2018 Mazda CX-5 Technical Service Bulletins

634 technical service bulletins (TSBs) are on record for the 2018 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10202772Oct 13, 2021Equipment, Transmission and drivetrain, Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.
• 10202695Oct 13, 2021Fuel system, Other or unknown. Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline. E85: A blend of 85% ethanol and 15% gasoline All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than 10%…
• 10202689Oct 8, 2021Equipment, Electrical system, Visibility (wipers, defrost, mirrors). Some vehicles may exhibit insufficient A/C performance / insufficient airflow from vents or ducts. These concerns may be caused by an evaporator temperature sensor malfunction due to insufficient water-proofing. This may result in a detection error and therefore, improper operation of the A/C system. To eliminate this concern, the production process of the evaporator temperature sensor has been modified to ensure…
• 10201864Sep 28, 2021Equipment, Electrical system. MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10201766Sep 27, 2021Engine cooling, Equipment. Some customers may experience the CHECK ENGINE light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up, The engine temperature gauge fluctuates, The low coolant temperature indicator (blue) light stays on longer or comes on while driving, Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable.
• 10201777Sep 24, 2021Equipment, Engine cooling. Ethanol is becoming a common additive in gasoline. Gasoline containing ethanol is likely available at your local gasoline station. Typical blends of ethanol include E10 and E85. E10: A blend of 10% ethanol and 90% gasoline, E85: A blend of 85% ethanol and 15% gasoline, All Mazda vehicles can run on gasoline containing up to 10% ethanol (E10) but only some 1999-2001 B3000 trucks can run on gasoline with more than…
• 10201776Sep 24, 2021Visibility (wipers, defrost, mirrors), Equipment, Electrical system, Lane…. Some vehicles equipped with Blind Spot Monitoring (BSM) may experience a BSM indicator light on the outer door mirror, even if there is no vehicle in the alert (blind spot) area. NOTE: This concern occurs only after a cold start. As the BSM control module temperature rises, the BSM system returns to normal operation.
• 10201775Sep 17, 2021Body and structure, Equipment. Some customers may complain about a whistling noise heard from the top of the A-pillar area when driving at highway speeds. When driving under following conditions, a negative pressure is generated on the doors pulling them outward and resulting in weatherstrip vibration. The vehicle is exposed to a side wind while driving at highway speeds. The vehicle is exposed to a strong side wind while driving at a speed…
• 10201861Sep 16, 2021Engine cooling. If you receive a customer concern about the CHECK ENGINE light coming on and DTC P3400 (cylinder deactivation system malfunction) stored, the cylinder deactivation oil control valve may be plugged with plastic debris from the oil filter wrapper. The debris may enter the center of the oil filter when poking a hole in the filter wrapper during removal, and then travel through the engine and plug the cylinder…
• 10201772Sep 13, 2021Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 74.00.230 or later).
• 10201771Sep 13, 2021Equipment, Body and structure. Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation (door opening/closing and vibration while driving).
• 10201767Sep 13, 2021Equipment, Brakes. Some vehicles may exhibit: Vehicle body vibration when moving from a stop while using the Electric Parking Brake (EPB) automatic release function. Uneven rear brake pad wear. These concerns may be caused because the automatic EPB caliper release timing is too late for the movement of the vehicle. NOTE: Frequent usage of the EPB automatic release function may promote uneven rear brake pad wear. To eliminate these…
• 10201770Sep 10, 2021Engine cooling, Equipment. Some vehicles may exhibit a squeaking noise from the blower motor while it is operating. This is caused by burrs that were not trimmed completely in the manufacturing process of the blower motor. To eliminate this concern, the manufacturing process of the blower motor has been modified to efficiently trim burrs.
• 10201768Sep 3, 2021Transmission and drivetrain. Some vehicles may experience the check engine light and automatic transaxle warning light ON with one or more of these DTCs stored in the TCM memory (P0842, P0847, P0872, P0877, P0780, P1738). P0842:00 - Oil pressure switch No. 1 (oil pressure switch B) stuck on, P0847:00 - Oil pressure switch No. 2 (oil pressure switch A) stuck on, P0872:00 - Oil pressure switch No. 3 (oil pressure switch A) stuck on, P0780:00…
• 10201863Sep 1, 2021Equipment, Electrical system. MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10200933Aug 24, 2021Electrical system, Engine cooling. This service bulletin provides testing and charging procedures in order to promote proper battery maintenance, to deliver new vehicles with fully charged batteries, and to reduce unnecessary battery replacement cost. For new vehicles in stock at the dealer, inspect and maintain the battery periodically according to the repair procedure.
• 10200527Aug 17, 2021Equipment. This service bulletin provides information regarding the proper use of the driver’s floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
• 10200940Aug 10, 2021Equipment, Electrical system. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10200528Aug 6, 2021Equipment. AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest…
• 10200939Aug 5, 2021Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly.
• 10199714Jul 19, 2021Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains or discoloration.
• 10199715Jul 12, 2021Body and structure. Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation (door opening/closing and vibration while driving). NOTE: If the rust/paint peeling is seen on the outer side of the door, this service bulletin does not apply.
• 10199641Jul 9, 2021Electrical system, Equipment. Some customers may experience a SBS/SCBS, LAS/LDWS and/or HBC warning light on. A system error message may also be found in the center display. DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction). DTC U3000:04-0A (Forward sensing camera (FSC) internal malfunction) is stored in the FSC module and cannot be erased. This concern may be caused by a hardware failure of an internal device of the FSC…
• 10199634Jul 8, 2021Equipment. AUDIO, NAVIGATION AND PHONE CONCERNS WITH MAZDA CONNECT INFOTAINMENT SYSTEM (6TH GENERATION). All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest…
• 10198679Jun 25, 2021Electrical system, Equipment. MAZDA CONNECT SYMPTOM TROUBLESHOOTING [6TH GENERATION VEHICLES]. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10198685Jun 24, 2021Air bags. Some customers may complain that the passenger seat belt warning light is ON and the PASS AIRBAG OFF indicator light is OFF with no front passenger in the seat. This may be caused by an electrical device (smart phone, tablet, laptop. etc.) placed on the front passenger's seat.
• 10198673Jun 15, 2021Equipment. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method B. Auxiliary Key Code Cut Method A. Auxiliary Key Trace Cut Method If only one auxiliary key is lost/missing, some key cutting machines can trace cut a new key blank. 1. Trace cut the new auxiliary key blank(s). B. Auxiliary Key Code Cut Method If both auxiliary keys are lost/missing, use this method for cutting…
• 10198689Jun 9, 2021Equipment. Accessory instructions can be found on OneMazda under Dealer Resources - Parts & Accessories. The links provided below can be used for quick access: For 2016 models and newer: NOTE: Instructions are found under the "Attachments" section once a part is selected. Accessories E-catalog For models prior to 2016: Accessory Parts and Installation Instructions
• 10198691Jun 7, 2021Visibility (wipers, defrost, mirrors). Some vehicles may experience exterior trim heat damage when parked near a glass building or Low-E windows. This may be caused by the sun's reflection.
• 10198677Jun 4, 2021Equipment, Electrical system. APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay / Android Auto, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions
• 10198568Jun 4, 2021Brakes. Some vehicles equipped with electric parking brake (EPB) may exhibit a grinding noise from the rear brakes when braking. This may be caused by the rear brake pads not having the capability to remove the rust from the rear brake discs. The red rust accumulated on the discs is exposed to high temperatures during braking, and consequently the rust turns black. As the black rust is too hard to be removed by the brake…
• 10198574Jun 1, 2021Visibility (wipers, defrost, mirrors). Some vehicles may experience exterior trim heat damage when parked near a glass building. This may be caused by the suns reflection. If a building creates enough of a curve with a series of flat windows, which act like mirrors, the reflections all converge at one point, focusing and concentrating the light onto the street below.
• 10194656May 27, 2021Body and structure. Some vehicles may exhibit rust or paint peeling at the inside edge of the front door(s). This may be caused by dust adhering between the front door edge and the rear door weatherstrip, which rubs/damages the paint during vehicle operation (door opening/closing and vibration while driving). NOTE: If the rust/paint peeling is seen on the outer side of the door, this service bulletin does not apply.
• 10194655May 25, 2021Latches, locks and linkages, Electrical system. Some CX-5 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.
• 10194887May 18, 2021Equipment, Lane departure, Exterior lighting, Forward collision avoidance. Some vehicles may have one of the following DTCs stored in memory along with a system status notice on the Multi-information display OR display a system status notice with no DTC: C1001:92 - Forward sensing camera (FSC) poor field of view [Gen 6 vehicles], B14F0:92 - General temporary failure in forward sensing camera (FSC) [Gen 7 vehicles build on or before March 2, 2019], No DTC - Gen 7 vehicles built after March…
• 10194891May 13, 2021Equipment. When performing vehicle services such as control unit software update, control unit registration/activation, CMU log data retrieval, etc., always use the DCA8000 OR GR8 battery charger SST to maintain battery voltage.
• 10194782May 11, 2021Transmission and drivetrain. The rear differential case could develop a crack in the case, as shown below. NOTE: This could affect new vehicles just delivered to the dealer as well as customer vehicles.
• 10194714May 11, 2021Transmission and drivetrain. There have been warranty claims submitted for growling or bearing whine noise in differentials, transfer units and transmissions where the source of the noise was a wheel bearing. This misdiagnosis can lead to multiple repair attempts, warranty debits, and additional inconvenience and/or cost to the customer. To reduce the chance of this occurring, please follow the steps outlined in the repair procedure.
• 10194659May 7, 2021Engine cooling, Equipment, Electrical system. When programming a key or installing a Genuine Mazda Accessory Remote Engine Start system, you may encounter programming difficulty. This may be caused by a customer installed aftermarket decorative trim and/or cover on the START/STOP ENGINE button. The aftermarket accessory may create electrical interference, which may interfere with programming.
• 10194765May 6, 2021Engine cooling. A new cylinder head assembly for service parts has been newly established for SKYACTIV-G 2.5 with cylinder deactivation when replacement is needed. Valves, valve springs, valve spring seats, and cotters (IN/EX) are included in the new assembly. DUE TO A SUPPLY ISSUE FOR CYLINDER HEADS, GASKET SETS, AND PARTIAL ENGINE, PLEASE CONTACT HOTLINE FOR REPAIR GUIDANCE.
• 10194657May 5, 2021Equipment, Engine cooling, Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.
• 10194762May 4, 2021Equipment. Auxiliary key blank cutting procedure: There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method, B. Auxiliary Key Code Cut Method
• 10191535Apr 30, 2021Engine cooling. Some vehicles may have the check engine light on with DTC P0524:00 or P055F:00 stored in memory. Contamination in the engine oil may cause the engine oil solenoid valve to become stuck, resulting in improper operation of the oil pump and improper oil pressure. DTC P0524:00 (Engine oil pressure too low), DTC P055F:00 (Engine oil pressure malfunction). The control software of the PCM has been modified to eliminate…
• 10191534Apr 30, 2021Engine cooling. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it. To eliminate this concern, the switchable HLA has been modified for increased oil supply to reduce air bubbles in the oil passage.
• 10191538Apr 26, 2021Equipment. APPLE CARPLAY / ANDRID AURO FREQUENTLY ASKED QUESTIONS (FAQ) The following vehicles are not equipped with Apple CarPlay™ / Android Auto™, but it can be activated using MDARS. See Activation instructions on MGSS -> Infotainment -> MAZDA CONNECT Updates -> Apple Carplay / Android Auto MDARS Activation Instructions
• 10190956Apr 22, 2021Engine cooling. Some customers may experience the CHECK ENGINE light ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up, The engine temperature gauge fluctuates, The low coolant temperature indicator (blue) light stays on longer or comes on while driving, Poor heater performance, especially at idle. NOTE: Vehicles with SKYACTIV-G 2.5T are not applicable.
• 10190971Apr 8, 2021Equipment. MAZDA CONNECT Symptom Troubleshooting (6th Generation Vehicles). Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10190952Apr 2, 2021Transmission and drivetrain. Some vehicles may experience a lack of power and the check engine light on with DTC P061B:00 stored in PCM memory under one of the following conditions (A or B). DTC P061B:00 - [PCM] Internal control module torque calculation performance problem. Due to an improper control logic of the PCM, the engine torque calculation error detection is too sensitive. To eliminate this concern, the PCM software has been modified.
• 10189820Mar 25, 2021Electrical system. Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily.
• 10189797Mar 15, 2021Electrical system. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal Workshop Manual diagnosis. Aftermarket devices may be the cause of the electrical concern. Ask the customer if any aftermarket devices have been installed.

← All problems reported for the 2018 Mazda CX-5