2018 Mazda CX-5 Technical Service Bulletins

634 technical service bulletins (TSBs) are on record for the 2018 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10179080Aug 25, 2020Steering. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
• 10179172Aug 20, 2020Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.
• 10179315Aug 18, 2020Electrical system. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the GR8 battery charger SST to maintain battery voltage.
• 10179313Aug 13, 2020Brakes, Forward collision avoidance, Equipment, Visibility (wipers, defrost…. Some customers may complain about the following message displayed in the Multi-Information Display: In the following cases, the MRCC with Stop & Go function system is canceled when the vehicle is traveling at 19 mph (30 km/h) or less:  The Forward Sensing Camera (FSC) cannot detect target objects due to one of the following:  The windshield is dirty  The FSC lens is foggy  There is low…
• 10179154Aug 7, 2020Electrical system. Some customers may complain about an inoperative power liftgate (PLG) and the any of the following DTC's stored in memory:  U3003:16 (Power liftgate (PLG) control module power supply voltage low input)  U3003:17 (Power liftgate (PLG) control module power supply voltage high input). This may be caused by low or high vehicle battery voltage.
• 10179177Aug 5, 2020Engine cooling. If you receive a customer concern about the CHECK IN light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, perform the inspection in the Repair Procedure.
• 10179170Aug 5, 2020Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. NOTE: Cylinder head replacement requires MASH authorization.
• 10179228Aug 3, 2020Tires, Wheels. New CARB regulation regarding mandatory checking and documenting of tire pressure whenever a vehicle is in for service work. This applies to all service shops (including Mazda dealerships) in California effective September 1, 2010.
• 10177956Jul 24, 2020Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats and cotters (IN/EX) are included in the new assembly.
• 10177845Jul 21, 2020Steering, Electrical system. Some customers may complain of a steering wheel vibration (in a rotational direction), when they are not holding onto the steering wheel. The vibration stops when holding onto the steering wheel or when driving. This may be caused by improper control logic of the EPS control module. To eliminate this concern, the EPS control logic has been modified.
• 10177847Jul 20, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Paint Warranty Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable).
• 10177853Jul 15, 2020Electrical system, Equipment. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed. Below are a couple of examples of unusual electrical concerns caused by aftermarket devices.
• 10177937Jul 9, 2020Engine cooling, Brakes. If a customer comes in with the following concerns:  OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON.  DTC P055F and/or P0524 stored.  No driveability concern or engine mechanical noise.  Outside the VIN range in TSB 01-020/18.
• 10177843Jul 9, 2020Equipment, Engine, Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). This is caused by the oil pressure switch A and/or B at the control valve body temporarily or permanently getting stuck due to contamination entering the passage. To correct the problem, some mass production changes have been…
• 10177015Jun 22, 2020Engine cooling. If a customer comes in with the following concerns, perform the inspection procedure.  OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON.  DTC P055F and/or P0524 stored.  No driveability concern or engine mechanical noise.  Outside the VIN range in TSB 01-020/18.
• 10177005Jun 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10177012Jun 10, 2020Transmission and drivetrain. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order…
• 10176975Jun 10, 2020Electrical system, Air bags. Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low.  DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily.
• 10176054May 11, 2020Visibility (wipers, defrost, mirrors). Some vehicles may experience an engine no start/no crank with either of the following DTC's stored: P0615:12 - Starter relay circuit malfunction B112A:12 - IG2 relay circuit malfunction. This may be caused by water contamination/corrosion at electrical connector C-04 due to: Windshield tint installation: Windshield tint installed to block UV light. The water used during the installation of the tint may run down…
• 10174589Apr 29, 2020Electrical system, Latches, locks and linkages, Equipment. Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from condensation may drip onto the switch connector and cause corrosion.
• 10174690Apr 28, 2020Transmission and drivetrain. Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
• 10174567Apr 23, 2020Engine cooling. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.
• 10173225Mar 27, 2020Transmission and drivetrain, Engine cooling. A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500 -3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an…
• 10173097Mar 12, 2020Transmission and drivetrain, Brakes, Engine cooling, Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10173253Mar 11, 2020Electrical system, Equipment. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10173227Mar 11, 2020Engine cooling. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms:  The engine takes longer to warm up.  The engine temperature gauge fluctuates.  The low coolant temperature indicator (blue) light stays on longer or comes on while driving.  Poor heater performance, especially at idle.
• 10173100Mar 6, 2020Brakes, Equipment. Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.
• 10173228Mar 4, 2020Equipment. The owner’s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts.
• 10173249Mar 3, 2020Forward collision avoidance, Equipment. Some vehicles may have one of the following DTCs stored in memory:  C1001:92 - Forward sensing camera (FSC) poor field of view  B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect.  In some cases the customer may have a concern with…
• 10171840Feb 28, 2020Engine cooling. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.
• 10171836Feb 28, 2020Equipment. DTC P0942:49 TROUBLESHOOTING: P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added to the Workshop Manual.
• 10171843Feb 26, 2020Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10171792Feb 26, 2020Transmission and drivetrain. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
• 10171844Feb 20, 2020Brakes. Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc…
• 10171780Feb 18, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10171841Feb 13, 2020Engine cooling. Some customers may experience a check engine light illumination with DTCs P24C6:00, P24AE:00, P24B1:00 and/or P24AF:00 stored in PCM memory.
• 10171787Feb 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth®, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.
• 10171786Feb 11, 2020Equipment, Electrical system, Engine cooling. A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500-3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an…
• 10170941Jan 29, 2020Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10170814Jan 23, 2020Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
• 10170813Jan 23, 2020Equipment, Electrical system. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem  P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service…
• 10170943Jan 15, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10170829Jan 15, 2020Electrical system, Body and structure, Engine cooling. LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10170819Jan 13, 2020Equipment, Body and structure. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.
• 10170818Jan 13, 2020Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
• 10170817Jan 13, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
• 10170825Jan 10, 2020Equipment, Engine cooling. THUMPING/RATTLING NOISE FROM ENGINE COMPARTMENT: Some customers may complain about an unusual thumping/rattling noise coming from the engine compartment. The noise is most pronounced under the following conditions:  Engine at idle  Transmission in drive  Foot on the brake pedal  A/C OFF  Audio OFF The noise may be caused by loose fitting heater hoses vibrating the heater hose bracket…
• 10170661Jan 9, 2020Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement.  Mazda vehicles are…
• 10170656Jan 9, 2020Suspension, Equipment. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10170660Jan 8, 2020Seats, Equipment. Some customer may complain of warping on the driver and/or passenger side seat cushion trim, which may cause poor appearance complaints. This is caused by a gap between the leather seat surface and the seat cushion pad due to insufficient tension on the seat trim. To eliminate this concern, a non-woven fabric has been attached to the backside of the seat trim to increase tension.

← All problems reported for the 2018 Mazda CX-5