2017 Mazda CX-5 Technical Service Bulletins

572 technical service bulletins (TSBs) are on record for the 2017 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10170943Jan 15, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10170829Jan 15, 2020Electrical system, Body and structure, Engine cooling. LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10170817Jan 13, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
• 10170825Jan 10, 2020Equipment, Engine cooling. THUMPING/RATTLING NOISE FROM ENGINE COMPARTMENT: Some customers may complain about an unusual thumping/rattling noise coming from the engine compartment. The noise is most pronounced under the following conditions:  Engine at idle  Transmission in drive  Foot on the brake pedal  A/C OFF  Audio OFF The noise may be caused by loose fitting heater hoses vibrating the heater hose bracket…
• 10170661Jan 9, 2020Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement.  Mazda vehicles are…
• 10170656Jan 9, 2020Suspension, Equipment. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10170660Jan 8, 2020Seats, Equipment. Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. This is caused by a gap between the leather seat surface and the seat cushion pad due to insufficient tension on the seat trim. To eliminate this concern, a non-woven fabric has been attached to the backside of the seat trim to increase tension.
• 10169542Dec 19, 2019Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).
• 10169540Dec 19, 2019Equipment, Engine cooling. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold.
• 10169513Dec 18, 2019Other or unknown, Transmission and drivetrain. WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
• 10169539Dec 17, 2019Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is…
• 10169543Dec 13, 2019Equipment, Visibility (wipers, defrost, mirrors), Other or unknown. Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window…
• 10169537Dec 13, 2019Engine cooling, Equipment. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10169509Dec 5, 2019Transmission and drivetrain, Engine cooling. GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a…
• 10168785Nov 26, 2019Engine cooling. Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.
• 10168139Nov 20, 2019Engine cooling, Equipment, Electrical system. Some customers may complain about:  Intermittent engine no start  Instrument cluster red security indicator light ON  Engine Start/Start Button Amber indicator light flashing  Battery discharge  Electrical relay buzzing noise  DTC B13D3:94 (Communication error with remote transmitter) stored.This may be caused by:  A key in a purse near a cell phone. The cell phone radio…
• 10168118Nov 20, 2019Engine cooling, Electrical system, Equipment. Some customers may complain about a Mazda Mobile Start (MMS) system malfunction. Use the information below to troubleshoot the customers complaint:  MAZDA MOBILE START (MMS) TROUBLESHOOTING GUIDE  CANNOT COMMUNICATE WITH VEHICLE  ERROR MESSAGE INSTALLED ON ANDROID DEVICES  COMMUNICATION ERRORS  MMS CHECK MODE - Use to verify system operation (see below).
• 10168098Nov 14, 2019Engine cooling, Equipment. Some customers may complain about a vibration through the driver and passenger seats at idle in (D)rive and (R)everse when the engine rpm drops down to 550. This vibration is caused by: 1.5L The No.3 and No.4 engine mount rubber hardening during vehicle usage at high ambient temperatures which decreases the damping force.
• 10168072Nov 4, 2019Electrical system, Engine, Equipment. Some customers may complain about poor heater performance even after the engine reaches normal operating temperature. This may be caused by a plugged heater core. For 2014-2016 Mazda6 and 2013-2016 (US spec) / 2017 (Mexico spec) CX-5, the CHECK ENGINE light may turn on with DTC P011A:00 (ECT sensor No.1/No.2 performance problem) stored at the same time. NOTE: Refer to TSB 01-015/15 if the customer is using a block…
• 10166848Oct 8, 2019Engine cooling. Some customers may complain about high engine oil consumption. Before attempting any repairs, verify the complaint by using the guideline below to determine if an engine repair is necessary:
• 10165676Sep 30, 2019Engine cooling. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold.
• 10165341Sep 16, 2019Brakes. Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.
• 10165350Sep 6, 2019Engine cooling, Body and structure. Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10164279Aug 30, 2019Body and structure. Some vehicles may exhibit cracking (1) at the lower part of the rear side, rear door garnish (2). This concern is caused by excess stress applied to the rear door garnish. To eliminate this concern, the clip and tape position on the rear door garnish has been improved.
• 10164267Aug 23, 2019Engine cooling. Some vehicles may experience a rough idle with the check engine light on and DTC P0015 / P0524 stored in memory. P0015:00 - Exhaust CMP timing over-retarded. P0524:00 - Engine oil pressure too low. This is caused by a drop in engine oil pressure due to a piece of foreign object stuck on the oil pump pressure relief valve or oil control valve (OCV). The temporary entry of the foreign object triggers a check engine…
• 10164045Aug 16, 2019Back-over prevention (rear camera). Some customers may experience improper operation of the rear parking system with beep sounds coming from the rear parking sensor when there are no obstacles behind the vehicle. This occurs when the blower fan is on (at any fan speed) and the transmission is in "R" position. The concern is caused by electrical noise from the blower fan controller circuit affecting the rear parking sensor circuit.
• 10163826Aug 12, 2019Seats. Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. This is caused by a gap between the leather seat surface and the seat cushion pad due to insufficient tension on the seat trim. To eliminate this concern, a non-woven fabric has been attached to the backside of the seat trim to increase tension.
• 10163827Aug 7, 2019Electrical system, Equipment. After the installation of a new instrument cluster, the message "Fctry" or “Factory” is displayed instead of the odometer. This concern may also occur when a room fuse is installed in a new vehicle. Some new instrument clusters are in the factory mode setting. Factory mode cancellation is required. NOTE: The concern is applicable to Calsonic Kansei instrument clusters. Not all trim levels are…
• 10163825Aug 7, 2019Exterior lighting, Brakes, Electrical system, Visibility (wipers, defrost…. Some customers may experience one or more electrical malfunctions after a vehicle body repair. The newly painted fender stay (2) may be causing a poor front harness (1) ground connection.The front fender stay (2) newly painted surface at ground point (3), where attachment bolt (4) is seated, may create a poor front harness ground connection. Customers concern can be resolved by sanding off paint at ground point (3)…
• 10163334Jul 31, 2019Equipment. The database error discovered with IDS 114.00-114.02 release has been fixed with IDS 114.04 release and is now available for download.
• 10163327Jul 30, 2019Forward collision avoidance. Some vehicles may have one of the following DTCs stored in memory: C1001:92 - Forward sensing camera (FSC) poor field of view. B14F0:92 - General temporary failure in forward sensing camera (FSC). DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect. In some cases the customer may have a concern with the Lane Departure…
• 10163356Jul 26, 2019Electrical system, Equipment. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10163367Jul 16, 2019Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. "Mazda Air Cooling Coil Coating" is available…
• 10163333Jul 9, 2019Electrical system, Equipment. Due to a database error discovered with IDS 114.00-114.02 release (which affects Recall 3719F), it will be necessary to uninstall IDS 114 and install IDS 113.00 and 113.06 update. The Recall can be performed after removing IDS 114 and installing IDS 113. This SA will be updated when more information is available.
• 10162012Jun 27, 2019Wheels, Tires. Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold).
• 10162027Jun 25, 2019Equipment. ACCESSORY INSTRUCTIONS LOCATION: Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/
• 10162014Jun 6, 2019Electrical system, Equipment. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.335C or later). NOTE:For 2016 CX-9 with version earlier than 59.00.441, the tachometer function will be removed from the Active Driving Display as part of Mazda’s continuing efforts to improve safety and reduce driver distraction. Please explain this to the customer before updating the…
• 10160556May 23, 2019Steering. Some customers may notice the heated steering wheel shuts off by itself after approx. 5 - 7 minutes after turning it on. The heated steering wheel is designed to stay on for 30 minutes before shutting off by itself. This may be due because the temperature around the thermostat is greatly increased due to the incorrect positioning of the steering wheel heating element. This results in the electrical supply to the…
• 10160555May 20, 2019Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on P0877:00 - Oil…
• 10160551May 2, 2019Engine cooling. Some vehicles may experience a lack of power and the check engine light on with DTC P61B:00 stored in the PCM memory when driving in high temperatures at high elevations. DTC P061B:00 - [PCM] Internal control module torque calculation performance problem This concern may be caused by improper PCM control logic. The engine torque calculation error may increase in high temperatures at high elevations. To eliminate…
• 10160575May 1, 2019Electrical system, Equipment, Back-over prevention (rear camera). Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the flowchart below to repair the vehicle.
• 10159280Apr 30, 2019Seats. Some customer may complain of warping on the driver seat cushion trim, which may cause poor appearance complaints. This is caused by a gap between the leather seat surface and the seat cushion pad due to insufficient tension on the seat trim. To eliminate this concern, a non-woven fabric has been attached to the backside of the seat trim to increase tension.
• 10159277Apr 25, 2019Tires, Wheels. Some vehicles may experience the TCS/DSC indicator light and the TPMS warning light both ON with DTC C0051:62 stored in memory. DTC C0051:62 - The difference between the initial learned value of the steering angle (as calculated by each sensor) and the steering angle (as calculated by the steering angle sensor) while driving in a straight line, has exceeded its allowable tolerance (or threshold).
• 10159204Apr 8, 2019Suspension, Wheels. There have been warranty claims submitted for noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
• 10159198Apr 5, 2019Equipment, Electrical system. Apple carplayã¢â„⢠/ android autoã¢â„⢠frequently asked questions (faq)
• 10159201Apr 1, 2019Equipment. MAZDA IDS INOPERATIVE WITH VCM-II LICENSE EXPIRATION MESSAGE - If you encounter an IDS inoperative problem with VCM-II license expiration message, follow the instructions below: 1. CLICK HERE to download the resetting tool to your PC desktop. 2. Reboot your PC, DO NOT start any application after restarting. 3. Run the resetting tool by double clicking the "Reset.bat" file (on your desktop from step 1). 4. Press any…
• 10155442Mar 27, 2019Equipment, Electrical system. APPLE CARPLAY™ / ANDROID AUTO™ FREQUENTLY ASKED QUESTIONS (FAQ). Many frequently asked question and the answers.
• 10155441Mar 27, 2019Body and structure. Some customers may complain that the rear door seaming welt (1) comes off when stepping in and/or out of the vehicle. This is caused by the gripping force of the seaming welt being insufficient for frequent usage of the rear seat (vehicle used for ride sharing). No mass production change is planned.
• 10155437Mar 27, 2019Transmission and drivetrain. Some customers may complain of a whining noise from the automatic transaxle when driving at 10 mph and above. The noise: Depends on the vehicle’s speed only (the more speed, the more noise)Occurs with all types of driving (acceleration, deceleration, steady speed)Does not depend on rpm, gear, or ATF temperature.This is caused by a damaged bearing in the transaxle due to improper configuration…
• 10155440Mar 22, 2019Exterior lighting, Brakes, Forward collision avoidance, Equipment, Lane…. Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction).Master Warning Light, Smart Brake Support/Smart City Brake Support (SBS/SCBS) Indicator Light, Lane-keep Assist System (LAS) Lane Departure Warning System (LDWS) Warning Light, High Beam Control (HBC)…

← All problems reported for the 2017 Mazda CX-5