2019 Mazda CX-5 Technical Service Bulletins

561 technical service bulletins (TSBs) are on record for the 2019 Mazda CX-5. TSBs are notes manufacturers send to dealers about repair procedures for issues seen in the field. They are not recalls and do not by themselves mean a vehicle has a fault.

• 10177015Jun 22, 2020Engine cooling. If a customer comes in with the following concerns, perform the inspection procedure.  OIL PRESSURE WARNING light and/or the CHECK ENGINE light ON.  DTC P055F and/or P0524 stored.  No driveability concern or engine mechanical noise.  Outside the VIN range in TSB 01-020/18.
• 10177005Jun 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
• 10177012Jun 10, 2020Transmission and drivetrain. When replacing manual or automatic transmission, make sure to remove the plug from the old transmission (as shown below) and then re-install it to the new transmission with a new washer. The new transmissions (including remanufactured A/T) have a shipping plug, as shown in the figures (M/T: black, rubber made; A/T: pink and black, with breather). This plug is for shipping use only and needs to be removed in order…
• 10176975Jun 10, 2020Electrical system, Air bags. Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low.  DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily.
• 10176054May 11, 2020Visibility (wipers, defrost, mirrors). Some vehicles may experience an engine no start/no crank with either of the following DTC's stored: P0615:12 - Starter relay circuit malfunction B112A:12 - IG2 relay circuit malfunction. This may be caused by water contamination/corrosion at electrical connector C-04 due to: Windshield tint installation: Windshield tint installed to block UV light. The water used during the installation of the tint may run down…
• 10174589Apr 29, 2020Electrical system, Latches, locks and linkages, Equipment. Some customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from condensation may drip onto the switch connector and cause corrosion.
• 10174690Apr 28, 2020Transmission and drivetrain. Be aware that some new AWD vehicles have been found with cracked rear differential cases, as shown below. NOTE: This may affect new vehicles just delivered to the dealer or new vehicles in dealer inventory.
• 10174569Apr 23, 2020Engine cooling. Some vehicles may exhibit engine overheating and poor A/C performance with DTC P111A:00 stored in memory.  DTC P111A:00 - Engine coolant temperature is high. NOTE: If the concern occurred during high speed driving, this Service Information is not applicable. Diagnose concern according to MGSS online. This concern may be due to improper control module software, which causes the cooling fan to run improperly…
• 10174567Apr 23, 2020Engine cooling. Some vehicle may exhibit a tapping noise from the engine during idling; etc., and synchronized to the engine rpm. The tapping noise may be caused by the switchable hydraulic lash adjuster (HLA), which may not work properly due to air bubbles accumulated in the oil passage in it.
• 10174574Apr 15, 2020Electrical system, Air bags. Some customers may experience the airbag warning light ON with DTC B00A0:09 stored in the SAS control module memory when the battery voltage is low. DTC B00A0:09 (Occupant classification sensor internal signal output unstable). This concern is caused by the low voltage detection time of the occupant classification sensor (OCS) being too short during cranking, which causes detection of the DTC unnecessarily.
• 10173225Mar 27, 2020Transmission and drivetrain, Engine cooling. A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500 -3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an…
• 10173097Mar 12, 2020Transmission and drivetrain, Brakes, Engine cooling, Equipment. Mazda has developed factory recommended scheduled maintenance services that support all major vehicle systems. Mazda recommends dealers follow the scheduled maintenance tables as cited in the vehicle specific workshop manual or owner's manual. Services performed outside of Mazda's factory scheduled maintenance are not recommended. These services are unnecessary and create unneeded expenses for your customers.
• 10173253Mar 11, 2020Electrical system, Equipment. Some customers may complain about incorrect MAZDA CONNECT clock time. This may be caused by an incorrect clock GPS Sync setting.
• 10173227Mar 11, 2020Engine cooling. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms:  The engine takes longer to warm up.  The engine temperature gauge fluctuates.  The low coolant temperature indicator (blue) light stays on longer or comes on while driving.  Poor heater performance, especially at idle.
• 10173100Mar 6, 2020Brakes, Equipment. Some vehicles may exhibit a squeak noise from the rear brakes while braking lightly. The squeak noise may occur more frequently when driving at slow speeds. The noise is caused by poor contact between the guide plate and the mounting support.
• 10173228Mar 4, 2020Equipment. The owner’s manual contains procedures and precautions for the maintenance and cleaning of plastic parts, like the brand emblem. However, it is still important to remind customers about these precautions. Customers should never use inadequate, harsh or aggressive cleaning products on plastic parts.
• 10173249Mar 3, 2020Forward collision avoidance, Equipment. Some vehicles may have one of the following DTCs stored in memory:  C1001:92 - Forward sensing camera (FSC) poor field of view  B14F0:92 - General temporary failure in forward sensing camera (FSC) DTC C1001:92 or B14F0:92 set as a past record for low visibility of the Forward Sensing Camera (FSC). It does not mean there is an actual FSC defect.  In some cases the customer may have a concern with…
• 10171840Feb 28, 2020Engine cooling. Some customers may experience the CHECK ENGINE LIGHT ON with DTC P0126:00 (Thermostat stuck open) and one or more of the following symptoms: The engine takes longer to warm up. The engine temperature gauge fluctuates. The low coolant temperature indicator (blue) light stays on longer or comes on while driving. Poor heater performance, especially at idle.
• 10171836Feb 28, 2020Equipment. DTC P0942:49 TROUBLESHOOTING: P0942:49 is missing from the Workshop Manual on MGSS. Follow the repair procedure below to repair the vehicle until the information is added to the Workshop Manual.
• 10171833Feb 27, 2020Equipment. SiriusXM Traffic Plus and Travel Link are displayed with Mazda in-vehicle factory navigation systems. Both of these services provide information in the U.S. & Canada. NOTE: SiriusXM Traffic Plus and Travel Link subscription is free of charge for 3 years only if equipped with factory installed navigation system. NOTE: 2019-2020 Mazda3 and 2020 CX-30 are not equipped with factory installed navigation system,however…
• 10171843Feb 26, 2020Wheels. Some automotive cleaning products contain strong acid or alkali. When these types of cleaners are used to clean the wheels on Mazda vehicles, the chemicals contents penetrate the clear coating of the wheel surface and damage the paint under the clear coating. The damaged area has the appearance of dark stains.
• 10171792Feb 26, 2020Transmission and drivetrain. Service part Automatic Transaxles (ATX) manufactured on or after July, 2018 are shipped with a blank TCM that requires configuration. NOTE: The following Caution is included with every ATX that requires configuration.
• 10171844Feb 20, 2020Brakes. Some vehicles may exhibit grooves (1) in rear brake disc plate(s), as shown below. This concern is mostly found on new or low mileage vehicles, when the brakes are new. The grooves may be caused through abrasion from the accumulation of metal particles from the rear brake disc plates. The metal particles get caught between the brake pads and disc plates causing groove damage. To eliminate this concern, the disc…
• 10171780Feb 18, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10171848Feb 13, 2020Visibility (wipers, defrost, mirrors). Some vehicles may exhibit power outer mirror(s) that do not fold in and/or out when using the outer mirror switch. This concern may be caused by insufficient water tightness, allowing water to enter the electric folding unit resulting in corrosion damage. To eliminate this concern, the overlapping area (1) of the water-proof seal (inside electric fold-in unit) has been extended.
• 10171841Feb 13, 2020Engine cooling. Some customers may experience a check engine light illumination with DTCs P24C6:00, P24AE:00, P24B1:00 and/or P24AF:00 stored in PCM memory.
• 10171787Feb 11, 2020Equipment. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns. Audio System, Bluetooth®, Center Dislay, DTC, i-ACTIVESENSE, Maintenance Monitor, Navigation, Noise, Reboot / Frozen Screen / Slow Response, USB / Aux Voice Command, How to Check Navi SD Card VIN Lock.
• 10171786Feb 11, 2020Equipment, Electrical system, Engine cooling. A valve tapping or knocking noise may be heard from the top end after the engine cools down (the vehicle is parked overnight) or after it has been idling for an extended time. The tapping noise will decreases as the vehicle is being driven or if the rpm is held above 2500-3000 RPM. This may be caused by the valve Hydraulic Lifters (HLA) bleeding down as the engine cools or when the engine has been idling for an…
• 10171784Feb 5, 2020Engine cooling, Electrical system. If you encounter a vehicle with "ENGINE OIL LEVEL HIGH" message displayed in the instrument cluster, perform the following inspection:
• 10170941Jan 29, 2020Brakes. Some vehicles exhibit brake related concerns such as brake noise, brake judder or brake dragging. If you encounter a customer complaint for any one of these symptoms, refer to the following information to understand why symptoms may occur, and to better assist the customer in resolving their specific brake concern.
• 10170940Jan 29, 2020Seats, Equipment. Due to a vehicle side logic change for the vehicles listed above, the seat warming and seat ventilation systems will no longer automatically turn on when the vehicle is started using the MMS accessory. Both features will now require a manual setting every time the vehicles are restarted after being turned off. Refer to the vehicle owner’s manual for more details on proper seat warmer/seat ventilation operation.
• 10170942Jan 23, 2020Seats. Some customers may complain that their seat warmers or seat ventilation do not turn on when the engine is restarted after being left on when turning off the engine. The logic has changed from previous Mazdas where the seat warmers and seat ventilation automatically turned on when the engine was restarted.
• 10170814Jan 23, 2020Steering. Some customers may complain that the steering wheel is off center more than 3° even when driving straight on a flat road. Customers having this concern should have their vehicle repaired using the following repair procedure.
• 10170813Jan 23, 2020Equipment, Electrical system. Some vehicles may experience the CHECK ENGINE LIGHT ON with DTC P2610 and P2507 stored in memory after engine start and room fuse 15A (A) removed. P2610:00: Instrument cluster internal engine off timer performance problem  P2507:00: PCM battery voltage low input. As a past malfunction, the customer will not notice it (no warning light illuminated), but the DTC may be found during a vehicle service…
• 10170943Jan 15, 2020Electrical system, Equipment. Some customers may complain about a MAZDA CONNECT system reboot or blank screen. Use the troubleshooting chart below to repair the vehicle.
• 10170829Jan 15, 2020Electrical system, Body and structure, Engine cooling. LACK OF POWER UNDER HEAVY LOAD WITH NO WARNING LIGHTS OR DTCS: Some customers may complain of a lack of power under heavy load without any warning lights or DTCs. This concern may be due to a loose or detached hood weatherstrip, which can cause a blockage or restriction in the air intake system.
• 10170819Jan 13, 2020Equipment, Body and structure. Some vehicles may experience stains appearing on the hood, roof and/or trunk of the vehicle. This concern is most likely to be found in a cold weather areas just after the RAPGARD is removed at PDI. This may be caused by moisture which has been trapped and condensed between the paint and the RAPGARD. These types of stains can be removed with a heat gun or an infrared drier.
• 10170818Jan 13, 2020Seats. At PDI or when new vehicle is delivered, some customers may complain about wrinkles on the leather seat cushion and/or seat back surface. Customers having this concern should have their vehicle repaired by a qualified upholstery repair specialist using the following repair procedure.
• 10170817Jan 13, 2020Equipment. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
• 10170661Jan 9, 2020Equipment, Electrical system. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement.  Mazda vehicles are…
• 10170656Jan 9, 2020Suspension, Equipment. Some customers may complain of signs of oil on the struts or shock absorbers. In most cases the oil that is present is normal, and a result of the oil that remains on the shaft during the normal sweeping process of the shaft seal. Follow the inspection guidelines below to determine if the condition is a result of the normal sweeping process or a failure of the shaft seal.
• 10169505Dec 20, 2019Wheels. Some vehicles may exhibit corrosion of the wheel nuts. This is caused by torsional stress concentrating on the tip of the wheel nut because of the thin and long shape of the nut, which damages the coating and causes the corrosion. To correct this issue, the width across the flats of the wheel nuts have been changed from 17mm to 21mm.
• 10169542Dec 19, 2019Equipment, Electrical system. All Mazda Connect vehicles in new car inventory must be updated to the software version listed below in this TSB as part of the New Car Ready Step 3 process. Make sure the new vehicle specialist receives a copy of this bulletin. Some vehicles may experience the symptoms mentioned below, which can be fixed with the latest software update (Version 70.00.352 or later).
• 10169540Dec 19, 2019Equipment, Engine cooling. If an engine assembly is replaced after a catastrophic internal mechanical failure, clean the intake manifold internally before installing a replacement engine assembly. If the intake manifold is not cleaned properly, the replacement engine may fail prematurely. Metallic debris from the old engine (with catastrophic internal mechanical failure) may rest inside the intake manifold.
• 10169513Dec 18, 2019Other or unknown, Transmission and drivetrain. WARRANTY GUIDELINES FOR RETURNED TRANSMISSION CORES. Be advised that the Mazda Remanufactured Transmission Center (MRTC) has found that up to 30% of the returned transmission cores either included the wrong transmission oil cooler, or the oil cooler was missing altogether. IMPORTANT NOTE: ALWAYS REMEMBER TO INCLUDE THE ORIGINAL OIL COOLER WITH THE RETURNED TRANSMISSION CORE!
• 10169539Dec 17, 2019Equipment. A musty/mildew type odor may come from the vents when the air conditioning (A/C) system is operating. It is most noticeable when the A/C is first turned ON. This odor is the result of mold growth in the A/C evaporator/cooling unit which is caused by condensation, dust, and pollen within the cooling unit. This condition is usually worse during high humidity conditions. “Mazda Air Cooling Coil Coating” is…
• 10169543Dec 13, 2019Equipment, Visibility (wipers, defrost, mirrors), Other or unknown. Accessory instructions can be found in the Accessory eCatalog. https://ecatalog.trademotion.com/. Audio/Electrical, Exterior, Interior: - Mazda Mobile Start (MMS) - Remote Engine Start - Wireless Charging Pad - Mirror - Navigation - Rear Parking Sensors - Rear Seat Entertainment - Smartphone Screen Mirroring - Bumper Trim/Guards - Door Mirror Caps - Fog Lights - Moonroof Wind Deflector - Roof Rack - Side Window…
• 10169537Dec 13, 2019Engine cooling, Equipment. There is a concern that some water pumps are being replaced that are not faulty, due to signs of a very small coolant leak from the bleed hole. This Service Bulletin is to inform you about the water pump sealing mechanism and the criteria if replacement is necessary or not.
• 10169509Dec 5, 2019Transmission and drivetrain, Engine cooling. GUIDE LINES AND PHOTOS TO DETERMINE IF FLUID/OIL SEEPAGE OR LEAK IS SEVERE ENOUGH TO REQUIRE WARRANTY REPAIR OR TO CLEAN AND MONITOR. Some customer's might state that they notice fluid or oil leaking/dripping on the ground when the vehicle is parked. For this concern, inspect the vehicle for any trace of a fluid or oil leak and use the following examples as a guide to determine if it is severe enough to require a…
• 10168785Nov 26, 2019Engine cooling. Some vehicles may exhibit oil leakage from the drive belt auto tensioner and rattling noises from the engine compartment. This may be caused by insufficient sealing at the drive belt auto tensioner damper when the auto tensioner fully operates under both high ambient temperature and high load conditions. To eliminate this concern, the shape of the drive belt auto tensioner damper has been changed.

← All problems reported for the 2019 Mazda CX-5