2017 Mazda CX-5 Technical Service Bulletins

572 technical service bulletins (TSBs) are on record for the 2017 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10183601Nov 17, 2020Electrical system, Equipment. Some vehicles may exhibit a Connectivity Master Unit (CMU), a BLUETOOTH® hands-free unit or text messaging related concerns. To improve the handling of BLUETOOTH® hands-free and/or text messaging customer concerns, Mazda created a special service and parts exchange program as of February 2010.
• 10183634Nov 13, 2020Equipment, Engine cooling. MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports…
• 10183633Nov 10, 2020Engine cooling, Equipment. MULTI-MODEL - MAZDA MOBILE START CUSTOMER SATISFACTION PROGRAM. As shared previously, due to planned industry-wide changes in mobile network infrastructure and wireless technology, the Mazda Mobile Start (MMS) accessory was no longer offered beginning with 20MYvehicles. These technology changes are scheduled to occur in late 2021 as our service provider transitions away from a 3G network which currently supports…
• 10183604Nov 10, 2020Engine cooling. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary: Engine Oil Consumption Inspection Guideline 1. Record the vehicle mileage. 2. Engine at normal operating temperature, top off engine oil level to the full mark on the dipstick. 3. Ask the customer to return to the dealer after…
• 10183590Nov 9, 2020Equipment, Brakes. Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake…
• 10183592Nov 3, 2020Transmission and drivetrain. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise:  Depends on the vehicle’s speed only (the more speed, the more noise)  Occurs with all types of driving (acceleration, deceleration, steady speed)  Does not depend on rpm, gear, or ATF temperature
• 10182123Oct 28, 2020Engine cooling, Equipment. Currently, the instructions on MGSS recommend the use of Loctite 962T or equivalent when installing a SKYACTIV cylinder head, but it is no longer available. The following 3 adhesives are alternatives available as an equivalent to Loctite 962T: Loctite 272, Loctite 518 Threebond TB-1386H
• 10182122Oct 15, 2020Electrical system, Equipment. APPLE CARPLAY / ANDROID AUTO FREQUENTLY ASKED QUESTIONS (FAQ): NOTE: The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS - Infotainment - MAZDA CONNECT Updates - Apple Carplay / Android Auto MDARS Activation Instructions
• 10182126Oct 14, 2020Equipment, Engine cooling. CRACKED REAR DIFFERENTIAL: Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
• 10182121Oct 12, 2020Equipment. ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.mazdausa.com
• 10182094Oct 12, 2020Brakes. Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake…
• 10180597Sep 25, 2020Suspension. Some customers may complain about oil seepage or oil leakage from the rear shock absorbers. This concern may be due to a lack of sealing performance. To eliminate the oil seepage/leakage, the rear shock absorbers production process has been modified.
• 10180667Sep 15, 2020Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.367 or later).
• 10180599Sep 8, 2020Steering. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
• 10180670Sep 4, 2020Electrical system, Equipment, Steering, Brakes, Visibility (wipers, defrost…. Some vehicles may exhibit that the SBS/SCBS warning light (amber) turns ON right after the engine is started with DTC U0420:68 [FSC] stored in memory.  DTC U0420:68 [Forward sensing camera (FSC)]: Error signal received from electric power steering (EPS) control module. For Mazda6 and CX-5, the following error messages may appear in the instrument cluster.
• 10180666Sep 3, 2020Body and structure, Equipment. Some vehicles may exhibit poor fitting rear door weatherstrips at the lower/front location. The weatherstrips may be deformed by frequent contact with passengers entering and exiting the vehicle, causing the weatherstrip joint to become enlarged. The enlarged weatherstrip joint does not grip the door panel tight enough when it is refitted.
• 10180665Sep 3, 2020Equipment, Body and structure. Some vehicles may have a loose rear bumper reflector without any visible external damage to the rear bumper cover. Due to an external force applied to the bumper cover, one of the brackets fastening the reflector to the bumper cover may have become detached.
• 10179080Aug 25, 2020Steering. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
• 10179315Aug 18, 2020Electrical system. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
• 10179313Aug 13, 2020Brakes, Forward collision avoidance, Equipment, Visibility (wipers, defrost…. Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less:  The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following:  The windshield is dirty  The FSC lens is foggy  There is low…
• 10179154Aug 7, 2020Electrical system. Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory:  U3003:16 (Power liftgate (PLG) control module power supply voltage low input)  U3003:17 (Power liftgate (PLG) control module power supply voltage high input). This may be caused by low or high vehicle battery voltage.
• 10179228Aug 3, 2020Tires, Wheels. New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
• 10177845Jul 21, 2020Steering, Electrical system. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
• 10177847Jul 20, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10177853Jul 15, 2020Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10177843Jul 9, 2020Equipment, Engine, Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been…
• 10177005Jun 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10177012Jun 10, 2020Transmission and drivetrain. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order…
• 10176975Jun 10, 2020Electrical system, Air bags. Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low.  DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily.
• 10176977Jun 3, 2020Equipment, Electrical system. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the…
• 10176054May 11, 2020Visibility (wipers, defrost, mirrors). Some vehicles may experience an engine no start/no crank with either of the following DTC's stored: P0615:12 - Starter relay circuit malfunction B112A:12 - IG2 relay circuit malfunction. This may be caused by water contamination/corrosion at electrical connector C-04 due to: Windshield tint installation: Windshield tint installed to block UV light. The water used during the installation of the tint may run down…
• 10174589Apr 29, 2020Electrical system, Latches, locks and linkages, Equipment. Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from condensation may drip onto the switch connector and cause corrosion.
• 10174690Apr 28, 2020Transmission and drivetrain. Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
• 10174583Apr 17, 2020Electrical system, Equipment. Some customers may experience the MAZDA CONNECT rebooting or the screen turning black during cold temperatures. The concern occurs when the interior of the vehicle is cold and disappears when the interior warms up. This is caused by some SD cards for the MAZDA CONNECT navigation system being manufactured with improper hardware, resulting in a data reading error during cold temperatures. To correct the concern, the…
• 10174570Apr 1, 2020Steering. Some vehicles may exhibit an unusual noise (clacking) from under the front of the vehicle. This noise only occurs when starting to move the vehicle while the steering wheel is fully turned to the driver-side (left side for LHD vehicle and right side for RHD vehicle). NOTE: The noise will not occur if the steering wheel is in the center or to the full passenger-side position. The noise is caused when the edge (A) of…
• 10173097Mar 12, 2020Transmission and drivetrain, Brakes, Engine cooling, Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10173253Mar 11, 2020Electrical system, Equipment. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10173100Mar 6, 2020Brakes, Equipment. Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.
• 10173228Mar 4, 2020Equipment. The owner’s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts.
• 10173249Mar 3, 2020Forward collision avoidance, Equipment. Some vehicles may have one of the following DTCs stored in memory:  C1001:92 - Forward sensing camera (FSC) poor field of view  B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect.  In some cases the customer may have a concern with…
• 10171836Feb 28, 2020Equipment. DTC P0942:49 TROUBLESHOOTING: P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added to the Workshop Manual.
• 10171849Feb 27, 2020Equipment. Some customers may complain about a high frequency noise (like a mosquito sound) while the active driving display is in the flip-up position. The noise may be coming from the capacitor inside the active driving display which vibrates according to the display control frequency. The circuit board resonates with it resulting in an audible noise. To eliminate this concern, the active driving display has been modified…
• 10171843Feb 26, 2020Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10171792Feb 26, 2020Transmission and drivetrain. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
• 10171844Feb 20, 2020Brakes. Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc…
• 10171780Feb 18, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10171787Feb 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth®, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.
• 10170941Jan 29, 2020Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10170814Jan 23, 2020Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
• 10170813Jan 23, 2020Equipment, Electrical system. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem  P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service…

← All problems reported for the 2017 Mazda CX-5