difficulties when refilling the coolant because the control valve is closed and air in the engine cannot escape during ignition ON. Therefore, turn the ignition OFF when refilling engine coolant using the radiator filler neck.

← All problems reported for the 2022 Mazda CX-30